Quantum Edge 3 Handleiding
Lees hieronder de 📖 handleiding in het Nederlandse voor Quantum Edge 3 (15 pagina's) in de categorie Rolstoel. Deze handleiding was nuttig voor 8 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/15
11
Initial Assembly
Your power chair may require some assembly either
before initial use or after transportation. It may also require
disassembly to make some comfort adjustments. Figure 5
details those parts of the power chair that are designed
to be disassembled and assembled by an end user or by
a qualified caregiver before using the product or making
comfort adjustments.
NOTE: Any nylon insert lock nut removed during the
disassembly or adjustment of the power chair must be
replaced with a new nut. Nylon insert lock nuts should
not be reused as it may cause damage to the nylon
insert, resulting in a less secure fit. Replacement nylon
insert lock nuts are available at local hardware stores or
through your Quantum Rehab Provider.
Seat Installation
It may be necessary to install the seat either prior to initial
operation or after transporting your power chair. Contour
seats are attached to the power base with the Universal
Mounting System (UMS). The UMS consists of universal
parts that may be attached to the seat, regardless of seat
width or seat depth. The two main components are aluminum
extrusions mounted to the seat base. These extrusions attach
to a pair of trapeze bars that are mounted to the power base.
See figure 6.
NOTE: If your power chair is equipped with a Synergy
Seat or a TRU-Balance® 3 Power Positioning System,
refer to the information provided in separate manuals.
Do not pick up the seat frame by the armrests. They are
free to pivot, and you may lose control of the seat if they
do so.
To install the seat:
1. Tilt the seat back and slide the rear extrusion onto the
rear trapeze bar. See figure 6.
2. Lower the front extrusion onto the front trapeze bar until
the seat latches into place.
3. Flip the seat latch safety down.
Make sure the seat latch safety is flipped down before
using your power chair.
4. Install the controller and route the harness to the back of
the power base. See figure 7, 8, 9, or 10.
Prevent controller harness damage! Avoid routing the
controller harness on the outside of the armrest pad.
Route the harness under the armrest or toward the
inside of the armrest pad. Use correct tie-down points for
controller harness to prevent the harness from getting
caught in the drive tires, pinched in the seat frame, or
damaged when passing through doorways.
ASSEMBLY
WARNING!
WARNING!
Figure 5. Assembly View
MANDATORY!
Armrest Angle
Adjustment
Controller
Position
Foot Platform
Angle Adjustment
Foot Platform
Height/Depth Adjustment
Figure 6. Universal Mounting System and Contour Seat
Front Extrusion
Rear Extrusion
Seat Latch Safety
Trapeze Bars
5. Plug the controller connector into the rear of the power
base. See figure 1.
6. Secure the controller harness to the armrest receiver
with wire ties. See figure 7, 8, 9, or 10.
16
Seat Position
You can move the seat forward or rearward by changing the
extrusion mounting position.
To change the position:
1. Turn off the power to the controller.
2. Make sure the power chair is in drive mode.
3. Unplug the controller connector(s) from the power base.
4. Remove the seat from the power base.
5. Remove both extrusions from the bottom of the seat.
6. Reposition the extrusions on a different set of mounting
holes. You must move both extrusions the same number
of holes either forward or backwards. See figure 15.
7. Fasten the extrusions back onto the bottom of the seat.
8. Reinstall the seat.
9. Reconnect the controller to the power base.
Manual Recline Seatback Adjustment
If your power chair is equipped with a reclining seat, you can
adjust the seatback angle with the seatback release lever.
The lever is located on the right side of the seat base.
To adjust the recline angle:
1. Pull up on the seatback release lever.
2. Lean forward or backward to the desired position.
3. Release the lever.
Armrest Width Adjustment
You can change each armrest’s width independently of
the other.
NOTE: Changing the armrest width may increase the
overall width of your power chair.
To change the armrest width:
1. Locate the two armrest knobs on each side of the
armrest receiver bracket. See figure 16.
