RIDGID 456 Handleiding

RIDGID Niet gecategoriseerd 456

Lees hieronder de 📖 handleiding in het Nederlandse voor RIDGID 456 (1 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 115 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/1
La cintreuse 456 Tri-Bender sert au cintrage des tubes recuits Ø 1/4",
5/16" et 3/8".
Le port systĂ©matique de lunettes de sĂ©curitĂ© s’im-
pose afin de limiter les risques de blessure oculaire.
Utilisation générale
1. Relevez la poignée de cintrage afin de positionner le tube dans la
rainure appropriée de la poignée à galet. Assurez-vous que le tube
s’engage bien dans la bride
(Figure 1)
.
2. Rabattez la poignĂ©e de cintrage jusqu’au tube, puis fermez-la contre
la poignĂ©e de gabarit jusqu’à ce que le repĂšre « 0 » de la poignĂ©e
de cintrage s’aligne sur le repĂšre d’angle de cintrage appropriĂ© de la
poignée à galet
(Figure 2)
.
Figure 1 Figure 2
RepĂ©rage de l’axe de cintrage par
rapport à un élément donné (embout
de tuyau, coude, etc.)
Coudes à 90°
‱ RepĂ©rez l’axe de cintrage (X) en marquant le tube Ă  la distance
voulue d’un Ă©lĂ©ment existant (embout de tuyau, coude, etc.). Ceci
donnera l’axe de la partie coudĂ©e du tuyau.
‱ Positionnez le tube dans la cintreuse comme indiquĂ© Ă 
l’article 1
.
‱ Si l’élĂ©ment existant se trouve Ă  la du repĂšre tracĂ© sur le tubegauche
(Figure 3 – Avant)
, alignez le repÚre sur la ligne « L» de la poignée
de cintrage.
‱ Si l’élĂ©ment existant se trouve Ă  la droite du repĂšre tracĂ© sur le tube
(Figure 4 – Avant)
, alignez le repÚre sur la ligne « » de la poignéeR
de cintrage.
Figure 3 – Avant (Before) Figure 3 – Aprùs (After)
Ridge Tool Company/Elyria, Ohio, U.S.A.
6/09
Printed in U.S.A. 999-998-655.10
456 Tri-Bender Instruction Sheet
‱ Align the mark on the tube with the unlabeled line on the shoe han-
dle
(see Figure 5)
.
Figure 5 – Before Figure 5 – After
‱ With the mark on the tube appropriately aligned, move the shoe
handle so that the “0” line aligns with the 45 degree line on the form
handle.
If you have any question concerning this Ridge Tool product:
‱ Contact your local RIDGID distributor.
‱ Visit www.RIDGID.com or www.RIDGID.eu to find your local Ridge
Tool contact point.
‱ Contact Ridge Tool Technical Services Department at techser-
vices@ridgid.com, or in the U.S. and Canada call (800) 519-3456.
The 456 TR-Bender is used to bend 1/4", 5/16" and 3
/8" soft tubing.
Always wear safety glasses to reduce the risk of eye
injury.
General Use
1. Rotate the shoe handle out of the way and position the tube in the
appropriate groove in the form handle. Be sure that the tube
engages the tube latch
(Figure 1).
2. Rotate the shoe handle into contact with the tube, and rotate the
shoe handle around the form handle so that the “0” line on the
shoe handle aligns with the desired degree of bend on the form
handle
(Figure 2)
.
Figure 1 Figure 2
Measured Bends Relative to Other
Features (Tube ends, Bends, etc.)
For 90° Bends:
‱ Mark the tube at the desired distance (X) from the feature (end of
tube, bend, etc.). The center of the leg of the bend will be this dis-
tance from the feature.
‱ Place the tube in the bender as described in
Step 1
above.
‱ If the feature is to the LEFT of the mark
(see Figure 3 – Before),
align the mark on the tube with the “ ” line on the shoe handle.L
‱ If the feature is to the RIGHT of the mark
(see Figure 4 – Before)
,
align the mark on the tube with the “ ” line on the shoe handle.R
Figure 3 – Before Figure 3 – After
Figure 4 – Before Figure 4 – After
‱ With the mark on the tube appropriately aligned, move the shoe
handle so that the “0” line aligns with the 90 degree line on the form
handle.
(See Figures 3 and 4 – After).
For 45° Bends:
‱ Mark the tube at the desired distance (X) from the feature (end of
tube, bend, etc.). The center of the arc segment will be this distance
from the feature.
‱ Place the tube in the bender as described in
Step 1
above.
Shoe
Handle
Tube
Latch
Form
Handle
Mark On
Tube
XX
Mark On
Tube
X
L Line
R Line
X
Mark On
Tube
XUnlabeled
Line X
WARNING
Cintreuse 456 Tri-Bender : Mode d’emploi
AVERTISSEMENT
Shoe Handle – PoignĂ©e de cintrage
Tube Latch – Bride
Form Handle – PoignĂ©e Ă  galet
L Line – Ligne L
Mark On Tube – Repùre du tube

Product specificaties

Merk: RIDGID
Categorie: Niet gecategoriseerd
Model: 456

Heb je hulp nodig?

Als je hulp nodig hebt met RIDGID 456 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd RIDGID

RIDGID

RIDGID FlexShaft Handleiding

18 Augustus 2024
RIDGID

RIDGID HKO-186 Handleiding

5 Maart 2024
RIDGID

RIDGID Raprench 10 Handleiding

5 Maart 2024
RIDGID

RIDGID KT-190 Handleiding

5 Maart 2024
RIDGID

RIDGID 760 FXP Handleiding

27 Februari 2024
RIDGID

RIDGID 700 Handleiding

26 Februari 2024
RIDGID

RIDGID micro CA-350 Handleiding

26 Februari 2024
RIDGID

RIDGID KWIK-SPIN+ Handleiding

26 Februari 2024
RIDGID

RIDGID 690-I Handleiding

26 Februari 2024
RIDGID

RIDGID 600-I Handleiding

26 Februari 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Gourmetmaxx

Gourmetmaxx 03863 Handleiding

24 December 2024
Vello

Vello PGS-P Handleiding

24 December 2024
Venom

Venom Quad Charging Station VS4796 Handleiding

24 December 2024
Nec

Nec IPJ2000CM Handleiding

24 December 2024
Monogram

Monogram ZKPN Handleiding

24 December 2024
Philips

Philips Quick Clean Pot QCP10 Handleiding

24 December 2024
Philips

Philips Senseo HD7002 Handleiding

24 December 2024
D-Link

D-Link DUB-C2 Handleiding

24 December 2024
Nec

Nec MultiPresenter Stick DS1-MP10RX1 Handleiding

24 December 2024
Nec

Nec DS1-TM01 Handleiding

24 December 2024