Planet IMG-2100T Handleiding

Planet Niet gecategoriseerd IMG-2100T

Lees hieronder de 📖 handleiding in het Nederlandse voor Planet IMG-2100T (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 259 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

- 1 - - 2 - - 3 - - 4 -

1. Package Contents

Thank you for purchasing PLANET Industrial RS232/422/485

Modbus Gateways. The table below shows the models with the

number of serial ports:

Model Name Serial Port Ethernet Port Power Input DI/DO

IMG-2100T 1 x DB9 +

1 x 4-pin

terminal block

1 x 10/100TX

RJ45 DC 9~48V

or AC 24V

IMG-2105AT 1 x 100FX

SFP -

IMG-2200T 2 x DB9 2 x 10/100TX

RJ45 DC 12~48V

IMG-2400T 4 x DB9 

“Industrial Modbus Gateway” is used as an alternative name in

this Quick Installation Guide.

Open the box of the Industrial Modbus Gateway and carefully

unpack it. The box should contain the following items:

The Industrial Modbus Gateway x 1

Quick Installation Guide x 1 Wall Mounting Kit x 1

DIN-rail Bracket w/Screws x 1 Dust Cap (RJ45/SFP)

If any item is found missing or damaged, please contact your local

reseller for replacement.

2. Requirements

The Industrial Modbus Gateway provides remote login interface for

management purposes. The following equipment is necessary for

further management:

Workstations running Windows XP/2003/Vista/7/8/2008/10, MAC

OS X or later, Linux, UNIX, or other platforms are compatible

with TCP/IP Protocols.

Ethernet Port Connection

Workstations are installed with Ethernet NIC (Network Inter-

face Card)

Network cables

Use standard network (UTP) cables with RJ45

Use Multi-mode or Single-mode ber patch cord with LC

connector and 100BASE-FX SFP transceiver (IMG-2105AT

only).

The above PC is installed with Web browser

Note

It is recommended to use Internet Explorer 8.0 or

above to access the Industrial Modbus Gateway.

Note

If the Web interface of the Industrial Modbus Gateway

is not accessible, please turn off the anti-virus

software or firewall and then try it again.

3. Hardware Introduction

3.1 Front Panels

IMG-2100T IMG-2105AT IMG-2200T IMG-2400T

PWR1 PWR2 Fault

Reset

LNK/

ACT

Rx Tx

10/100TX

RS232

TxD+

RxD+

RS422/485

PWR1 PWR2 Fault

Reset

LNK/

ACT

Rx Tx

100FX

SFP

RS232

TxD+

RxD+

RS422/485

PWR1 PWR2 Fault

SYS

LNK/

ACT

LNK/

ACT

Rx Tx

RS232/422/485

P1 P3

PWR1 PWR2

I/O

Fault

Rx Tx Rx Tx

SYS

LNK/

ACT

LNK/

ACT

P2 P4

Modbus

RS232/422/485

3.2 Wiring the Power Inputs

The upper panel of the Industrial Modbus Gateway indicates a DC

inlet power socket and consists of one terminal block connector

within 6 contacts. Please follow the steps below to insert the power

wire.

1. Insert positive/negative DC power wires into Contacts 1 and 2

for Power 1, or for . Figures 3-1 to Contacts 5 and 6 Power 2

3-3 show PWR1 and PWR2 of the Industrial Modbus Gateway.

IMG-2100T/IMG-2105AT: 9~48V DC/24V AC

V1+ V2+ V2

PWR1 PWR2Fault

Max. fault loading: 24V, 1A

DC Input: 9-48V

, 1A max.

AC Input: 24V

, 0.5A max.

1 2 3 4 5 6

Figure 3-1: IMG-2100T/IMG-2105AT Upper Panel

IMG-2200T: 12~48V DC

V1+ V1- V2+ V2-

PWR1 PWR2Fault

DC Input:

12-48V , 1Amax.

1 2 3 4 5 6

Figure 3-2: IMG-2200T Upper Panel

4.2 Logging in to the Industrial Modbus Gateway

1. Use Internet Explorer 8.0 or above for Web browser and enter IP

address http://192.168.0.100 (the factory-default IP address)

to access the Web interface.

2. When the following dialog box appears, please enter the default

user name and password (or the password “admin” “admin”

you have changed before) as shown in Figure 4-2.

Default IP Address: 192.168.0.100

Default User Name: admin

Default Password: admin

Figure 4-2: Login Screen

3. After entering the password, the main screen appears as shown

in Figure 4-3.

Figure 4-3: Web Main Screen of Industrial Modbus Gateway

4. The Server Menu on the middle of the Web page lets you access

all the functions and statuses the Industrial Modbus Gateway

provides.

Now, you can use the Web management interface to continue the

Modbus Gateway management. Please refer to the user manual for

more.

Note

1. For security reason, please change and memorize

the new password after this first setup.

2. Only accept command in lowercase letter under

web interface.

IMG-2400T: 12~48V DC

1A@24V

V1+ V1- V2+ V2-

PWR1 PWR2Fault

DI1 DO0 DO1DI0 GNDGND

DC Input:

12-48V , 1Amax.

1 2 3 4 5 6

Figure 3-3: IMG-2400T Upper Panel

2. Tighten the wire-clamp screws for preventing the wires from

loosening.

