Pyle PS1000 Handleiding

Pyle Receiver PS1000

Lees hieronder de ๐Ÿ“– handleiding in het Nederlandse voor Pyle PS1000 (5 pagina's) in de categorie Receiver. Deze handleiding was nuttig voor 39 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/5
Stage & Studio Power Sequence Conditioner
PS1000 - PS1200
Pro Audio AV Digital Power Sequencer Controller
with Voltage & Temperature Readout, Rack Mount
www.PyleUSA.com
1www.PyleUSA.com 2
CAUTION!
RISK OF ELECTRIC SHOCK. DO NOT OPEN
TO PREVENT ELECTRIC SHOCK DO NOT REMOVE TOP OR BOTTOM COVERS.
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
DISCONNECT POWER CORD BEFORE REMOVING BACK PANEL COVER
TO ACCESS GAIN SWITCH.
WARNING!
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.
MAGNETIC FIELD
CAUTION! Do not locate sensitive high-gain equipment such as preampli๎˜Ÿers or
tape decks directly above or below the unit. Because this ampli๎˜Ÿer has a high
power density, it has a strong magnetic ๎˜Ÿeld which can induce hum into
unshielded devices that are located nearby. The ๎˜Ÿeld is strongest just above and
below the unit. If an equipment rack is used, we recommend locating the
ampli๎˜Ÿer(s) in the bottom of the rack and the preampli๎˜Ÿer or other sensitive
equipment at the top.
WATCH FOR THESE SYMBOLS:
The exclamation point triangle is used to alert the user
to important operating or maintenance instructions.
The lightning bolt triangle is used to alert the user to
the risk of electric shock.
Introduction & Features
This amazing professional audio processor has a built-in high performance Micro
Controller for precise electrical timing. This unit provides clean ๎˜Ÿlters AC power
with built in two stage EMI ๎˜Ÿlter for each output. 8 channel cut-switch rear panel
American Standard outputs and 1 constant un-switched front panel.
Other voltage outputs: 1 DC 12 Volt. You can link more than 100 units together
with automatic master unit display. The display shows AC voltage, ambient
temperature, wiring and ground status all in real time. 8 Segment display for
step Time and various LEDs cover output, master, bypass, power, voltage and
sequence.
Front Panel Introduction
1. Outlet Sequence Power ON/OFF: Push up or down to start the sequence
switch or automatically one by one.ON OFF
2. LED For Sequence Power ON/OFF
3. DISPLAY WINDOW: Displays voltage or temperature (both in Fahrenheit &
Centigrade)
4. Temperature: Adjust the temperature slightly if the real display is di๎˜žerent
from the real one.
5. Mode Select: Button switch for Fahrenheit/Centigrade temperature or
Voltage display on the LED window.
6. BYPASS Switch: Push to make all the outlets work at one time. Can't be
adjusted by other control.
7. CH 1 Only: After starting the power sequence, control only the Ch1 or ON OFF.
8. One touch key and LED: ON/OFF Press to power . The LED indicates ON/OFF
the related outlet's status.
9. Choose the internal power sequence delay Internal delay time selector:
time: 0.5 seconds or 2 seconds.
10. USB Charge (5V/2A): Charge for Mobile phone (5VI2A) each.
11. Power switch for the assistance light: Power the light according to ON/OFF
the switch position.
12. Assistance light connector: BNC This is connector, it can supply 12V/0.5A
power, use a gooseneck light to connect.
13. Always Power Outlet: Assistant power outlet, connects to the AC input
directly, power always valid.
Rear Panel Introduction
1. Main power supply with standard American plug
2. Input Voltage Selective: Power Supply Switch at 115V/60Hz or 230V/50Hz
3. Power outlet can carry 15AMP (RMS) each outlet, Outlets OUT1-OUT8:
otherwise the unit is not safe.
4. Remote Control link: You can set a extra switch to replace the power switch
to achieve the long distance control.
5. LED for remote control: Indicates the unit status, use it with Remote control.
6. Many unit works via link, if you want to link next unit, the lower unit Link out:
should be connected here.
7. Many unit works via link, if you need to link up, then the upper unit Link in:
should be connected here.
www.PyleUSA.com
3www.PyleUSA.com 4
BlOCK DIAGRAM
Filter Schematic Diagram


Product specificaties

Merk: Pyle
Categorie: Receiver
Model: PS1000

Heb je hulp nodig?

Als je hulp nodig hebt met Pyle PS1000 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Receiver Pyle

Pyle

Pyle P3001AT Handleiding

5 December 2024
Pyle

Pyle PLMRMBT5B Handleiding

5 December 2024
Pyle

Pyle Pro PTAU23 Handleiding

23 Augustus 2024
Pyle

Pyle PLAM2001D Handleiding

24 Februari 2024
Pyle

Pyle PT1100 Handleiding

24 Februari 2024
Pyle

Pyle PFA100 Handleiding

24 Februari 2024
Pyle

Pyle PDA35BT Handleiding

24 Februari 2024
Pyle

Pyle PHDA6BT Handleiding

18 December 2023
Pyle

Pyle PDA77BU Handleiding

18 December 2023
Pyle

Pyle PT865BT Handleiding

13 December 2023

Handleiding Receiver

Nieuwste handleidingen voor Receiver