Pyle PMA82 Handleiding

Pyle Windmeter PMA82

Lees hieronder de 📖 handleiding in het Nederlandse voor Pyle PMA82 (1 pagina's) in de categorie Windmeter. Deze handleiding was nuttig voor 29 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/1

PMA82 to measure ai temperature r

PMA82 Anemometer.T PMA82 Anemometer Congratulations on your purchase of the he

Introduction

measures air velocity in five uni of measure: feet per minute (ft/min), meters pe sec ts r

-ond (m/sec), miles per hour (MPH), kilometers per hour (km/hr), & nautical miles pe hour r

(knots)&CFM(ft /min). An internal sensor allows

or Fahrenheit units.

This meter is

service.

Meter Description

1. Vane sensor

2. LCD display

3. Units/°F/°C key

4. Ma Min x/ key

5. Hold key

Note: Battery compartment is on rear of unit

MAX MIN

V EL

�

123

Display

1. MAX MIN Record mode

2. Temperature display

3. Temperature units

4. Velocit units y

5. MAX or MIN mode

6. Velocit displ y ay

7. Low battery indicator

CFM

provide years of reliable

shipped fully tested and calibrated

and withproper

6. On/Off Key

PMA82

INSTRUCTION MANUAL

UNITS

MAX

MIN

shuts off after 15 minutes to conserve battey energy.

Operation

Meter Power

1. Press the P ER bu on to turn the meter on. the display does not switch on, check OW tt If

that a fresh 9V ba ery is installed. tt

2. Press the POWER button to turn the meter off.

3. The meter is equipped with an AUTO POWER OFF feature. The meter automatically

Measuring Air Velocity and Temperature

1. Place the sensor in the air stream under test.

2. Read the Air Velocity and Tem rature measurements directly on the LCD. pe

3. To calculate Air Volume in CFM (cubic feet per minute) or CMM (cubic meters per

minute) refer to the ‘Useful Equations and Conversions’ section.

Selecting the Temperature unit of measure (

oC/oF)

Press and hold the UNITS key for 3 seconds to select the temperature unit of measure.

The meter will beep twice and the display will indicate the currently selected unit of

measure.

Selecting the Air Velocity unit of measure

Press the UNITS key to change the unit of measure for Air Velocity measurements. The

displa ill flect the cu ent selection. st tsy w re rr A li of measurement uni is printed in the

specifica ions la in this manual.t ter

Record and Recall MAX / Min Function

1. To begin capturing the Maximum (MAX) and Minimum (MIN) air velocity and

temperature readings, press the MAX/MIN key and the ‘RECORD’ icon will appear in

the displa y.

2. Now, use the MAX/MIN key to toggle the view from MIN to MAX to RECORD. The

‘MAX’ or ‘MIN’ will appear along with the recalled reading for convenience. In RECO RD

mode, the meter will display the cu ent reading but will continue to capture a rr MAX nd

MIN readings.

3. To return to normal operation, press and hold the MAX/MIN key for 3 seconds to clear

and stop M /MIN recording. The meter will beep twice and the ‘M ’/‘MIN’ and AX AX

‘REC RD’ icons ill itch off.O w sw

Area Set for CFM

-Turn off the meter

-Press the HOLD key and hold

-While holding the HOLD key turn on the meter.It will now be in area set mode

“set area” will display.The area range can be set from 0 to 999.9ft

-Press the MAX/MIN key to shift the radix point(decimal point).

-Press the HOLD key to shift between flashing digits

-Press the UNITS key to change the value of the flashing digit

-After setting the area for CFM(inputting the square footage of the duct0,the

operator must turn the meter off,then turn the meter on again.At this point,

the meter will be set to read CFM for the desired area.

knots (nautical miles per hour) 1.94 - 48.5 knots 0.1 knots ± (3% + 0.4 knots)

mph (miles per hour) 2.24 -56.0 mph 0.1 mph ± (3% + 0.4 mph)

km/h (kilometers per hour) 3.6 - 90.0 km/h 0.1 km/h ± (3% + 0.8 km/hr)

m/s (meters per second) 1.00 - 25.00 m/s 0.01 m/s ± (3% + 0.20 m/sec)

ft/min (feet per minute) 196 - 4900 ft/min 1 ft/min ± (3% + 40 ft/min)

Max. 80% RH

32 °F to 122 °F (0 °C to 50 °C)

Dual function 8888 count LCD display

Maintenance

Battery Replacement

When the battery power falls low, the low battery icon will appear on the LCD. Replace

the 9V battery by removing the Phillips screw on the battery compartment door and

a e ing the ba ery compa en Ensure that the compartment cover is securely cc ss tt rtm t.

fastened when finished.

Cleaning and Storage

Wipe the meter and vane with a damp cloth as needed. Do not apply abrasive, solvents, or

other cleaners to the surface of the meter or vane. Store with the ttery removed and ba

avoid extreme temperature and humidity.

Specifications

Circuit description Custom LSI microprocessor design

Display

Measurement units m/s, km/h, min, knots , mph, Temperature: ft/ oC/oF

Data hold Freezes reading on the display

Sensor Structure Air velocity senso Conventional twi ed vane arm with low-r: st

friction ball-bearing

Memory Recall Record and Recall Maximum/Minimum (MAX/MIN) readings

A Power off uto After 15 minutes with disable feature

Operating Temperature

Op ating Humidity er

Power Supply 9V battery

Power Consumption Approx. 8.3mA DC

Air Velocity Range Specifications

Measurement Range Resolution A uracy cc

(% of reading)

Temperature Range Specifications

ycaruccA noituloseR egnaR

32oF to 122oF (0oC to 50oC) 0.1 oF (0.1oC) ± 4.0 oF (2

oC)

CFM

Air Flow Range Specifications

Unit Range Resolution Area

CFM(cubic feet per minute) 0-999,900ft /min 0.1 0.000-999.9ft

in Celsius

use will

Product specificaties

Merk:	Pyle
Categorie:	Windmeter
Model:	PMA82
Kleur van het product:	Zwart
Gewicht:	250 g
Soort:	Sonisch
Stroombron:	Batterij/Accu
Automatisch uitschakelen:	Ja
Beeldscherm:	LCD
Vormfactor:	Aflegvlak/hand-held
Meeteenheid temperatuur:	F, °C
Accu/Batterij voltage:	9 V
Nauwkeurigheid:	3 procent
Ondersteund aantal accu's/batterijen:	1
Inclusief monitor:	Ja
Windsnelheid meting bereik:	- m/s
Windsnelheid meting eenheid:	ft/s, km/h, kn, m/s, mph