Quantum DLT-V4 Handleiding

Quantum Niet gecategoriseerd DLT-V4

Lees hieronder de 📖 handleiding in het Nederlandse voor Quantum DLT-V4 (28 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 206 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/28

DLT-V4 Tape Drive

Quick Start Guide

English- - - - - - - - - - - 1

German - - - - - - - - - - 5

Spanish - - - - - - - - - - 9

French - - - - - - - - - - 13

Japanese - - - - - - - - 17

Korean - - - - - - - - - - 21

Simplified Chinese - 25

Introduction 0

This guide provides instructions on how to configure and install the DLT-V4 tape

drive in the following configurations:

•Internal Tape Drive — SCSI, SATA, and USB versions

•Tabletop Tape Drive — SCSI and USB/eSATA versions

Internal Tape Drive 0

1Inspect the shipping box and contents of the box for damage. If you find any

damage, report it to the shipping company.

2Select a server or workstation to host the tape drive.

3Download the device driver from the following Web site:

http://www.quantum.com/ServiceandSupport/

SoftwareandDocumentationDownloads/DLTV4/Index.aspx.

4Shut down and power off the host and all peripheral devices attached to the

selected host.

5 SCSI Tape Drives Only — If necessary, change the SCSI ID using the SCSI

jumpers (see figure 1). (For complete instructions, see the DLT-V4 Product

Manual.)

NOTE:See the last page of this document for additional resources.

NOTE:Save the packing materials in case you need to move or ship the

tape drive. You must ship the tape drive in the original or equivalent

packing materials to preserve your warranty.

NOTE:The factory default SCSI ID is .5

DLT-V4 Tape Drive Quick Start Guide

Figure 1 Setting the SCSI ID

6Remove the cover from the server or workstation as

described in the server or workstation’s documentation.

See figure 2.

7 SCSI Tape Drives Only — If necessary, install an LVD/SE

host bus adapter in the server or workstation.

8 SCSI Tape Drives Only — Connect an active LVD/SE

terminator onto one end of the SCSI cable, if the tape

drive is the last or only device on the SCSI bus (see

figure 2). If the SCSI cable that came with the SCSI host

bus adapter already has a terminator built into it, do

not use an additional terminator.

Figure 2 Removing the Cover,

Installing, and Terminating

9 SCSI Tape Drives Only —Connect the SCSI cable to the

tape drive and to the SCSI host bus adapter. Connect

the power cable to the tape drive (see figure 3).

NOTE:If the tape drive is not the last or only device

on the SCSI bus, make sure the last device on

the SCSI bus is properly terminated is and

powered on whenever you use the tape drive.

SCSI ID jumpers

Figure 3 Connecting the SCSI

Cables to Rear of Tape Drive

10 SATA Tape Drives Only — Connect one end of the

SATA data cable to the tape drive and the other end of

the SATA data cable to the SATA host bus adapter (see

figure 4).

11 SATA and USB Tape Drives Only — Connect either the

SATA power cable drive power cable to the tape or

drive (see figure 4).

Figure 4 Connecting the SATA

Cables to Rear of Tape Drive

12 Secure the tape drive in the selected server or

workstation with the appropriate M3 mounting screws

(see figure 5). Contact the computer manufacturer if

the server or workstation uses mounting rails for

internal tape drives.

CAUTION:Connect only one power cable to the

drive. Connecting both the SATA power cable

and drive power cable to the tape drive may

damage the drive.

SCSI cable (with terminator)

Drive power cable

SATA

power

cable

SATA

data

cable

Drive

power

cable

Install EITHER

(not both)

DLT-V4 Tape Drive Quick Start Guide

13 USB Tape Drives Only — You must use a SATA data

cable and a SATA-to-USB adapter. Please follow the

installation instructions in the SATA-to-USB Adapter

Installation Guide included with the adapter (also

located on the resource CD.

Figure 5 Securing the Tape

Drive

14 Install the cover on the server or workstation. Connect

the power cables to any attached peripheral devices.

15 Power on any attached peripheral devices.

16 Power on the server or workstation and allow its

operating system to start.

Tabletop Tape Drive 0

1Inspect the shipping box and contents of the box for

damage. If you find any damage, report it to the

shipping company.

2 SCSI Tape Drives Only — If necessary, change the SCSI

ID for the tape drive. Use a small screwdriver or

ballpoint pen to press the buttons above or below the

SCSI ID to increase or decrease the number (see

figure 6). (For complete instructions, see the DLT-V4

Product Manual.)

Figure 6 Changing the SCSI ID

3Select a location near the server or workstation that will

host the tape drive.

NOTE:Save the packing materials in case you need

to move or ship the tape drive. You must ship

the tape drive in the original or equivalent

packing materials to preserve your warranty.

4Download the device driver from the following Web

site: http://www.quantum.com/ServiceandSupport/

SoftwareandDocumentationDownloads/DLTV4/

Index.aspx.

5Shut down and power off the host and all peripheral

devices attached to the selected host.

6 SCSI Tape Drives Only — If necessary, install an LVD/SE

host bus adapter in the server or workstation (see

figure 7).

7 SCSI Tape Drives Only — Connect the SCSI cable to the

tape drive and to the SCSI host bus adapter — or to the

previous device on the SCSI bus (see figure 7).

8 SCSI Tape Drives Only — Connect an active LVD/SE

terminator onto one end of the tape drive, if it is the

last or only device on the SCSI bus (see figure 7).

Figure 7 Connecting the Cables

— SCSI Tape Drive

NOTE:If the tape drive is not the last or only device

on the SCSI bus, make sure the last device on

the SCSI bus is properly terminated and is

powered on whenever you use the tape drive.

LVD/SE host bus

adapter

SCSI cable

Off

Terminator

SCSI cable

Product specificaties

Merk:	Quantum
Categorie:	Niet gecategoriseerd
Model:	DLT-V4
Kleur van het product:	Zwart
Stroomvoorziening:	120/240 VAC
Interface:	SATA 1.0, 160 SCSI, USB 2.0
Soort voeding:	+5/+12 VDC
Intern:	Ja
Mean time between failures (MTBF):	250000 uur
Hoogte, in bedrijf:	-152.4 - 9144 m
Standaardcapaciteit:	160 GB
Capaciteit met compressie:	320 GB
Drive, omvang buffer:	32 MB
Stroomverbruik (typisch):	20 W
Bedrijfstemperatuur (T-T):	10 - 40 °C
Relatieve vochtigheid in bedrijf (V-V):	20 - 80 procent
Type product:	Opslagschijf
Toegangstijd:	84 ms
Overdrachtssnelheid (piek):	1600 MB/s
Doorvoersnelheid:	20 MB/s
Compressieratio:	2:1
Type gegevensopslag:	DLT
Media type:	Tapecassette
Recording density:	219 kbit/duim
Track density:	352
Backupsnelheid (gecomprimeerde gegevens):	72 GB/uur