2. Loosen the knobs.
3. Slide the armrests in or out to the desired width.
4. Tighten the knobs.
Armrest Angle Adjustment
To change the armrest angle:
1. Lift the armrest straight up so that it is perpendicular to
the floor. See figure 16.
2. Loosen the jam nut.
3. Turn the adjusting screw to raise or lower the front of the
armrest.
4. Tighten the jam nut to lock the adjusting screw into place.
Armrest Height Adjustment
To change the armrest height:
1. Loosen the two setscrews located on the armrest
receiver. See figure 16.
2. Raise or lower the armrest to the desired height.
3. Tighten the setscrews to secure the armrest.
Controller Position
You can move the controller in toward or out away from the
armrest, or change the position of the controller for either
left-hand or right-hand use.
Do not place the controller harness so that it can be
pinched in the seat frame or the power base frame.
To extend the controller:
1. Flip up the armrest so it is perpendicular to the floor.
2. Loosen the setscrew on the controller bracket. See
figure 16.
3. Slide the controller into or out of the armrest to the
desired position.
4. Tighten the setscrew to secure the controller.
To change the controller position:
1. Turn off the power to the controller.
2. Unplug the controller connector(s) from the power base.
3. Remove any wire ties securing the controller harness to
the armrest.
4. Flip up the armrest so it is perpendicular to the floor.
5. Loosen the setscrew on the controller bracket.
6. Slide the controller out of the armrest.
7. Loosen the setscrew in the other armrest.
8. Place the controller in the other armrest.
9. Tighten the setscrews in both armrests.
10. Route the controller harness to the back of the power
base and plug in the controller.
11. Secure the controller harness to the armrest with wire
ties. See figure 8.
NOTE: If your power chair is equipped with a Synergy
Seat or TRU-Balance 3 Power Positioning System, refer
to the information provided in supplemental manuals
provided with your seating system.
Figure 16. Seatback/Armrest Adjustment
WARNING!
Jam Nut
Armrest Angle
Adjusting Screws
Armrest Height
Adjusting Screws
Armrest Knob
Controller
Bracket
Setscrew
COMFORT ADJUSTMENTS
Product specificaties
| Merk: | Quantum |
| Categorie: | Rolstoel |
| Model: | Edge 3 |
Heb je hulp nodig?
Als je hulp nodig hebt met Quantum Edge 3 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Rolstoel Quantum
11 November 2024
8 Juli 2024
15 Augustus 2023
15 Augustus 2023
15 Augustus 2023
15 Augustus 2023
15 Augustus 2023
15 Augustus 2023
15 Augustus 2023
15 Augustus 2023
Handleiding Rolstoel
- Rolstoel Aidapt
- Rolstoel Alber
- Rolstoel Breezy
- Rolstoel Dietz
- Rolstoel Excel
- Rolstoel Handicare
- Rolstoel Invacare
- Rolstoel Kymco
- Rolstoel Life-Mobility
- Rolstoel Meyra
- Rolstoel Permobil
- Rolstoel Pride
- Rolstoel Quickie
- Rolstoel Shoprider
- Rolstoel Sopur
- Rolstoel Sunrise Medical
- Rolstoel Tekvor Care
- Rolstoel Travelux
- Rolstoel Vela
- Rolstoel Vermeiren
- Rolstoel Wheelzahead
- Rolstoel Zippie
- Rolstoel Otto Bock
- Rolstoel Medline
- Rolstoel 2GOability
- Rolstoel Van Os
- Rolstoel Vitea Care
- Rolstoel Smoov
- Rolstoel Drive Medical
Nieuwste handleidingen voor Rolstoel
25 Maart 2024
25 Maart 2024
8 Maart 2024
8 Maart 2024
8 Maart 2024
8 Maart 2024
8 Maart 2024
8 Maart 2024
8 Maart 2024
8 Maart 2024