Pureheat Odyssey Eco OE45W Handleiding

Pureheat Heater Odyssey Eco OE45W

Lees hieronder de 📖 handleiding in het Nederlandse voor Pureheat Odyssey Eco OE45W (2 pagina's) in de categorie Heater. Deze handleiding was nuttig voor 32 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

WARRANTY

DR Distribution guarantees that any part*, which we find to be defective in

materials or workmanship will be repaired or replaced free of charge for the

parts and any service labour for a period of 24 months for residential use and 12

months for commercial use from the date of purchase, as the original purchaser

of a Pureheat product, provided that all service be pre authorised by DR

Distribution.

• *The heater warranty does not cover service calls related to over- temperature

safety devices activating and shutting the heater down.

• *This Warranty does not cover failure due to accidental damage, misuse or

negligence, nor does it cover any consequential damages.

Important: If you are experiencing difficulties with the operation

or believe that your Pureheat heater is faulty in any way,

contact D R Distribution on

02 9618 3842

For the purpose of this warranty, it is a condition that the “wired in” models must

be installed by a registered electrical contractor and must be wired in

accordance with our wiring instructions. Similarly, this warranty becomes void if

the heater is serviced, repaired or altered by anyone other than D.R. Distribution

or its authorised Service Agents or if parts, other than approved parts, have been

used.

Record the date of purchase below and retain this card, together with your

purchase invoice for your own future reference.

The benefits conferred by this warranty are in addition to all other rights and

remedies which the consumer has under the Trade Practices Act and other

legislation.

OE – Series 2.4kW, 3.5Kw, 4.5kw

INSTALLATION INSTRUCTIONS

IMPORTANT:

All Odyssey-Eco heaters are designed for wall mounting only and must not be used

for any portable application.

• Wiring must be carried out by an authorised electrician in accordance with all

relevant Australian and local wiring standards.

• Before obtaining access to terminals, all supply circuits must be disconnected.

OE24 MODELS – c/w Flex & Plug:

1. Refer Odyssey Template & Installation Instructions enclosed separately with the heater.

2. If the supply cord is damaged, it must be replaced by the manufacturer, its service

agent or similarly qualified persons in order to avoid a hazard.

3. The heater must not be located in front of a socket-outlet

OE35 MODELS and OE45 – Hardwired:

1. Remove both plastic side vents by unscrewing the two recessed screws on each side.

2. Remove front panel by undoing the 2 screws on either side of the heater.

3. Bring all electrical supply wiring through the cable entry at the top left hand side of

the rear face.

4. The heater should be mounted a minimum of 50mm (2”) above the top of the floor or

oor covering.

Notes:

• The heater must not be recessed and should have a clearance on either side

and above the heater of at least 200mm to allow for unobstructed airflow.

• When selecting a position for the heater care must be taken not to position

the heater close to curtains and other combustible materials.

• The heater must not be located immediately below a socket- outlet.

5. For the quietest operation, firmly screw the unit onto the wall at all four mounting pad

points located in the corners at the back of the heater.

6. Care must be taken when mounting heater on the wall that no twisting of the unit

occurs. It may be necessary to pack the rear panel with washers to overcome this.

7. The heater must be connected to a fixed, single phase 240 volts a.c. supply, through

an isolating switch and in accordance with the relevant local regulations.

Notes:

• All connections must be tight.

• Do not use this heater with an external programmer, timer or any other

device that switches the heater on automatically, since a fire risk exists if the

heater is covered or positioned incorrectly.

• The heater must not be located in front of a socket-outlet

8. Replace front cover and tighten screws.

9. Fit the two side panels supplied loose with the heater. (Do not over tighten and distort

front panel).

10. Test heater, ensuring all facets of the unit’s operation are fully functional.

NAME:

ADDRESS:

PURCHASED FROM:

DATE OF PURCHASE:

MODEL NO:

SERIAL

NO:

INSTALLED BY: DATE:

PUREHEAT

D R Distribution Pty Ltd

Unit 9 No 3 Lancaster St Ingleburn NSW 2565

Ph 02 9618 3842

www.drdistribution.com.au

OPERATING INSTRUCTIONS

The PUREHEAT “Odyssey” is a fan assisted heater.

FAN- ASSISTED HEATING

The heater is fitted with a thermostat which controls the fan. The internal thermostat

senses the temperature of the air in the room and automatically switches the internal

heating elements and fan from high to off depending on the room temperature.

The heater may also incorporate a 24-hour programmable timer (OE24TW & OE35TW

Models), which enables the Fan Heater to be preset to operate at given time/s.

Turn the heater on at the main switch located in the middle of the top panel (fig. 1).

Once on, the switch is illuminated. Note: Ensure timer is placed in the “ON” position. (See

Timer section below – fig. 3).

(fig. 1 – Main Control Switch) (fig. 2 – Heat Control

Knob)

Adjustment of the thermostat:

To achieve the lowest possible running costs the following method of adjusting the

thermostat (fig. 2) should be followed. Turn the Heat Control Knob to the position marked

“Hi”.

