Qazqa 90501 Handleiding

Qazqa Verlichting 90501

Lees hieronder de 📖 handleiding in het Nederlandse voor Qazqa 90501 (4 pagina's) in de categorie Verlichting. Deze handleiding was nuttig voor 72 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

VAP Duo WL Silver

MODEL: 90501

INTRODUCTION

The Light incorporates a PIR (Passive Infra Red) sensing device which

continuously scans a preset operating zone and immediately switches

the light on when it detects movement in that area. This means that

whenever movement is detected within the range of the sensor the

light will switch on automatically to illuminate pathways, steps,

patios, porches, or whatever area you have selected to light for rea-

sons of safety, convenience or security.

While there is movement within range of the unit the light will

remain on.

WHILE TO FIT YOUR LIGHT

To achieve best results, we suggest you account the following points:

■ Ideally the Light should be mounted 1.8 to 2.5 meters (6 to 8ft)

above the area to be scanned (refer Figure).

■ To avoid damage to unit-do not aim the sensor towards the sun.

■ To avoid nuisance triggering, the sensor should be directed away

from heat sources such as barbecues, Air-conditioners, other

outside lighting, moving cars and ﬂue vents.

■ To avoid nuisance triggering, keeping away from the area of strong

electromagnetic disturbance.

■ Do not aim towards reﬂective surfaces such as smooth white

walls, swimming pools, etc. The Security light scanning speciﬁcati-

ons (Max. 8 meters at 130°) may vary slightly depending on the

mounting height and location. The detection range of the unit

may also alter with temperature change. Before selecting a place

to install your light you should note that movement across the

scan area is more eﬀective than movement directly toward or

away from the sensor. (refer Figure). If movement is made walking

directly towards or away from the sensor and not across, the

apparent detection range will be substantially reduced. (refer

Figure )

FITTING THE UNIT

Installation by a licensed electrician and according to IEC wiring Regu-

lation.

Before commencing any electrical work, ensure mains supply cables

are isolated by switching oﬀ and removing the relevant fuse.

1. Unscrew the Terminal Box Cover Screw then remove the Terminal

Box Cover

2. Use the Terminal Box Cover to mark the position of screw holes

onto mounting surface. Drill the wall to depth of about 30 mm

and ﬁt the plastic plugs, and then ﬁx the Cover to the mounting

surface with rightly screws. Be careful to avoid drilling or screwing

into concealed electrical wiring.

3. Connecting the Power Cable (H05RN-F 3G 1mm², not included) to

the Terminal Block, see the relative symbol. Ensure the cable must

pass through the Cable Gasket.

4. Fit the lamp body to the Terminal Box Cover. Adjusting the light

direction you desired, then tighten the screws.

5. Switch the main power on.

Important: loosen the lock nuts and screws and outdoor wall light

before making any adjustments.

4x30mm

90°

45° 45°

90°

142 mm

6x27mm

45° 45°

OFF

130° 130°

φ6mm

30mm

39.5mm

130°

H:2.5m

1min

5sec

0 2

6 8mm

UNDERSTANDING THE CONTROLS (referring to the

Figure)

ADJUSTING THE DURATION TIME: The length of time that remains

switched on after activation can be adjusted from (10±5) seconds to

(4±1) minutes. Rotating the TIME from (+) to (—) will reduce the

duration time. Note: Once the light has been triggered by the PIR

sensor any subsequent detection will start the timed period again

from the beginning.

ADJUSTING THE LUX CONTROL LEVEL: The Lux control module has a

built-in sensing device (photocell) that detects daylight and darkness.

The ( ) position denotes that the Floodlights can work at day and

night, and the ( ) position only work at night. You can set to ope-

rate the unit at the desired level by adjusting the LUX knob.

SETTING THE CONTROLS

1. Put the Lux control knob to light ( ) position, turn the wall

switch on and wait half a minute for the control circuit to stabilize.

At this stage ensure that the TIME control knob is set at minimum

(—). The light will now switch on and remain on for about 30

seconds (within 60 seconds).

2. Direct the sensor toward the desired area to be scanned by adjus-

ting the sensor.

3. Have another person move across the center of the area to be

scanned and slowly adjust the angle of the sensor until the unit

sensors the presence of the moving person, causing the Light to

switch on. (refer Figure).

4. Adjust time control to required setting.

5. To set the Lux level at which the Light will automatically switch

“on” at night, turn the LUX control knob from daylight to night. If

the Light are required to switch on earlier, e. g. Dusk, wait for the

desired light level, then slowly turn the LUX control knob towards

daylight while someone walks across the center of the area to be

detected. When the Light switch on, release the LUX control knob.

You may need to make further adjustments to achieve your ideal

light level setting.

TECHNICAL DETAILS:

Voltage:

Wattage:

Detection range:

Duration time:

Weatherproof:

Power Cable:

220-240 V ~ 50 Hz

2 ×6 ×0.5W LED

130º and Max. 8 meters

from (10±5) seconds to (4±1) minutes adjustable

IP44

3G, 1.0mm² ﬂexible cable

Product specificaties

Merk:	Qazqa
Categorie:	Verlichting
Model:	90501

Heb je hulp nodig?

Als je hulp nodig hebt met Qazqa 90501 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Verlichting Qazqa

Qazqa Delux Handleiding

15 November 2024

Qazqa Solo Handleiding

19 Augustus 2023

Qazqa 91527 Handleiding

16 Juli 2023

Qazqa 91378 Handleiding

16 Juli 2023

Qazqa RLX-1201 Infrared Sensor Instruction Handleiding

16 Juli 2023

Qazqa 88898 Handleiding

16 Juli 2023

Qazqa 91370 Handleiding

16 Juli 2023

Qazqa 90501 Handleiding

16 Juli 2023

Qazqa 89433 Handleiding

16 Juli 2023

Qazqa 90502 Handleiding

16 Juli 2023

Handleiding Verlichting

Nieuwste handleidingen voor Verlichting

LumenRadio CRMX Galileo MAX Handleiding

21 December 2024

Showtec Performer Fresnel 2200 DDT Handleiding

21 December 2024

Showtec AirDrive 2.4 IP Handleiding

21 December 2024

Bosch FSN 1400 Set Professional Handleiding

21 December 2024

Neewer VL66C Handleiding

18 December 2024

American DJ ENCORE LB15IP Handleiding

18 December 2024

American DJ ENCORE LP12IP Handleiding

18 December 2024

Wiesenfield UNI-LP-100 Handleiding

17 December 2024

Cateye Wearable mini SL-WA10 Handleiding

16 December 2024

Cateye Volt50 HL-EL460RC-REAR Handleiding

16 December 2024