Planet IPOE-162S Handleiding

Planet Schakelaar IPOE-162S

Lees hieronder de 📖 handleiding in het Nederlandse voor Planet IPOE-162S (4 pagina's) in de categorie Schakelaar. Deze handleiding was nuttig voor 10 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

- 1 -

- 2 -

- 3 -

- 4 -

- 5 -

- 6 -

- 7 -

- 8 -

1. Package Contents

Thank you for purchasing PLANET Industrial IEEE

802.3at Gigabit High Power over Ethernet Splitter, IPOE-

162S. The term used in this “802.3at PoE Splitter”

user’s manual refers to the IPOE-162S.

Open the box of the Industrial IEEE 802.3at Gigabit

High Power over Ethernet Splitter and carefully unpack

it. The box should contain the following items:

Industrial IEEE 802.3at Gigabit High Power over

Ethernet Splitter x 1

User’s Manual x 1

DIN Rail Kit x 1

 Wall Mount Kit x 1

If any of these are missing or damaged, please contact

your dealer immediately; if possible, retain the carton

including the original packing material, and use them

again to repack the product in case there is a need to

return it to us for repair.

Industrial Case / Installation

IP30 metal case protection

 DIN Rail and Wall-mount type

 Supports EFT protection of 6000 VDC for power

line

 Supports 6000 VDC Ethernet ESD protection

 -40 to 75 degrees C operating temperature

Note

PSE (Power Sourcing Equipment) is a

device (switch or hub for instance) that will

provide power in a PoE setup. Maximum

allowed continuous output power per such

device in IEEE 802.3af is 15.4W and in IEEE

802.3at is 25W.

PDs (Powered Devices), such as IP phones,

network cameras, wireless access points,

etc., are PoE-enabled terminals powered by

a PSE and thus consumes energy.

5. Product Outlook

Figure 1: Front panel of IPOE-162S

LED Indicators

LED Color Function

Power

Ready Green

Lights to indicate the port is receiving

48~56V DC in-line power and ready

for output

Network Cable

10/100/1000Base-T: 4-Pair UTP Cat.

5, 5e, 6 distance up to 100m (328ft)

EIA/TIA-568 100-ohm STP (100m)

Power over Ethernet

PoE Standard IEEE 802.3at High Power over

Ethernet

Number of device can

be powered

1 or 2 (Varies on device power

requirements; DC1 + DC2 cannot be

over 25 watts)

Standards Conformance

Standards Compliance

IEEE 802.3 10Base-T Ethernet

IEEE 802.3u 100Base-TX Fast

Ethernet

IEEE 802.3ab 1000Base-T Gigabit

Ethernet

IEEE 802.3at High Power over

Ethernet

Regulation Compliance FCC Part 15 Class A, CE

Stability Testing

IEC60068-2-32 (Free fall)

IEC60068-2-27 (Shock)

IEC60068-2-6 (Vibration)

Standards Conformance

Operating Temperature -40 ~ 75 degrees C

Storage Temperature -40 ~ 85 degrees C

Humidity 5 ~ 95% (non-condensing)

2. Product Features

Interface

2 RJ-45 interfaces

1-port PoE Power+ Data input

1-port Data output

2 DC out (4-pin Terminal Block)

Power over Ethernet Splitter

 Complies with IEEE 802.3at Power over Ethernet,

 Splits the 48~56V DC power over RJ-45 Ethernet

cable into 12 / 24V DC output

 Up to 1 non-IEEE 802.3at PoE device powered

 Auto-detects PoE IEEE 802.3at equipment and

protects devices from being damaged with incorrect

installation

 Adjustable two different output voltage options

(12V / 2A, 24V / 1A) to t various devices

 Distance up to 100 meters

3. Product Specications

Product IPOE-162S

Hardware Specications

Interface

“PoE (Power

+ Data)”

Input Port

1 x RJ-45 10/100/1000Base-T

“Data” Out

Port 1 x RJ-45 10/100/1000Base-T

DC Out Plug

Connector 1 removable 4-pin terminal block

Data Rate 10/100/1000Mbps

(vary on Ethernet device attached)

LED Indicator System: Power Ready x 1 (Green)

DIP Switch 12V DC / 24V DC output voltage

Power Input 802.3at PoE 48~56V DC

Power Output 12V / 24V DC, Max 2A (adjustable)

Dimensions

(W x D x H) 135 x 87.8 x 32 mm

Weight 421g

Enclosure IP30 metal case

Installation DIN rail kit and wall mount ear

ESD Protection 6KV DC

6. Hardware Installation

The following section describes the hardware features of

the IPOE-162S. Before connecting any network device

to the IPOE-162S, read this chapter carefully.

