Pyle PLML50FB Handleiding

Pyle Subwoofer PLML50FB

Lees hieronder de 📖 handleiding in het Nederlandse voor Pyle PLML50FB (18 pagina's) in de categorie Subwoofer. Deze handleiding was nuttig voor 55 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/18
AM/FM/MP3/USB/AUX Stereo Receiver, Single DIN,
30 Preset Memory Stations, LCD Display
with Remote Control (Black)
PLML50FB
Stereo Receiver Power Amplifier
www.PyleUSA.com
2
INSTALLATION
Preparation
The preparation kit is necessary to mount the radio on the dashboard, this kit is
available at electronics stores and car audio specialists, check the installation
kit before using it to make sure it is the right one for your vehicle.
INSTALL THE DEVICE
1. Lift the left or right top corner of the plastic outer trim ring then pull it out to
remove it.
2. Insert the two bracket keys into the left and right side of the chassis to
separate the chassis from the housing.
3. Install the mounting knob on the board. Check the opening size of the sliding
panel to be mounted. If the measurement is not large enough, carefully cut it
until it slips easily on the opening. Do not force the handle in the opening so
as not to bend it. Locate the series of dubbing tabs above, below and all sides
to be mounted. Completely insert it to the opening of the board, bend the
tabs as necessary towards outside to ensure it ts the board.
4. Slide the stereo into the opening in the dash, ensuring that the wires behind
are tucked and not pinched.
5. Follow the wiring diagram carefully. Verify you've connected them correctly.
Connect the unit to a 12 Volt power source with adequate ground.CAUTION!
6. Now that your wires are all completed, attach the front panel and turn theON
unit (the vehicle must be switched on). If the unit does not work, check the
calibration again until the problem is solved. With the new car stereo secured
into the bracket, all you need to do is plug the wiring harness back into the
stereo and put the assembly back into place.
7. Slide the stereo into the opening in the dash, ensuring that the wires behind
are tucked and not pinched. Sometimes this may take a few times when the
vehicle has a tight dash opening. Tuck the wires back into an opening behind
the unit.
8. Install the plastic outer trim ring
9. Snap all the pieces of trim back into place over the stereo. Double check that
all screws and trim pieces are securely in place.Try out the new stereo.
Turn the car power on again and play around with the stereo and its settings
to be sure everything is in working order.
www.PyleUSA.com 3
WIRING CONNECTIONS
HARDS FREE PUSH-TO-TALK
PUSH-TO-TALK
• Allows you to access SIRI GOOGLE voice or via Wireless BT.
• Your phone must support SIRI or GOOGLE voice. Once connected to BT, your
phone will ask for access to your contact list.
• Now you are ready to use PUSH-TO-TALK PUSH-TO-TALK. Press the icon.
You are ready to talk. Call "(CONTACT NAME)", the system will call without
having to use your phone.
CONTROL PANEL BUTTONS
15A
Front C utput(Left)R A O Front C utput( ight)R A O R
R A Oear RC utput(Left)
R A O Rear RC utput( ight)
EXternal MIC
SWC
AN RADIO ANTENNA JAT: CK
F-L:Front C utput(Left)R A O
F-R: R A O RFront C utput( ight)
R-L:R R A Oear C utput(Left)
R-R:R R A O Rear C utput( ight)
Power/speaker Connector
FUSE 15A
PRECAUTION
+12V DC
NEGATIVE
EARTH


Product specificaties

Merk: Pyle
Categorie: Subwoofer
Model: PLML50FB

Heb je hulp nodig?

Als je hulp nodig hebt met Pyle PLML50FB stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Subwoofer Pyle

Handleiding Subwoofer

Nieuwste handleidingen voor Subwoofer