Polar Look Kéo Power Handleiding
Polar
Fietstraineraccessoire
Look Kéo Power
Lees hieronder de 📖 handleiding in het Nederlandse voor Polar Look Kéo Power (2 pagina's) in de categorie Fietstraineraccessoire. Deze handleiding was nuttig voor 61 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/2
The Polar LOOK Kéo Power system calibrates itself automatically
each time the transmitters wake up and a receiving Polar device
is found. Calibration takes a couple of seconds.
Training temperature has an eect on the calibration
accuracy, so make sure your bike’s temperature has become
stable before you start the oset calibration.
Wake up the transmitters and turn on the training wait 1.
mode in your receiving Polar device to start the calibration.
Keep the bike upright and cranks in place until calibration 2.
is completed.
Complete the calibration as guided by your receiving device.3.
To ensure the calibration is done properly:
don’t put any weight on the pedals during calibration. »
don’t interrupt the calibration. »
If you’re unsure whether the calibration succeeded or the
temperature changes by more than 10 °C / 18 °F, do it again
manually.
You can start the manual calibration with your receiving device
also during a training session.
You can nd information on oset calibration with other than
Polar devices at www.polar.com/support.
Starting a training SeSSion
Wake up the transmitters and turn on the training wait 1.
mode in your receiving device. Let the system calibrate.
Start the training session with your receiving device to get 2.
information about power, cadence, eciency and pedaling
balance.
For more instructions, see the user manual of your receiving
device.
Stopping a training SeSSion
After you’ve stopped the training session with your receiving
device, the transmitters go to sleep after 90 seconds of inactivity.
Force Vector MeaSureMent
The Polar LOOK Kéo Power system comes with force vector
measurement. The feature enables the Polar training computer
to analyze your pedaling more precisely and helps you to learn
more ecient pedaling technique.
You can take the feature into use in the receiving device.
changing BatterieS
It’s recommended that you change both transmitter batteries at
the same time.
changing tranSMitter Sealing ringS
You received additonal sealing rings for the transmitters in the
product package.
Remove the old sealing rings carefully with tweezers. Place the
new sealing rings into the grooves on the transmitters. Handle
the transmitter with extra care.
Maintenance
Before every ride, check the pedals and cleats to be sure they
are free of dirt and that they are operating properly. Check your
cleats daily for excessive wear, and replace them if needed. Worn
cleats may come loose without noticing and cause you to crash.
Replace them only with genuine LOOK Kéo cleats. Do not drill,
paint or renish them. Keep pedals and cleats away from any heat
source. Spindle: LOOK spindles are subjected to a rotation test of
two million cycles at 100 revs / minute, with a load of 90 kg on the
pedal and o centered rotation (which creates an impact at each
rev). This test exceeds the toughest known standard EN 14781.
High pressure cleaners are not recommended.
technical SpeciFication
Kéo Power Transmitters
Battery type CR2354
Battery life 5 months (2 h/day, 7 days/week)
Operating temperature -10 °C to +50 °C / 14 °F to 122 °F
Storage temperature -20 °C to +60 °C / -4 °F to 140 °F
Material Aluminium, PA+GF
Water resistance IPX7 (splash proof)
LOOK Kéo Power Pedals
Operating temperature -10 °C to +50 °C / 14 °F to 122 °F
Storage temperature -20 °C to +60 °C / -4 °F to 140 °F
Distance crank/middle of the pedal 55 mm
Pedal oat 0 (black cleats), 4.5 (grey cleats), or 9
(red cleats) degrees
Water resistance IPX7 (splash proof)
Measurement ranges
Average power 0-2000 W
L/R balance 0-100%
Cadence 30-199 rpm
Maximum load 1800 N
oFFSet caliBration training iMportant inForMation
pedal tenSion adjuStMent
LOOK pedals are always delivered preset to a minimum tension.
