Pyle SBA8A Handleiding

Pyle Subwoofer SBA8A

Lees hieronder de 📖 handleiding in het Nederlandse voor Pyle SBA8A (5 pagina's) in de categorie Subwoofer. Deze handleiding was nuttig voor 30 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/5
SBA8A
8” 600 Watts Low-Profile Active Amplified
Car Audio Subwoofer System
Suitable for Under-seat Installations
Questions? Issues?
We are here to help!
Phone: (1) 718-535-1800
Email: support@pyleusa.com
www.P USA.comyle
2www.Py U comle SA. 3
Introduction
With the SBA8A
high-powered subwoofer system to your audio system.
SBA8A features low pass crossovers, and a control for
adjusting the input sensitivity from 0.12V to 3.5V.
Both high level (speaker level) and low level (RCA type) inputs are present, making this a
universal solution for use with any head unit or other input source.
included. You can control the subwoofer level with the remote level control module.
Mounting the Subwoofer
A typical location is shown below:
3. Mark the location for mounting hole screws by positioning the cabinet where you wish to
install it. Make a small mark to identify the position and remove the unit. Thoroughly clean
the area you plan to attach the subwoofer, using a vacuum cleaner and press down on it
securely.
Control Panel and Features
1. POWER ON LED INDICATOR
2. PROTECT LED INDICATOR
3. PHASE SHIFT: Use this switch to help compensate for time alignment problems in the
from the listener than the other speakers in the system.
4. AUTO POWER ON: During ON mode, It’s not necessary to connect the remote cable if
you’re using the high level inputs. Do not function with the RCA inputs. On the contrary
while it is during AUTO POWER OFF mode that it needs remote cable connection to turn
on the unit.
5. LOW PASS FILTER:
BELOW the
frequency you set. If the rest of your system is weak on the mids, you may wish to set this
control relatively high. If the midrange is well vered by the rest of your system, you willco
probably want the subwoofer to only receive lower frequency signal.
6. BASS BOOST: The bass boost feature will increase the sound level the bass frequencies.
7. INPUT CGAIN ONTROL: After yo av stalled yu h e in our yst s em, turn this control to minimum.
Turn the head unit on (and the subwoofer will turn on via the remote connection).
Turn the head unit volume to about 2/3 full level. Slowly turn up the subwoofer input
gain control until you hear a small amount of distortion. Then reduce the level until the
distortion is completely gone. Leave the control at this setting.
8. REMOTE LEVEL CONTROL PORT: Attach the included remote level control to cotrol the
volume level of the subwoofer independently.
9. HIGH LEVEL (speaker level) INPUTS: If your head unit does not have RCA outputs, you
can use the speaker outputs for the audio source for the . Use the supplied c lSBA8A ab e
and co ec outnn t e th puts properly as shown in th co ectie nn on dia agr m in his t manual.
10. LOW LEVEL RCA INPUTS: Low level inputs are the recommended way to introduce the
audio signal to the subwoofer if RCA outputs are present on your head unit or other
signal source (such as a sound processor).
11. FUSE: NEVER
replace the fuse with a wire or coin.
12. POWER TERMINALS
www.P USA.comyle
4www.Py U comle SA. 5
Low Level Input Wiring
Low-level (RCA) input wiring is preferred for best audio performance.
M t tr r at bos unk o h ch ack nst ll ti ns will i a a o r uir a fo RCA ableeq e 15-20 ot c , w ile pic up trunkh k s
and under-seat installations will require a 6-12 foot RCA cable. Always use a high quality
cable.
NOTE: Do not connect BOTH the high level and low level inputs from your receiver to your
High Level Input Wiring
The high level input(s) should only be used when your receiver lacks RCA outputs.
If the RCA outputs are not present, connect the speaker outputs from the receiver to the
problems.
NOTE: Do not connect BOTH the high level and low level inputs from your receiver to your
Power Connections
Connect the ground terminal to the closest point on the chassis of the vehicle.
Keep this ground wire to less than 39” (100 cm) inlength. Use 8 gauge (or heavier) wire.
AUTO POWER ON
the head unit using 16 gauge (or heavier) wire. Connect an empty fuse holder within 18” (45
location. Then connect the fuse holder to the “BATT+” connection on the subwoofer rear
panel.
Remote Level Control Connection
Instal the remote control securely under the
dash or in a similar location where using it will
not distract the driver.
To REMOTE TURN-ON
terminal of head unit

Product specificaties

Merk: Pyle
Categorie: Subwoofer
Model: SBA8A

Heb je hulp nodig?

Als je hulp nodig hebt met Pyle SBA8A stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Subwoofer Pyle

Pyle

Pyle PW18SUBA Handleiding

5 November 2024
Pyle

Pyle PSSUB101 Handleiding

14 Juni 2024
Pyle

Pyle PLR38I Handleiding

24 Februari 2024
Pyle

Pyle PLRG23C Handleiding

24 Februari 2024
Pyle

Pyle PLND35 Handleiding

24 Februari 2024
Pyle

Pyle PLMG85 Handleiding

12 Juni 2023
Pyle

Pyle PLML50FB Handleiding

5 Juni 2023
Pyle

Pyle PLBS122 Handleiding

4 Juni 2023
Pyle

Pyle PPA12 Handleiding

3 Juni 2023
Pyle

Pyle PLML51DB Handleiding

31 Mei 2023

Handleiding Subwoofer

Nieuwste handleidingen voor Subwoofer

Deaf Bonce

Deaf Bonce Apocalypse ASA-4000.1 Handleiding

20 November 2024
Deaf Bonce

Deaf Bonce Apocalypse Atom 2000 PRO Handleiding

20 November 2024
JBL

JBL PSW-D115 Handleiding

20 November 2024
JBL

JBL PSW-D110 Handleiding

20 November 2024
JBL

JBL PSW-D112 Handleiding

20 November 2024
JBL

JBL Power P1224 Handleiding

20 November 2024
JBL

JBL Power P1220D II Handleiding

20 November 2024
JBL

JBL Power P1242 Handleiding

20 November 2024
JBL

JBL Power P1220 II Handleiding

20 November 2024
JBL

JBL Power P1020 II Handleiding

20 November 2024