Proficient C605 Handleiding


Lees hieronder de šŸ“– handleiding in het Nederlandse voor Proficient C605 (4 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 35 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
Before installing your LCR Ceiling Series speakers, you
should consider their placement carefully, taking into account
the location of electrical, plumbing and other ļ¬xtures. Contact
your Dealer for assistance if you are unsure of the best
location for your particular listening environment.
Placement In Ceiling: When placing your speakers into the
ceiling, they should be located so that the ļ¬xed 15Ėš angle
woofer is pointed towards the primary listening area.
If the speakers are positioned far away from the primary
listening area, simply adjust the pivoting tweeters so they are
pointed towards it.
Note: To avoid possible damage to the pivoting tweeters, read
the section entitled ā€œSPEAKER ADJUSTMENTSā€ in this manual
prior to performing the tweeter adjustment.
In a very large room with low ceilings, it may be necessary to
place additional speakers throughout the room. Contact your
Proļ¬cient Audio Systems Dealer for assistance.
New Construction - Unļ¬nished Ceilings
A Pre-Construction Bracket, available from your Dealer, may
be installed prior to drywall application across joists (up to 24"
on-center) where a speaker will be located. After the hole is
cut and the drywall is installed, the speakers are then easily
installed following the instructions for mounting in ā€œFinished
Ceilingsā€ below. If the speakers are to be mounted more Note:
than 24" on-center, a special ā€œExtra Long Wingā€ is available
from your Dealer.
Finished Ceilings
Prior to the actual installation of the speakers, it will be neces-
sary to run cables to the speaker locations. See your Dealer
for more information about cable installation. After the cable
has been properly installed, you are ready to mount the
speakers. Following the simple steps listed below will result in
a professional looking installation:
1. Determine the best area to mount your speakers. This area
of the ceiling should be free of obstructions such as electri-
cal conduit, HVAC ducts, or water lines. This can best be
determined by noting the placement of ļ¬xtures and gaining
access to an attic or crawl space for further analysis of the
location of such obstacles.
2. Find the joists nearest the desired speaker mounting loca-
tion. We highly recommend using a good stud-ļ¬nder tool
for this procedure. If you are lining up the speakers to some
other object or molding in the room, make sure you con-
sider the size of the bafļ¬‚e ļ¬‚ange which extends beyond the
mounting hole.
3. Mark the hole. A template for setting the hole is provided
in the box (along with two paint mask inserts for use when
painting). Position the template in the desired position and
pencil an outline on the ceiling.
4. Cutting the hole. CAUTION: This is the most important
part of the entire installation. If you are not certain
whether any obstructions exist behind the desired mounting
area, you should start by cutting a small hole in the center
of your penciled mounting hole with a drywall saw, cutting
at a 45Ā° angle towards the inside of the hole. (See Diagram 1)
Cutting the small hole at this angle will make drywall repair
much easier, using the piece cut out. Once you have deter-
mined that there arenā€™t any obstructions in your desired
mounting location, start cutting the ļ¬nished hole at a 90Ā°
angle to the ceiling surface.
5. Add insulation. If the area in the ceiling is not already insu-
lated, add an adequate amount insulation material to loosely
cover the back of the speaker. If the insulation material used
is faced with foil or paper, position the foil or paper away
from the speaker.
SPEAKER PLACEMENT
MOUNTING SURFACE PREPARATION
Diagram 1:
Ceiling Cut Out
OWNERā€™S MANUAL
LCR CEILING SERIES
C870 ā€¢ C660 ā€¢ C650
The LCR Ceiling Series speakers come from the factory with
the tweeter facing straight out from the bafļ¬‚e. This will result
in the overall smoothest response. However, depending on
your particular primary listening area, room acoustics, ceiling
height, or personal preference, you may ļ¬nd the sound more
pleasing by pointing the tweeters in a particular direction. If
additional treble is desired in the primary listening area, point
the tweeter towards that area; and if less treble is required,
point the tweeter away. Push gently at the edge of the tweeter
to point it in the desired direction. (See Diagram 3)
CAUTION:
Avoid touching metal dome tweeters, as damage may
occur (C870 & C660).
The unique integral four-foot mounting system incorporated
into each LCR Ceiling Series speaker allows for a quick
installation by following these easy steps:
1. Remove the grille. It may be necessary to push one or two
of the mounting screws and its attached foot towards the
bafļ¬‚e and against the inside surface of the grille to force
the grille out of its retaining groove.
2. Attach the speaker cable (observing the proper polarity
with your ampliļ¬er, + to + and ā€“ to ā€“). Make sure the left
channel of the ampliļ¬er is connected to the left speaker,
the right channel is connected to the right speaker, etc.
3. Make sure the mounting feet are turned inward to clear the
opening, and insert the speaker into the ceiling. Position
the speaker into the hole.
Note: The ļ¬‚ange of the speaker is designed to ļ¬‚ex and
conform to any small imperfections in the ceilingā€™s sur-
face. Tighten the four screws on the front of the bafļ¬‚e only
enough to make the ļ¬‚ange become snug against the ceiling.
As you tighten the screws, the feet will automatically ļ¬‚ip into
an outward position (See Diagram 2), thereby clamping the
drywall between the feet and the ļ¬‚ange. CAUTION: Over-
tightening may warp the bafļ¬‚e, crack the ceiling, cause
