Pyle PLMRA630BT Handleiding

Pyle Receiver PLMRA630BT

Lees hieronder de 📖 handleiding in het Nederlandse voor Pyle PLMRA630BT (27 pagina's) in de categorie Receiver. Deze handleiding was nuttig voor 68 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/27

Elite Series Waterproof Amplifiers

Warnings

If the unit is likely to undergo excess vibration through use, your must properly install the unit securely. Damage

caused by insufficient support is not covered by the warranty. To prevent damage to the unit's panels, always

use protective plastic cups or washers before tightening mounting bolts.

PLEASE NOTE: Users must ensure that any type of smoke and related substances are not allowed to

enter the amplifier. Smokey air is corrosive and prolonged exposure will cause irreparable damage to

your amplifier. Take precaution before reconnecting to a power supply. Be aware that when any

equipment is taken from a cold to humid location, condensation may occur inside. Always allow time

for the equipment to attain the same temperature as its environment before reconnecting to a

power supply.

• Read these instructions and keep them for future reference.

• Carefully follow instructions and follow directions carefully.

• Keep the amplifier dry, as some liquids may contain minerals that corrode electronics circuitry.

• Clean amplifier housing only with a slightly damp cloth. No chemicals or solutions.

• Do not block any of the ventilation openings. Install in accordance with the manufacturer's instructions.

• Do not install near any heat source such as radiators, stoves, or other electrical devices that produce heat.

• Prevent any cables, wired or power cord from being walked on, bent, stretched or pinched, particularly at

the plug or at the point where connects to the amplifier.

• When uncertain about specifications, please first consult the Pyle Audio website and see the FAQs.

• Ensure this unit is placed on a stable and flat surface and can accommodate the weight of this unit.

• Unplug this unit during lightning storms or when it is unused for an extended period of time.

• Do not leave this device unattended when powered on.

• Refer all servicing to qualified service personnel. Servicing is required when the device has been damaged

or malfunctions in any manner. This would include damage to he power supply cord or plug. t

Service may be obtained from an authorized Pyle Audio service center. Contact Pyle Audio and

make sure you have a receipt as proof of purchase along with the defective unit. You will be then

instructed to send or deliver the malfunctioning unit to an authorized center. They will handle the

necessary paperwork and repair. Remember to transport your unit in the original factory packaging.

Elite Series Waterproof Amplifiers

Testing & Connections

After all the connections have been made. turn on your stereo and listen for the

amplifier to turn on. If there are any unusual noises from the speakers then turn

the system off and recheck all the wiring.

After you have connected your radio or equalizer to the amplifier, you may adjust the gain

control to match the output level of your radio:

(A) Set the volume control on your radio to 2/3 position.

(B) Adjust the gain control for an average listening level.

(D) Start your vehicle and listen for electrical noise.

(E) Making fine adjustments to the sensitivity can reduce background noise and some

engine noise.

(F) CAUTION: Never turn the sensitivity up any farther than you need to get clear sound at

2/ 3 volume.

(G) This adjustment only needs to be made once.

NOTE: CARE MUST BE TAKEN AGAINST BATT - ERY OVER DISCHARGE CAUSED BY LONG OPERATION Of

THE SET AT A HIGH SOUND LEVEL WHEN THE ENGINE IS NOT RUNNING OR IDLING.

Maintenance

After all the connections have been made. turn on your stereo and listen for the amplifier

to turn on. If there are any unusual noises from the speakers then turn the system off and

recheck all the wiring.

Keep the amplifier dry. If it gets wet, wipe it dry immediately. liquids can contain minerals that corrode

electronic circuits.

Use the amplifier only in normal temperature environments. Temperature extremes of heat or cold

can shorten the life of electronic devices and distort or melt plastic parts.

Handle the amplifier gently and carefully. Dropping it can damage circuit boards and cases and can

cause the amplifier to work improperly.

Keep the amplifier away from dust and dirt. which can cause premature wear of parts.

Wipe the amplifier with a damp cloth occasionally to keep it looking new. Do not use harsh

chemicals, cleaning solvents, or strong detergents to clean the amplifier.

Product specificaties

Merk:	Pyle
Categorie:	Receiver
Model:	PLMRA630BT
Kleur van het product:	Blauw
Breedte:	276.86 mm
Diepte:	497.8 mm
Hoogte:	68.58 mm
LED-indicatoren:	Ja
Aan/uitschakelaar:	Ja
Connectiviteitstechnologie:	Bedraad en draadloos
Volumeregeling:	Draaiknop
Bedoeld voor:	Boot
Audio-uitgangskanalen:	- kanalen
Frequentiebereik:	15 - 30000 Hz
Signaal/ruis-verhouding:	100 dB
Aantal kanalen:	6 kanalen
Totale harmonische vervorming (THD):	0.05 procent
Input sensitiviteit:	250 mV
Piekvermogen per kanaal:	2000 W
Versterker klasse:	A/B
Speakers connectiviteit type:	RCA
Dynamisch vermogen per kanaal (2Ohm):	1700 W
Dynamisch vermogen uitvoer per kanaal(4 Ohm):	2000 W
RMS vermogen uitvoer per kanaal (4 Ohm):	900 W
Output impedance:	10000 Ohm
RMS vermogen uitvoer per kanaal (2 Ohm):	1500 W
Bass boost:	0 - 18 dB