Rinnai RI-522MM Handleiding

Rinnai Fornuis RI-522MM

Lees hieronder de 📖 handleiding in het Nederlandse voor Rinnai RI-522MM (2 pagina's) in de categorie Fornuis. Deze handleiding was nuttig voor 48 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

S P E C I F I C A T I O N

PREPARING THE UNIT FOR USE

Automatic Ignition (Piezo Magnetic)

(Figure No.1) (Figure No. 2)

15 cm 15 cm 100cm

15 cm

1. Top Plate

2. Small Burner Head

3. Small Hole Pan Support

4. Big Hole Pan Support

5. Simmer Burner Head

6. Big Burner Head

7. Ignition Knob

1. Check to ensure that all parts of the gas cooker are complete.

2. A minimum clearance is 15 cm from the side / back wall and 100 cm from

the ceiling is required when installing the gas cooker. The gas cooker shall

be placed in a good ventilated room. (Figure No. 1)

3. Using a screwdriver affix the rubber legs with the provided screw into the

designated hole on the gas cooker's bottom. (Figure No. 2)

4. Insert the ignition knob in its correct position by pushing it inward firmly.

(Figure No. 3)

5. Place the Simmer Burner Head onto the gas pipe located at the gas

cooker’s. (Figure No. 3)

6. Place the small hole pan support on the left burner and big hole pan

support on the right burner. (Only for RI-522M, RI-602M) (Figure No. 3)

7. Push the rubber hose on the gas pipe and regulator as far as it will go.

Secure the hose using a hose clamp.

8. Open the main valve on the gas cylinder. In the event of gas leak, close

the main valve immediately and open the windows in the room to allow

the gas to escape.

Safe and easy to operate, the burners will ignite automatically when the control knobs are pushed and turned in counter-clockwise

direction. For best results from your Rinnai Gas Cooker, Please read the instruction given below carefully prior to operating the unit.

(Figure No. 3)

Model

RI-522M

RI-511M

RI-522MM

RI-602M

RI-602MM

Dimension

Height Width Length

Net. Weight

Gas Consumption / h Gas Inlet

Connection

157 mm

154 mm

700 mm

280 mm

378 mm

380 mm

4.2 Kg

2.3 Kg

LHS LHS

LPG (30 mbar/3.0 kPa) NG (25 mbar/2.5 kPa)

RHS RHSTotal Total

8.1 kW

4.8 kW

8.4 kW

4.9 kW

Rubber Hose

mmØ9.5

700 mm

702 mm

378 mm

380 mm

4.5 Kg

4.6 Kg

4.8 Kg

4.8 kW

3.3 kW

4.8 kW

3.3 kW

–

4.9 kW

3.5 kW

4.9 kW

3.5 kW

–

4.8 kW

–

4.9 kW

–

9.6 kW

8.1 kW

9.7 kW

9.8 kW

8.4 kW

9.8 kW

OPERATING INSTRUCTIONS GAS BURNER

NAME OF PARTS

MODEL:

RI-511M

RI-522M

RI-522MM

RI-602M

RI-602MM

080112

Pan Support

Ignition Knob

Simmer Burner Head

5 646

5 6

RI-511M

RI-522M RI-602M

RI-522MM RI-602MM

562

343

OPERATING THE UNIT MAINTENANCE AND CARE

ATTENTION

1. Igniting the burner and adjusting the flame.

*) Open the valve on the cylinder

2. If no flame, turn back the knob to “OFF" position, repeat the

ignition procedure as above.

3. Air Control

For good flame, turn Damper upward or downward until a blue-

colored flame is obtained. (Figure No. 6)

!RHS Burner (All model)

!LHS Burner (RI-522MM, RI-602MM)

Operate the burner with its double ring burner and “MAX”,

“Simmer” and “Minimum Simmer” flame selector as follow:

Maximum Flame

Push the knob in fully and turn counter clockwise to “MAX” in this

position both outer and inner burner will burn fully.

ØFlame is adjustable between the “MAX” and “OFF” position by

slowly turning the knob to the “OFF” position. (Figure No 5).

Simmer Flame

Turn the knob to the left on the “Simmer” direction the outer burner

will be switched off and only the smaller inner burner (simmer) will

function.

Minimum Simmer Flame

Turn the knob to left on the “Minimum Simmer”, Where the inner

burner will burn smaller.