the ļ¬‚ange to distort, and make the grille difļ¬cult to
install.
4. Push the grille ļ¬rmly into the slot in the speaker bafļ¬‚e.
2
SPEAKER ADJUSTMENTS
SPEAKER INSTALLATION
Push Tweeter Here
Diagram 3:
Tweeter
Diagram 2:
Mounting Feet
Tweeter Adjustment :(C870 Only)
The switch labeled TREBLE allows for Ā±3dB of treble adjust-
ment. Your speakers were shipped with the treble switch in the
middle position, providing the most linear frequency response.
If you desire more treble, move the switch to the ā€œ+ā€ position,
and the tweeter will play 3dB higher. If you desire less treble,
move the switch to the ā€œā€“ā€ position, and the tweeter will play
3dB lower. To return to the neutral setting, push the switch
back to the middle position. (See Diagram 4)
Woofer Adjustment (C870 Only):
The switch labeled BASS allows for Ā±3dB of bass adjustment.
Your speakers were shipped with the bass set to the middle
position. This setting provides the ļ¬‚attest bass frequency
response. If you desire more bass, push the switch to the ā€œ+ā€
position and the bass will play 3dB higher. If you desire less
bass, push the switch to the ā€œā€“ā€ position and the bass will play
3dB lower. This setting provides a more linear bass frequency
response. To return to the neutral setting, push the switch back
to the middle position. (See Diagram 4)
Bass Adjustment Switch
Treble Adjustment Switch
Diagram 4:
Adjustment Switches
3
If you plan to paint your speakers, we recommend that it be
done prior to installation. If you plan to paint your speakers
sometime in the future, it is best to remove them by simply
reversing the steps for ā€œSPEAKER INSTALLATIONā€ above.
If it is necessary to paint the speakers when they are in
the ceiling, the paint masks provided in the carton must be
installed between the grille and ļ¬‚ange while they are being
painted with the ceiling.
Before painting your speakers, remove the material under
the grilles. Once the speakers have been painted, return the
material back into place.
Great care should be taken not to clog the holes of the grille,
as this will reduce the sound quality of the speakers.
Proļ¬cient Audio Systems recommends only light spray painting
using 5 parts thinning agent to 1 part paint.
PAINTING THE SPEAKERS
Proļ¬cient Audio Systems warrants to the original retail pur-
chaser that this product will be free from defects in only
materials and workmanship for a period of ten years, provided
the speaker was purchased from a Proļ¬cient Audio Systems
Authorized Dealer.
Defective products must be shipped, prepaid and insured,
together with proof of purchase, to the Proļ¬cient Audio
Systems Authorized Dealer from whom they were purchased,
or to Proļ¬cient Audio Systems at the address listed on this
installation instruction manual. Freight collect shipments will
be refused. It is preferable to ship this product in the original
shipping container to lessen the chance of transit damage. In
any case, the risk of loss or damage in transit is to be borne
by the purchaser.
If, upon examination at the Factory or Proļ¬cient Audio
Systems Authorized Dealer, it is determined that the unit was
defective in materials or workmanship at any time during this
warranty period, Proļ¬cient Audio Systems or the Proļ¬cient
Audio Systems Authorized Dealer will, at its option, repair or
replace this product at no additional charge, except as set
forth below. If this model is no longer available and can not
be repaired effectively, Proļ¬cient Audio Systems, at its sole
option, may replace the unit with a current model of equal or
greater value. In some cases where a new model is substi-
tuted, a modiļ¬cation to the mounting surface may be required.
If mounting surface modiļ¬cation is required, Proļ¬cient Audio
Systems assumes no responsibility or liability for such modiļ¬-
cation. All replaced parts and product become the property of
Proļ¬cient Audio Systems. Products replaced or repaired under
this Warranty will be returned to the original retail purchaser,
within a reasonable time, freight prepaid.
This Warranty does not include service or parts to repair dam-
age caused by accident, disaster, misuse, abuse, negligence,
inadequate packing or shipping procedures, commercial use,
voltage inputs in excess of the rated maximum of the unit, or
service, repair or modiļ¬cation of the product which has not
been authorized or approved by Proļ¬cient Audio Systems. This
Warranty also excludes normal cosmetic deterioration caused
by environmental conditions. This warranty will be void if the
Serial Number on the product has been removed, tampered
with or defaced.
This Warranty is in lieu of all other expressed warranties. If the
product is defective in materials or workmanship as warranted
above, the purchaserā€™s sole remedy shall be repair or replace-
ment as provided above. In no event will Proļ¬cient Audio
Systems be liable for any incidental or consequential dam-
ages arising out of the use or inability to use the product, even
if Proļ¬cient Audio Systems. or a Proļ¬cient Audio Systems
Authorized Dealer has been advised of the possibility of such
damages, or for any claim by any other party. Some states do
not allow the exclusion or limitation of consequential damages,
so the above limitation and exclusion may not apply.
All implied warranties on the product are limited to the duration
of this expressed Warranty. Some states do not allow limitation
on the length of an implied warranty. If the original retail pur-
chaser resides in such a state, this limitation does not apply.
LIMITED TEN-YEAR WARRANTY


Product specificaties

Merk: Proficient
Categorie: Speaker
Model: C605

Heb je hulp nodig?

Als je hulp nodig hebt met Proficient C605 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Speaker Proficient

Handleiding Speaker

Nieuwste handleidingen voor Speaker