You can adjust them with a 3 mm Allen key at the rear of
the pedal on the lever. By turning the key in the + direction
(clockwise), you increase the amount of stress necessary for cleat
release. Allow tension to remain minimal until you’ve become
perfectly familiar with the system. Adjustment can’t be carried
out when the cleat is engaged in the pedal. You will hear a “click”
when the maximum adjustment is reached. Once you hear the
click, stop screwing as it may damage the pedal.
engageMent / releaSe
Engagement: Insert the cleat in the pedal in accordance with
picture 1 and press down on the pedal to lock the cleat.
Release: Turn your heel outwards as in picture 2 and the cleat will
disengage. Do not tilt your foot towards the bike, as the heel may
touch the spokes and cause a crash.
1.
2.
Find product support at
www.polar.com/support/keo_power_sensor_
bluetooth_smart www.lookcycle.com and at .
Stay tuned with polar
Stay tuned with looK cycle
Manufactured by
Polar Electro Oy
Professorintie 5
FI-90440 KEMPELE
Tel +358 (0)8 5202 100
Fax +358 (0)8 5202 300
www.polar.com
LOOK Cycle International
27, rue du Dr Léveillé
CS 90013
FR-58028 NEVERS Cedex
Tel +33 (0)3 86 71 63 00
Fax +33 (0)3 86 71 63 10
www.lookcycle.com
17952253.00 ENG 05/2014
Polar look kéo Power
facebook.com/
polarglobal
youtube.com/
polar
twitter.com/
polarglobal
instagram.com/
polarglobal
LOOK Cycle
Lookcycletv
velolook
User Manual
English
The receiving device informs about the transmitters’ status but
there are also status led lights on transmitters.
Blinking magenta
The transmitter is awake but the transmitter has to be paired or
connected with a receiving device.
Blinking blue
The transmitter is connected to a receiving device. The oset
calibration has not been completed yet. Keep the bike upright
and cranks in place until calibration is completed.
Blinking green
The oset calibration has been
completed. You are ready for a
ride. The led is turned o while
pedaling to save battery.
Blinking red
Something has gone wrong. See
the receiving device for more
information.
The Polar LOOK Kéo Power system is compatible with
devices that support Bluetooth Smart technology and two
simultaneously connected power transmitters.
Visit www.polar.com/support for a list of compatible Polar
devices.
Using a Polar device allows you to get the most out of training
with analysis and follow-up tools in the Polar Flow web service.
Pair the transmitters with the receiving device before going for
your rst ride.
You can nd a device ID printed on the backside of the
transmitter. There’s a dierent device ID for each transmitter.
Rotate the cranks to wake up the transmitters.1.
Pair the power transmitters one at a time with the receiving 2.
device. See the user manual of the receiving device for
further instructions.
The power transmitters wake up automatically when the
cranks are rotated, and go to sleep after 90 seconds of
inactivity after a receiving device is no longer found.
introduction inStalling polar looK Kéo power led indicatorS pairing tranSMitterS with
receiVing deVice
Congratulations on your great purchase! In this handy guide we’ll
walk you through the rst steps in starting to use Polar LOOK Kéo
Power (with ® Smart), the innovative pedal-based cycling Bluetooth
system that helps you boost your performance and improve your
cycling technique.
Polar LOOK Kéo Power gives you detailed information about your
power output, left and right balance (depending on the set version)
and your cycling cadence and eciency. It works best with Polar
V650, state-of-the art bike computer for the most ambitious cyclists,
but it’s a great match also for many other Polar products and other
Bluetooth Smart compatible devices. To see the full list of compatible
Polar devices, go to > Products Accessories at www.polar.com.
You will benet even more from Polar LOOK Kéo Power when you
use it together with the Polar Flow web service. Plan your sessions,
get guidance to achieve your targets, analyze results and enjoy your
achievements with other training fans just like you.
what’S in the Box?
In the product box you’ll nd LOOK Kéo Power pedals and cleats, and Polar Power transmitters. Pedal installation tools,
spacers, sealing rings and other important small pieces also come with the product. Depending on the product version, the set includes
either one or two transmitters. Please note that the Essential version´s right and left spindles are not identical.
You can nd the latest version of this user manual, support material and videos at www.polar.com/support.
You can also nd user manual, support material and videos at .www.lookcycle.com
10:45
34.8
SP [km/h]EED
114
AL TUDE [m]TI
68.25
DISTANCE [km]
132
00:32:15
100%
It’s is important that you follow the installation instructions
carefully to get accurate measurement.
coMpatiBility checKliSt
Before installing the system, check that the product is compatible
with your bike.
Make sure that:
the chain clearance is at least 5 mm when the chain is »
on the outer chainring and the smallest pinion.
the cranks are less than 16 mm thick »
the cranks are less than 40 mm height »
the cranks have standard 9/16 x 20 BSA threading. »
inStalling BatterieS
Turn the battery cover counterclockwise to open it.1.
Place a battery (CR2354) inside the cover with the positive 2.
(+) side facing the cover.
Put the cover back in place. Turn the cover clockwise to close 3.
it.
Repeat for both transmitters.4.
Mounting pedalS
To install the pedals, you will need a thin 18 mm wrench, an 8
mm Allen key and the pedal installation tool (provided in product
box).
Clean the crank contact surfaces and threads to avoid 1.
damage.
If there’s a groove on the crank or if the cranks are made 2.
of carbon bre, place a spacer onto the pedal axle so that
metal touches metal (picture 1). If you are unsure, mount the
pedals with a spacer.
Tighten the pedal onto the crank. Make sure the pedal axle 3.
does not stick out (picture 2) and the mark on the pedal axle
points downwards when the crank points forward (picture 2).
Place the pedal installation tool into the pedal axle so that its 4.
shaft is in line with the crank (picture 3).
Hold the tool in place and tighten the pedal locknut with a 5.
18 mm wrench (picture 4). The recommended tightening
torque is 35 Nm / 25.8 lbf-ft.
Repeat for both pedals.6.
The left pedal (marked with a line on the axle) has left-hand
threads and needs to be installed counterclockwise. The
right pedal has right-hand threads and needs to be installed
clockwise.
inStalling tranSMitterS
Remove the protective cap from the transmitters.1.
Place a transmitter into the pedal axle. Make sure the shape 2.
of the transmitter matches with the shape inside the pedal
axle (picture 1). Push the transmitter rmly but without too
much force to avoid damage.
Make sure the transmitter is positioned correctly (picture 2). 3.
Position it again if needed.
Pass a cable tie through the hole in the transmitter. Keep 4.
the transmitter in place and tighten the cable tie around the
crank (picture 2). Cut o excess ends.
Repeat installation for both transmitters.5.
When rotating the cranks, make sure the transmitters do not 6.
hit any part of the bike or the chain while the chain is on the
largest crank gear and the smallest cassette gear.
The transmitters are marked with letters R (right) and L (left).
When the crank points forward, the transmitters should be
pointing down (picture 2).
1. 1.2.
2.
3. 4.
5 mm
Product specificaties
| Merk: | Polar |
| Categorie: | Fietstraineraccessoire |
| Model: | Look Kéo Power |
Heb je hulp nodig?
Als je hulp nodig hebt met Polar Look Kéo Power stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Fietstraineraccessoire Polar
18 Februari 2023
18 Februari 2023
Handleiding Fietstraineraccessoire
- Fietstraineraccessoire Garmin
- Fietstraineraccessoire Belkin
- Fietstraineraccessoire IHealth
- Fietstraineraccessoire Medisana
- Fietstraineraccessoire Wacom
- Fietstraineraccessoire Crivit
- Fietstraineraccessoire Koubachi
Nieuwste handleidingen voor Fietstraineraccessoire
6 Augustus 2023
15 Juni 2023
20 Mei 2023
28 April 2023
8 April 2023
29 Maart 2023
23 Maart 2023
5 Januari 2023
22 Oktober 2022