When the room reaches the desired temperature rotate the Heat Control Knob anti-

clockwise until you hear the thermostat click. Leaving the thermostat at this setting will

ensure that the heater will continue to maintain this temperature as a minimum setting,

assuming the heater has been sized correctly for the room, .i.e. approximately 1 kW of

electric heating for every 10 square metres of floor area, assuming standard ceiling height

& insulation. The heater will heat with full element, then cut off depending upon the heat

requirements of the room at this particular thermostat setting.

Operating the 24hr timer.

To set the correct time on the Timer (fig. 3), turn the outer ring of tags until the clock face

reads the correct time. Note: this is a 24 hour clock so ensure the small white arrow head

on the outer clock face is pointing to the correct hour of the 24 hour time period around

the outer perimeter of the timer face.

(fig. 3 – Timer)

Push the sliding switch this now activates – on the face of the timer to the central position

the timer ready to accept your timed period/s. Note: with this switch pushed to the OFF

position “O”, the heater will not operate but the timer will continue to keep the correct

time.

With the switch pushed to the ON position “I”, the heater will run under normal

thermostatically controlled conditions but with no timing facility.

To set your required “Turn on/Turn off” time periods, push the total quantity of tabs

outwards from the centre of the timer face for the period you want the heater to operate.

Each tab is 15 minutes.

Over the 24-hour period the heater will operate for the time periods with the tabs pushed

outwards and not operate when the tabs are pushed inwards.

IMPORTANT NOTES

• The appliance is not intended for use by persons (including children) with

reduced physical, sensory or mental capabilities, or lack of experience and

knowledge, unless they have been given supervision or instruction concerning

use of the appliance by a person responsible for their safety.

• Young children should be supervised to ensure that they do not interfere with the

appliance.

• The motor in your heater may -be slightly noisy during the running in period. Any

undue noise usually disappears within the first ten to fourteen days of operation.

Should motor noise persist, consult the electrician who installed your heater.

• Warning in order to avoid overheating do not cover the heater

• Never place articles such as clothing, curtains or furniture etc. directly in front of the

heater, over the side corners of the heater, or stand immediately in front of the heater

when it is operating

• In accordance with current Approval Regulations, this heater is fitted with an

automatic, r- -resettable ove temperature cut out, which will shut the heater off if the

air ow is impeded.

If this occurs, ensure the grills are clear of any obstruction, turn the heater off and wait

5 minutes to allow the cut- out to reset.

After waiting 5 minutes, turn the heater on and the thermostat knob to the “High”

position.

If the heater still does not operate or blows cold air, the secondary Thermal-fuse has

activated and you will require a Service call to replace this device. Note: Such service

calls are not covered by .warranty

• The heater is not suitable for installation in a bathroom

CLEANING

Note: Before any cleaning is carried out on the heater be sure to turn the power off at the

isolating switch and turn all heater top console switches to the off position.

• External surfaces: The heater can be wiped over with a cloth or sponge dampened

with warm water or any spray on, non-abrasive, liquid cleaner.

Warning: Do not pour liquids directly onto the heater surfaces.

• Air outlet: The air outlet surfaces can be wiped clean using a cloth or sponge

dampened with warm water or any spray on, non- abrasive, liquid cleaner.

Important: The mesh air outlet grill should be vacuumed regularly using a brush type

nozzle to remove all dust and lint from the grill / air outlet area.

Arrow head

Sliding Switch

Timer

Off

Tabs

Product specificaties

Merk:	Pureheat
Categorie:	Heater
Model:	Odyssey Eco OE45W

Heb je hulp nodig?

Als je hulp nodig hebt met Pureheat Odyssey Eco OE45W stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Heater Pureheat

Pureheat Odyssey Eco OE24TW Handleiding

26 Augustus 2023

Pureheat Odyssey Eco OE45TW Handleiding

24 Augustus 2023

Pureheat Odyssey Eco OE35W Handleiding

24 Augustus 2023

Pureheat Odyssey Eco OE35TW Handleiding

24 Augustus 2023

Pureheat Odyssey Eco OE24W Handleiding

24 Augustus 2023

Pureheat Odyssey Eco OE45W Handleiding

24 Augustus 2023

Handleiding Heater

Nieuwste handleidingen voor Heater

Trisa 9330.44 Handleiding

18 December 2024

Hortus 211-413 Handleiding

18 December 2024

Yamazen HF-L122 Handleiding

18 December 2024

Yamazen HF-D121 Handleiding

18 December 2024

Yamazen HF-L121 Handleiding

18 December 2024

Universal Blue UCRA9104-24 Handleiding

18 December 2024

Orava VL-203 Handleiding

18 December 2024

SHX HL20OSZ Handleiding

16 December 2024

Stanley ST-125T-KFA-ES Handleiding

16 December 2024

Perel PHS2000 Handleiding

14 December 2024