1 2 3 4 5 6

V1+ V1- V2+ V2-

Power 1 Fault Power 2

Figure 3-4: PWR1 & PWR2 pins of terminal block.

Note

The wire gauge for the terminal block should be in the

range from 12 to 24 AWG.

3.3 Serial Port PIN Assignment

4. Web Login

4.1 Starting Web Management

The following shows how to start up the of the Web Management

Industrial Modbus Gateway. Note the Industrial Modbus Gateway is

congured through an Ethernet connection. Please make sure the

manager PC must be set to the same IP subnet address.

For example, the default IP address of the Industrial Modbus

Gateway is , then the manager PC should be set 192.168.0.100

to 192.168.0.x (where x is a number between 1 and 254, except

100), and the default subnet mask is 255.255.255.0.

Ethernet

PC/Workstation with Web Browser

IP Address:192.168.0.x

RJ45 UTP Cable

IMG Modbus Gateway

IP Address:192.168.0.100

Figure 4-1: IP Management Diagram

- 5 - - 6 - - 7 - - 8 -

5. Remote Telnet Login

5.1 Logging in to the Remote Command Line

Interface

The Industrial Modbus Gateway also supports Telnet for remote

management. You can use Telnet to open a terminal session over

one of the Ethernet ports. The Modbus Gateway asks for user

name and password for remote login when using Telnet; please use

the following default IP address, username and password for the

rst-time login.

Default IP Address: 192.168.0.100

Default Username: admin

Default Password: admin

You will be presented with a text menu displaying the Industrial

Modbus Gateway’s general settings, which you will be able to view

and modify. Please refer to User Manual for a description of the

available settings.

6. Getting Started with MB VCOM Utility

With MB VCOM Utility, you can easily search one or multiple IMG

device servers over the network from a remote location.

Ethernet

Serial bus

Serial Device 1

Serial bus

Serial Device 2

COM1 (Port1)

COM2 (Port2)

MB VCOM

6.1 Installation of MB VCOM Utility

The MB VCOM Utility can be downloaded from PLANET Web site.

Please locate and run the setup program and “mbgsetup.exe”

follow the on-screen instructions.

download link:

https://www.planet.com.tw/en/support/downloads?&method=keywo

rd&keyword=IMG&view=6#list

After installing, rebooting your workstation/PC is required.

Note

If you have difficulty in downloading or executing

MB VCOM Utility, turn off the firewall and anti-virus

software first.

6.2 Searching Modbus Gateway

First click and then click if Modbus “Add Device” “Search”

Gateway has access to network, as shown below.

7. Recovering Back to Default

 Conguration

 IP Address has been changed or admin

password has been forgotten -

To reset the IP address to the default IP address “192.168.0.100”

or reset the login username and password to default value,

press the hardware-based reset button on the bottom panel

for about 5 seconds. After the device is rebooted, you can log

in the management Web interface within the same subnet of

192.168.0.xx and default password. Be noted that all the previous

setups will be disappeared after the factory default reset is made.

PWR1 PWR2 Fault

Reset

LNK/

ACT

Rx Tx

10/100TX

PWR1 PWR2 Fault

Reset

LNK/

ACT

Rx Tx

100FX

SFP

Figure7-1: IMG-2100T/IMG-2105AT Hardware-based Reset Button

System Reset

Buzzer Reset

SYSTEM RESET

BUZZER RESET

Figure7-2: IMG-2200T/IMG-2400T Hardware-based Reset Button

8. Customer Support

Thank you for purchasing PLANET products. You can browse our

online FAQ resource on PLANET web site rst to check if it could

solve your issue. If you need more support information, please

contact PLANET switch support team.

PLANET online FAQs:

http://www.planet.com.tw/en/support/faq

Switch support team mail address:

support@planet.com.tw

IMG-210x_220x series User’s Manual:

https://www.planet.com.tw/en/support/download.php?&method=key

word&keyword=IMG&view=3#list

(Please select your Industrial Modbus Gateway model from the

Product Model drop-down menu)

Contents are subject to revision without prior notice.

PLANET is a registered trademark of PLANET Technology Corp.

All other trademarks belong to their respective owners.

Product specificaties

Merk:	Planet
Categorie:	Niet gecategoriseerd
Model:	IMG-2100T
Kleur van het product:	Blauw
Gewicht:	392 g
Breedte:	32 mm
Diepte:	87.8 mm
Hoogte:	135 mm
Stroomvoorziening:	9~48V DC / 24V AC, redundant power with reverse polarity protection
Internationale veiligheidscode (IP):	IP30
LED-indicatoren:	Ja
Montagewijze:	DIN-rail/wandmontage
Soort serieële aansluiting:	RS-232/422/485
Aantal Ethernet LAN (RJ-45)-poorten:	1
Certificering:	FCC 15 A, CE A, RoHS
RS-232 port:	1
Ethernet LAN, data-overdrachtsnelheden:	10, 100 Mbit/s
Netwerkstandaard:	IEEE 802.3, IEEE 802.3u
Ondersteunde beveiligingsalgoritmen:	SNMP, SNMPv2
Temperatuur bij opslag:	-40 - 85 °C
Web-gebaseerd management:	Ja
Bedrijfstemperatuur (T-T):	-40 - 75 °C
Relatieve vochtigheid in bedrijf (V-V):	5 - 95 procent
Code geharmoniseerd systeem (HS):	85176990
Besturings -en afbeeldingseenheid:	Nee