!LHS Burner (RI-522M, RI-602M)

Maximum Flame

Push the knob in fully and turn it counter clockwise to “MAX”

position, where the burner will burn fully.

Minimum Flame

From “MAX” position turn the knob to the left on “MIN” position,

where the burner will burn smaller.

Ø Flame is adjustable between the “MAX” and “OFF” positions by

slowly turning the knob to the “OFF” position. (Figure No. 4)

1. Using a brush, to clean the Burner Head and Burner Top surface

of any dust adhering to these part.

2. Wipe clean the pan support, and other Stainless Steel Part with

a small amount of Soapy Water. Don't use the alcohol or

gasoline, because can damaged the part.

3. Clean the Electrodes as dust adhering to these parts may

prevent a good ignition. (Figure No. 7)

1. Keep away any flammable material / liquid from the gas cooker.

2. The gas cooker shall be placed in a good ventilated room.

3. Never use one single rubber hose for two gas cooker.

4. Do not place any objects that may easily be blown away by the

wind on the gas cooker.

5. In the event of gas leak, do not switch on any fan/ lighter.

6. Do not use any small cooking utensil that may cover the burner

flame and thereby extinguishing it.

7. Do not use any large cooking covering the entire gas cooker

surface.

8. Replace any damage / cracked rubber hose immediately.

9. Don't touch the gas cooker immediately after cooking.

10.Take care that no boiling water spills onto the gas burner's top

surface.

11.Do not use the gas cooker to dry.

12.Do not leave the gas cooker unattended when on.

13.Do not route the rubber hose under the gas cooker.

TROUBLE SHOOTING GUIDE

If trouble occurs, fix it referring to the above table. But if the problem still remain, or in case a serious malfunction, and if you are doubt,

then take the gas cooker to our AFTER SALES SERVICE for repairing without trying to repair it your self.

RI52-207-6x01

(Figure No. 5) (Figure No. 7) (Figure No. 4) (Figure No. 6)

* Push in fully

OFF

* Turn

Counter-clockwise

ON/MAX FLAME

MINIMUM

FLAME

* Push in fully

* Turn

Counter-clockwise

OFF

MAX FLAME

SIMMER

MINIMUM

SIMMER

MED FLAME

Flame does

not ignite

Main Gas Stopcock is not turned on.

Air remains in the gas piping.

Bend or crushed rubber tubing.

Piezo electrode or insular is dirty.

The gas cooker out of order.

Cracks or holes in the rubber tubing.

Rubber tubing is not connected properly.

Regulator leakage.

The gas cooker out of order.

Smell of gas

Turn off the gas cooker once and than turn it in fully.

Straighten it, or replace it.

Clean it with dry cloth.

Request to AFTER SALES SERVICE for repair.

Replace it with a new one.

Connect the rubber tubing properly.

Replace it with a new one.

Request to AFTER SALES SERVICE for repair.

Flame abnormal

Air supply is not properly adjusted.

The gas cooker out of order. Request to AFTER SALES SERVICE for repair.

Clean the clogged part.

Fix burner body properly.

TROUBLE CAUSE SOLUTION

Adjust is properly. (See Page 2 Fig.6)

Burner is not fitted properly.

Flame outlet of burner is clogged.

Repeat ignition operation until all air in the piping is purged out completely.

Product specificaties

Merk:	Rinnai
Categorie:	Fornuis
Model:	RI-522MM
Apparaatplaatsing:	Aanrecht
Soort bediening:	Draaiknop
Kleur van het product:	Roestvrijstaal
Ingebouwd display:	Nee
Gewicht:	4500 g
Breedte:	700 mm
Diepte:	378 mm
Hoogte:	157 mm
Soort materiaal (bovenkant):	Roestvrijstaal
Aantal branders/kookzones:	2 zone(s)
Type kookplaat:	Gaskookplaat
Electronische ontsteking:	Ja
Aantal gaspitten:	2 zone(s)
Aantal elektronische kook zones:	0 zone(s)
Controle positie:	Voorkant
Aangesloten lading (elektrisch):	- W
Aangesloten lading (gas):	- W
Vorm sudderpit/kookzone:	Rond
Vorm grote pit/kookzone:	Rond
Aantal gelijktijdig te gebruiken kookzones:	2
Anti-slip voetjes:	Ja
Type gas:	Liquefied Petroleum Gas (LPG)