Rockford Fosgate P300X2 Handleiding

Rockford Fosgate Autoradio P300X2

Lees hieronder de 📖 handleiding in het Nederlandse voor Rockford Fosgate P300X2 (2 pagina's) in de categorie Autoradio. Deze handleiding was nuttig voor 8 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

RIGHTLEFT

FRONT REAR

BRIDGED

RIGHTLEFT

RIDGED

SPEAKERS

REMOTE

PUNCH LEVEL

INPUT CLIP PASS-THRU REARFRONT

RIGHT

LEFT

RIGHT

LEFT

B+REM GND

PLC-OUTPLC IN

B+

REM GND

INPUT CLIP PASS-THRU REARFRONT

RIGHT

LEFT

RIGHT

LEFT

* Specifications subject to change without notice. Images

depict typical setup. Refer to manual for additional wiring

options.

RIGHTLEFT

FRONT REAR

BRIDGED

RIGHTLEFT

BRIDGED

SPEAKERS

Be sure to connect speakers and

Punch Level Control - PLC

(if equipped) after amplifier output

clip adjustment.

(see reverse)

Optional Accessory

PLC2

Battery

*Keep grounds as

short as possible

*Keep grounds as

short as possible

Source Unit

Connect to chassis

ground of vehicle

Less than 18”

Fuse

Amplifier Quick Setup

RIGHTLEFT

FRONT REAR

BRIDGED

RIGHTLEFT

BRIDGED

SPEAKERS

PUNCH

INPUT CLIP PASS-THRU REARFRONT

RIGHT

LEFT

RIGHT

LEFT

B+REM GND

PLC-OUTC-IN

Input Clip Indicator Setup

Be sure to disconnect all speakers

from the amplifier.

Failure to comply may cause damage

to connected components and/or

amplifier.

Step 1 - Input

Adjust the Bass & Treble levels on the

source unit to flat.Turn on the source unit with volume set to zero.

Play test tone* or music CD for setup.

Note: Use the 40Hz @ 0dB tone (Track 5) for

mono amplifier applications or the 1kHz @ 0dB

tone (Track 7) for multi-channel amplifier

applications. Be sure your x-over is switched to

the appropriate filter setting.

*Test tones available at https://rftech.custhelp.com/app/answers/de-

tail/a_id/1126/ Scroll to the bottom of the page and download your preferred

format.

Increase the source unit volume until the

Input Clip Indicator illuminates red.

Note: Input Clip can be viewed remotely

with optional PLC2.

Decrease the source unit volume slightly

until the light turns completely off. This

establishes your maximum source unit

volume for adjusting the Output Clip

Indicator.

Note: Some source units will not clip.

Reconnect all speakers and

Punch Level Control - PLC (if

equipped) to the amplifier. Be

sure to maintain proper

speaker polarity.

Turn the source unit volume

down.

Step 2 - Input

Step 3 - Input

Step 4 - Input

Step 5 - Input Step 6 - Input Step 8 - Output Step 9 - Output

Step 10 - Output

Volume

Be sure to disconnect

Punch Level Control - PLC

(if equipped) from the

amplifier.

Step 7 - Output

Output Clip Indicator

Setup

Adjust the Input Level knob

until the Output Clip Indicator

illuminates to the appropriate

color. Repeat for all channel

levels of input.

INPUT CLIP PAS -THRUFRONT

RIGHT

LEFT

RIGH

LEF

INPUT CLIP PAS -THRUFRONT

RIGHT

LEFT

RIGH

LEF

Volume

Amplifier Clip Indicator Setup

1230-58089-02-A

Product specificaties

Merk:	Rockford Fosgate
Categorie:	Autoradio
Model:	P300X2
Kleur van het product:	Zwart
Gewicht:	4300 g
Breedte:	191.7 mm
Diepte:	250.4 mm
Hoogte:	60.5 mm
Certificering:	CE
Efficientie:	69 procent
Input sensitiviteit:	150 mV
Audio RCA-ingangen:	1
Versterker klasse:	A/B
Aantal versterker kanalen:	2 kanalen
RMS vermogen uitvoer per kanaal (4 Ohm):	100 W
High pass filter:	Ja
Low pass filter:	Ja
Audio RCA-uitgangen:	1
RMS vermogen uitvoer per kanaal (2 Ohm):	150 W
Bass boost:	0 - 18 dB
Maximaal uitgangsvermogen per kanaal (4 Ohm):	120 W
Maximaal uitgangsvermogen per kanaal (2 Ohm):	203 W
Overbrugd uitgangsvermogen (max):	300 W
High-pass filterbereik:	50 - 250 Hz
Low-pass filterbereik:	50 - 250 Hz
Frequentierespons:	20 Hz
CEA-uitgangsvermogen:	100W x 2 @ 4Ω ≤1.0% THD+N