6-1 Before Installation

If there is no power socket in your network

environment, the IPOE-162S provides DC power for this

Ethernet Device conveniently and easily. The IPOE-162S

will separate the power and data out. It provides two

kinds of DC power output through its DIP switch and its

voltage and current shown below:

 12V DC / 2A

 24V DC / 1A

Figure 2: DIP Switch Outlook

4. Physical Dimensions

Top View Front View Side View

Mounting Kit

DIN-Rail Kit

Rear View

- 9 -

- 10 -

- 11 -

- 12 - - 13 - - 14 -

Hint

Please check the power requirements of

the device carefully, that is going to get the

power from IPOE-162S.

1. If the power requirement is higher

than the IPOE-162S can supply, current

overload might shut down the IPOE-162S

itself. Thus, it will also shut down your

device as well.

2. Please ensure the output voltage is

correct for remote device. Otherwise, it

will damage your remote device.

3. Forbid to switch on/off the Power DIP during

operation. Otherwise, it will damage your

IPOE-162S and remote device. If you

want to switch the output Voltage DIP,

please Plug OFF the “POE In” cable and

wait for 3 seconds until the POE LED

(Power) is completely OFF.

6-3 Wiring the Power Outputs

Please follow the steps below to insert the power wires.

Step 1: Please nd one terminal block connector within

two DC power outputs shown below:

1 V-

DC Output 1

DC Output 2

2 V-

3 V+

4 V+

Note

The wire gauge for the terminal block

should be in the range of 12 ~ 24 AWG.

Step 2: Insert the Negative / Positive DC wires into the

V– / V+ terminal; terminals 1 and 3 for Power

1; terminals 2 and 4 for Power 2.

6-2 4-pin Power Output Terminal Block

From top to down, there are Negative (V-), Negative

(V-), Positive (V+) and Positive (V+), and two sets of

DC power output contact.

Figure 3: DC Power Output Terminal Block Outlook

Note

Two DC outputs are sharing 12V 2A or 24V

1A, totaling 25W PoE output power, which

means that DC1 + DC2 cannot be over the

25W PoE output power. Otherwise, it might

cause the power output to malfunction or

damage.

Step 3: Connect the other point of DC power wires

to the power devices. Tighten the wire-clamp

screws for preventing the wires from loosening.

Maximum Output 25 Watts

Powered

Device 1

One Powered Device

Total Maximum

Output 25 Watts

Powered

Device

Powered

Device

Two Powered Device

Step 4: Install the terminal block on PLANET IPOE-

162S Splitter.

Step 5: Connect the network copper cable (RJ-45)

from the High Power Injector (PSE) and it will

provide power to PLANET IPOE-162S Splitter

and the IPOE-162S will separate the power

and data to the PDs (power devices). Please

see the Figure below:

Non-PoE

Device

802.3at

PSE

802.3at PoE+ Data in

Data Out

DC+

10/100/1000T Copper

Customer Support

Thank you for purchasing PLANET products. You can

browse our online FAQ resource on PLANET Web site

rst to check if it could solve your issue. If you need

more support information, please contact PLANET switch

support team.

PLANET online FAQ :

http://www.planet.com.tw/en/support/faq.php?type=2

Switch support team mail address :

support_switch@planet.com.tw

Contents are subject to revision without prior notice.

PLANET is a registered trademark of PLANET Technology Corp. All

other trademarks belong to their respective owners.

Product specificaties

Merk:	Planet
Categorie:	Schakelaar
Model:	IPOE-162S
Kleur van het product:	Zwart
Gewicht:	421 g
Breedte:	135 mm
Diepte:	87.8 mm
Hoogte:	32 mm
Materiaal behuizing:	Metaal
LED-indicatoren:	Ja
Bekabelingstechnologie:	10/100/1000Base-T(X)
Netwerkstandaard:	IEEE 802.3at
Temperatuur bij opslag:	-40 - 85 °C
Luchtvochtigheid bij opslag:	5 - 95 procent
Rack-montage:	Nee
Redundante voeding:	Ja
Ophangsysteem voor aan de muur:	Ja
Power over Ethernet (PoE):	Ja
RJ-45 uitgang ports:	1
Switchingcapaciteit:	- Gbit/s
MAC-adrestabel:	- entries
Switch type:	Unmanaged
Aantal basis-switching RJ-45 Ethernet-poorten:	1
Type basis-switching RJ-45 Ethernet-poorten:	Gigabit Ethernet (10/100/1000)
RJ-45 invoer ports:	1
Bedrijfstemperatuur (T-T):	-40 - 75 °C
Relatieve vochtigheid in bedrijf (V-V):	5 - 95 procent
Hoeveelheid Power over Ethernet (PoE) ports:	1
DC-uit-stekker:	Ja