Pulsar AWT682 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Pulsar AWT682 (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 5 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
INSTRUKCJA MONTAŻU/ASSEMBLY INSTRUCTIONS
POLSKI/ENGLISH
Kod / code: AWT468, AWT682, AWT8161820, AWT8172430
Nazwa/ Name: TRZ 40/U1/U2 TRZ 60/U1/U2 TRZ 80/U1/U2/U3* , ,
IU-TRAFO TRZ
Wydanie: 12 z dnia 6.2006.0 24
Zastępuje wydanie: 11 z dnia 11.04.2019
* -/U1/U2,U3= napi ęcie wtórne
-/U1/U2,U3= condary voltage* se
PL
1. Opis techniczny.
1.1. Przeznaczenie.
Transformator przeznaczony jest , U2 lub U3. AWT xxx do zasilania urządzeń wymagających napięcia AC: U1
Moc odbiorników dołączonych do zacisków transformatora nie może przekroczyć jego mocy znamionowej.
W celu zachowania wymaganej klasy szczelności (IP43) transformator należy montować w pozycji
pionowej zgodnie z rysunkiem rys.1 /rys.2.
1.2. Schemat elektryczny.
1.3. Opis . złącz i elementów transformatora
Element
Opis
L-N
z a pierwotnego, zasilania ~230 Å‚Ä…cze uzwojeni V
COM- - - U1 U2 U3
z , łącze uzwojenia wtórnego napięcia wyjściowe
FUSE
bezpiecznik topikowy w obwodzie zasilania (~230 V)
t
bezpiecznik termiczny 130°C (niepowracalny)
2 . . Montaż
Transformator przeznaczony odpowiednie jest do montażu przez wykwalifikowanego instalatora, posiadającego
(wymagane i konieczne dla danego kraju) zezwoleni (ingerencji) w instalacje 230 oraz a i uprawnienia do przyłączania V
instalacje niskonapięciowe.
Ponieważ zaprojektowany jest do pracy ciągłej nie posiada wyłącznika zasilania, dlatego należy transformator
zapewnić właściwą ochronę przeciążeniową w obwodzie zasilającym. Należy także poinformować użytkownika o sposobie
odłącze od napięcia sieciowego (najczęściej poprzez wydzielenie i oznaczenie odpowiedniego bezpiecznika w nia zasilacza
skrzynce bezpiecznikowej). Instalacja elektryczna powinna być wykonana według obowiązujących norm i przepisów.
W celu zachowania wymaganej klas (IP43) y szczelności transformator należy montować w pozycji pionowej
zgodnie z rysunkiem rys.1 /rys.2.
3
2. Installation.
The safety transformer must be installed by a qualified installer, holding the relevant certificates, required and
necessary in the particular country for connecting (interfering with) the 230 systems and low-voltage installations. V
Because the transformer is designed for the continuous operation and is not equipped with ON/OFF switch, the
power supply line should have the appropriate overload protection. The user should be informed how to disconnect the
transformers from the mains (usually be means of the separate fuse in the fuse-box). The power supply installation
should conform to the applicable standards and law.
To maintain the required degree of protection class (IP43), transformer must be installed in a vertical position as
shown in Fig.1 / Fig.2.
The transformer should be installed indoors (controls cabinets, casings), where air humidity is
normal (RH=90% max. without condensation) and temperature in the range of - to +40 10°C °C.
Provide sufficient airflow around the transformer for convectional cooling.
Caution!
Prior to entering installation it is necessary to make sure if the voltage
in the 230 V circuit is disconnected.
1. Install the transformer at the selected place on the DIN rail with the adaptors: plain surface or (AWO466 for
TRZ40VA TRZ60VA AWO467 for TRZ50VA TRZ80VA÷ or ÷ ) and evacuate connection wires.
2. Supply conductors ~230 V should be connected to terminals of the transformer. 230 L-NV
3. Connect the output transformer to a device, using installed cables
Remarks: Connect required voltage U1 or U2 or U3 (secondary voltage) for the correct device. The power of
connected devices must not exceed the power of the transformer.
4. If necessary, make other connections required for the correct type of system / device.
Remarks: consistent with requirements and recommendation of the producer.
5. Start the system (switch on ~230 , adjust or configure: according to procedure of the producer system. V) ’s
3. Parametry techniczne / Technical data.
Tab 1.
PARAMETRY
TECHNICZNE
TECHNICAL
DATA
Napięcie zasilania
Power supply voltage
~230 V; 50 Hz
(-15%/+10%)
Napięcie wyjściowe
U1/U2/U3
Power supply voltage
U1/U2/U3
Tab. 2
Prąd wyjściowy nominalny
I1/I2/I3
Nominal output current
I1/I2/I3
Tab. 2
Zabezpieczenie przeciwzwarciowe i
przeciążeniowe
Short circuit and overload protection
Bezpiecznik / Fuse
Tab. 2
Zabezpieczenie termiczne
Thermal protection
130 (niepowracalne) °C
N -ressetable fuse 130on oC
Złącza podłączeniowe
Terminal block
AWG24 12 2,5mm÷2
Obudowa
Casing
PC/ABS
UL94- V0
Klasa szczelności IP
IP degree
IP 43
Temperatura pracy /
Klasa cieplna
Operating temperature /
Heat class
- 10ºC÷40ºC
Ta 40B
Wilgotność względna RH – max.
Relative humidity RH max. –
90 [%]
Wymiary (szer x wys x głeb)
TRZ 40/U1/U2 TRZ 60/U1/U2 ÷
Dimensions (W x H x D )
TRZ 40/U1/U2 Z 60/U1/U2 ÷TR
75 x 124 x 65 [mm] ( -2) +/
Rys./Fig. 1
Wymiary (szer x wys x głeb)
TRZ 50/U1/U2/U3÷ TRZ 80/U1/U2/U3
Dimensions (W x H x D )
TRZ 50/U1/U2/U3÷ Z 80/U1/U2/U3 TR
95 x 136 x 76 [mm] ( -2) +/
Rys./Fig. 2
Waga netto
TRZ 40/U1/U2 TRZ 60/U1/U2 ÷
Net Weight
TRZ 40/U1/U2 Z 60/U1/U2 ÷TR
1, [kg] 30÷1,40
Waga brutto
TRZ 40/U1/U2 TRZ 60/U1/U2 ÷
Gross Weight
TRZ 40/U1/U2 Z 60/U1/U2 ÷TR
1, ] 40÷1,50 [kg
Waga netto
TRZ 50/U1/U2/U3 TRZ 80/U1/U2/U3 ÷
Net Weight
TRZ 50/U1/U2/U3÷ Z 80/U1/U2/U3 TR
1,60÷1,85 ] [kg
Waga brutto
TRZ 50/U1/U2/U3 TRZ 80/U1/U2/U3 ÷
Gross Weight
TRZ 50/U1/U2/U3÷ Z 80/U1/U2/U3 TR
1,65÷1,90 ] [kg


Product specificaties

Merk: Pulsar
Categorie: Niet gecategoriseerd
Model: AWT682

Heb je hulp nodig?

Als je hulp nodig hebt met Pulsar AWT682 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Pulsar

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd