Planet ISW-801T Handleiding

Planet Niet gecategoriseerd ISW-801T

Lees hieronder de 📖 handleiding in het Nederlandse voor Planet ISW-801T (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 24 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

- 1 -

- 2 -

- 3 -

- 4 -

- 5 -

- 6 -

- 7 -

- 8 -

1. Package Contents

Thank you for purchasing PLANET Industrial Ethernet

Switch, ISW-501T/ISW-801T. In the following sections, the

term “Industrial Ethernet Switch” means the ISW-501T

or ISW-801T.

Open the box of the Industrial Ethernet Switch and carefully

unpack it. The box should contain the following items:

Industrial Ethernet

Switch x 1

User’s Manual x 1 RJ45 Dust

Cap x 5 (8)

DIN-rail Bracket w/

Screws x 1

Wall-mount Plate

w/Screws x 1 set

If any of these are missing or damaged, please contact

your dealer immediately; if possible, retain the carton

including the original packing material, and use them again

to repack the product in case there is a need to return it to

us for repair.

2.2 LED Indicators

LED Color Function

P1 Green Lit: indicates Power 1 has power.

P2 Green Lit: indicates Power 2 has power.

FAULT Green Lit: indicates either Power 1 or Power

2 has no power.

10/100

LNK/ACT Green

Lit: indicates the Switch is

successfully connecting to the

network at 100Mbps or 10Mbps.

O: indicates that the Switch is not

successfully connecting to the

network at 100Mbps or 10Mbps.

Blinking: indicates that the Switch is

actively sending or receiving data over

that port.

2.3 Switch Upper Panel

The upper panel of the Industrial Ethernet Switch consists

of one terminal block connector within two DC power

inputs.

2.6 Grounding the Device

Users MUST complete grounding wired with the device;

otherwise, a sudden lightning could cause fatal damage to

the device.

Max. fault loading: 24V, 1A

V1+ V2+

PWR1 PWR2Fault

DC Input: 12-48V

, 1.2A max.

AC Input: 24V

, 1.1A max.

1 2 3 4 5 6

Earth Ground

Note

EMD (Lightning) DAMAGE IS NOT CONVERED

UNDER WARRANTY.

2. Tighten the wire-clamp screws for preventing the wires

from loosening.

1 2 3 4 5 6

V1+ V1- V2+ V2-

Power 1 Power 2Fault

Note

1. The wire gauge for the terminal block should

be in the range between 12 and 24 AWG.

2. The power input range is DC 12V ~ 48V and

supports AC 24V.

3. Use one power input when using AC 24V.

2. Hardware Introduction

2.1 Switch Front Panel

The front panel of the Industrial Ethernet Switch consists of

Ethernet interfaces and LED indicators.

 Front View

P1 P2 Fault

10 /10 0

ACT

LNK

P1 P2 Fault

10/100

ACT

LNK

Figure 1: ISW-501T Front

View

Figure 2: ISW-801T Front

View

Figure 3 shows the upper panel of the Industrial Ethernet

Switch.

Max. fault loading: 24V, 1A

V1+ V2+

PWR1 PWR2Fault

DC Input: 12-48V

, 1.2A max.

AC Input: 24V

, 1.1A max.

1 2 3 4 5 6

Figure 3: ISW-501T and ISW-801T Top View

2.4 Wiring the Power Inputs

The Upper Panel of the Industrial Ethernet Switch indicates

a DC inlet power socket and consis of one terminal block ts

connector within 6 contacts. Please follow the steps below

to insert the power wire.

1. Insert positive/negative DC power wires into Contacts 1

and 2 for Power 1, or 5 and 6 for Power 2.

Max. fault loading: 24V, 1A

V1+ V2+

PWR1 PWR2Fault

DC Input: 12-48V

, 1.2A max.

AC Input: 24V

, 1.1A max.

1 2 3 4 5 6

2.5 Wiring the Fault Alarm Contact

The fault alarm contacts are in the middle of the terminal

block connector as the picture shows below. Inserting the

wires, the Industrial Ethernet Switch will detect the fault

status of the power failure, or port link failure and then

forms an open circuit. The following illustration shows an

application example for wiring the fault alarm contacts.

Fault Alarm Contacts

The Fault Alarm Contacts are

energized (CLOSE) for normal

operation and will OPEN when

failure occurs

Fault

Insert the wires into the fault alarm contacts

Note

1. The wire gauge for the terminal block should

be in the range between 12 and 24 AWG.

2. Alarm relay circuit accepts up to 24V, 1A

current (max.).

3. Installation

This section describes the functionalities of the Industrial

Ethernet Switch’s components and guides you to installing

it on the DIN rail and wall. Please read this chapter

completely before continuing.

Note

This following pictures show how to install the

device. However, the device in the picture is

not ISW-501T or ISW-801T.

3.1 DIN-rail Mounting Installation

3.2 Wall-mount Plate Mounting

- 9 -

- 10 -

- 11 -

- 12 - - 13 -

4. Product Specications

Model ISW-501T ISW-801T

Hardware Specications

10/100BASE-TX

Ports 5 8

LED Indicators

3 x LED for System and Power:

Green: DC Power 1

Green: DC Power 2

Green: Power Fault

1 x LED per Copper Port

Green: 10/100 LNK/ACT

Enclosure IP30-rated metal case

Dimensions

(W x D x H) 32 x 87 x 135mm

Weight 400g 428g

ESD Protection 6KV DC

Power

Requirements

12~48V DC, redundant power with

polarity reverse protection function,

24V AC power support

Power

Consumption/

Dissipation

1.6 watts/5.4BTU 2.1 watts/7.1BTU

Standards Conformance

Standards

Compliance

IEEE 802.3 Ethernet

IEEE 802.3u Fast Ethernet

IEEE 802.3x Full Duplex Flow Control

IEEE 802.3az Energy Ecient

Ethernet

Temperature Operating: -40~75 degrees C

Storage: -40~75 degrees C

Humidity Operating: 5% to 95%, Storage:

5% to 95% (non-condensing)

Regulatory

Compliance FCC Part 15 Class A, CE

Stability Testing

IEC60068-2-32 (free fall)

IEC60068-2-27 (shock)

IEC60068-2-6 (vibration)

Installation DIN-rail kit and wall-mount ear

Alarm

Provides one relay output for power

failure; Alarm relay current carry

ability: 1A @ DC 24V

Connector

Removable 6-pin terminal block

Pin 1/2 for Power 1; Pin 3/4 for fault

alarm; Pin 5/6 for Power 2

Switch Specications

Switch Processing

Scheme Store-and-Forward

Address Table 1K

Buer Memory Embedded 448K bits packet buer

Flow Control

Back pressure for half duplex,

IEEE 802.3x pause frame for full

duplex

Switch Fabric 1Gbps 1.6Gbps

Throughput (packet

per second) 0.74Mpps 1.19Mpps

5. Customer Support

Thank you for purchasing PLANET products. You can browse

our online FAQ resource at PLANET Web site rst to check

if it could solve your issue. If you need more support

information, please contact PLANET switch support team.

PLANET online FAQs:

http://www.planet.com.tw/en/support/faq

Switch support team mail address:

support@planet.com.tw

Contents are subject to revision without prior notice.

PLANET is a registered trademark of PLANET Technology Corp.

All other trademarks belong to their respective owners.

PLANET TECHNOLOGY CORPORATION

e-mail: sales@planet.com.tw http://www.planet.com.tw

10F., No.96, Minquan Rd., Xindian Dist., New Taipei City, Taiwan, R.O.C. Tel:886-2- -2219 9518 Fax:886-2-2219 9528-

EC Declaration of Conformity

For the following equipment:

*Type of Product : 5 -/8 Port 10/100TX Industrial Fast Ethernet Switch

*Model Number : ISW-501T, -8ISW 01T

* Produced by:

Manufacturer‘s Name : Planet Technology Corp.

Manufacturer‘s Address : 10F., No.96, Minquan Rd., Xindian Dist.,

New Taipei City 231, Taiwan, R.O.C.

is herewith confirmed to comply with the requirements set out in the Council Directive on the

Approximation of the Laws of the Member States relating to Electromagnetic Compatibility

Directive on (2014/30 U/E ).

For the evaluation regarding the EMC, the following standards were applied:

EN 55032 (2015 + AC:2016)

EN61000-3-2 (2014)

EN61000-3-3 (2013)

EN 55035 (2017)

Responsible for marking this declaration if the:

Manufacturer Authorized representative esta blished within the EU

Authorized representative established within the EU (if applicable):

Company Name: Planet Technology Corp.

Company Address: 10F., No.96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan, R.O.C.

Person responsible for making this declaration

Name, Surname Kent Kang

Position / Title : Director

Taiwan

May 25 18, 20

Place

Date

Legal Signature

Product specificaties

Merk:	Planet
Categorie:	Niet gecategoriseerd
Model:	ISW-801T
Kleur van het product:	Blauw
Gewicht:	428 g
Breedte:	135 mm
Diepte:	87 mm
Hoogte:	32 mm
Materiaal behuizing:	Metaal
Internationale veiligheidscode (IP):	IP30
LED-indicatoren:	Ja
Certificering:	FCC, CE
Netwerkstandaard:	IEEE 802.3, IEEE 802.3u, IEEE 802.3x
Temperatuur bij opslag:	-40 - 75 °C
Luchtvochtigheid bij opslag:	5 - 95 procent
Rack-montage:	Nee
Redundante voeding:	Ja
Vermogenstoevoer inclusief:	Nee
Ophangsysteem voor aan de muur:	Ja
Power over Ethernet (PoE):	Nee
Stapelbaar:	Nee
Switchingcapaciteit:	1.6 Gbit/s
MAC-adrestabel:	1024 entries
10G support:	Nee
Datastroombeheer:	Ja
Switch type:	Unmanaged
Aantal basis-switching RJ-45 Ethernet-poorten:	8
Fast Ethernet (koperen) ports kwantiteit:	8
Switch-laag:	L2
Type basis-switching RJ-45 Ethernet-poorten:	Fast Ethernet (10/100)
Throughput:	1.19 Mpps
Full duplex:	Ja
Koperen ethernetbekabelingstechnologie:	10BASE-T, 100BASE-TX
Warmtedissipatie:	7.1 BTU/h
Auto-negotiation:	Ja
Stroomverbruik (typisch):	2.1 W
Bedrijfstemperatuur (T-T):	-40 - 75 °C
Relatieve vochtigheid in bedrijf (V-V):	5 - 95 procent
Code geharmoniseerd systeem (HS):	85176990
DIN rail bevestiging:	Ja
Store-and-forward:	Ja
MAC-adres zelfverouderende functie:	Ja
MAC-adres zelflerende functie:	Ja