Planet GSD-504UP Handleiding

Planet Schakelaar GSD-504UP

Lees hieronder de 📖 handleiding in het Nederlandse voor Planet GSD-504UP (4 pagina's) in de categorie Schakelaar. Deze handleiding was nuttig voor 35 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

- 1 -

- 2 -

- 3 -

- 4 -

- 5 -

- 6 -

- 7 -

- 8 -

1. Package Contents

Check the following contents of your package:

GSD-504HP User's Manual

55V Power Adapter Power Cord Rubber Feet x 4

If any of these are missing or damaged, please contact your

dealer immediately; if possible, retain the carton including the

original packing material, and use them again to repack the

product in case there is a need to return it to us for repair.

 Switching

Hardware-based 10/100/1000Mbps, auto-negotiation and

auto MDI/MDI-X

Flow control for full duplex operation and back pressure

for half duplex operation

Integrates address look-up engine, supporting 2K absolute

MAC addresses

Automatic address learning and address aging

 Hardware

LED indicators for PoE ready/activity and LINK/ACT

One 55V DC power jack

Fanless design

3. Switch Front Panel

Figure 3-1 shows the front panel of the PoE Switch.

5PWR41 2

Uplink

PoE++ PoE+

PoE-in-Use

LNK ACT

10/100/1000

Legacy

Standard

Figure 3-1: Front Panel

Note

When choosing a location, please keep in mind the

environmental restrictions discussed in Chapter 8

-- Product Specifications.

Step 4: Connect your PoE Switch to network devices.

A. Connect one end of a standard network cable to

RJ45 port 5 on the front panel of the PoE Switch.

B. Connect the other end of the cable to a network

device, such as NVR, workstation or router.

Step 5: Connect your PoE Switch to PoE PD devices.

A. Connect one end of a standard network cable to

an RJ45 port (Choose from ports 1 to 4) on the

front panel of the PoE Switch.

B. Connect the other end of the cable to an 802.3af/

at/bt PD.

4 PoE IP Cameras

Power

PoE PoE PoE PoE

4-channel NVR

GSD-504UP

1000BASE-T UTP

PoE

1000BASE-T UTP with PoE

Power Line

PoE++ PoE++ PoE+ PoE+

5. Switch Rear Panel

Figure 5-1 shows the rear panel of the PoE Switch.

50-56V

Figure 5-1: Rear Panel

Power

Notice

1. The device is a power-required device, meaning

it will not work till it is powered. If your

networks should be active all the time, please

consider using UPS (Uninterrupted Power Supply)

for your device. It will prevent you from network

data loss or network downtime.

2. In some areas, installing a surge suppression

device may also help to protect your GSD-504UP

from being damaged by unregulated surge or

current to the GSD-504UP or the power adapter.

2. Product Features

 RJ45 Interface

5 10/100/1000BASE-T RJ45 ports

 Power over Ethernet

Complies with IEEE 802.3af/at/bt Power over Ethernet

end-span PSE

2 ports for IEEE 802.3bt PDs and 2 ports for IEEE

8020.3af/at PDs

Supports PoE power up to 90 watts for PoE port 1 to port

2, 30 watts for PoE port 3 to port 4

Each port supports 55V DC power to PoE PD

120-watt PoE budget

Auto detects PD

Circuit protection prevents power interference between

ports

Supports PoE in Standard and Legacy mode

4. LED Indicators

System

LED Color Function

PWR Orange Lights: Indicates the Switch has power.

The LED is shown on Port 5

Per 10/100/1000Mbps Port

LED Color Function

LNK Green

Lights: Indicates the link through that

port is successfully established at

10/10/1000Mbps.

Blinks: Indicates that the Switch is actively

sending or receiving data over that

port.

PoE-in-Use Port

LED Color Function

PWR Orange Lights: Indicates the port is providing 55V

DC in-line power.

6. DIP Switch

Standard/Legacy Mode

Standard To provide power to the PD devices that follow the

IEEE 802.3af/at/bt standard.

Legacy

To provide power to the PD devices that do not

fully follow the IEEE 802.3af/at/bt standard.

Besides, the Legacy mode supports PoH and Ultra

PoE.

7. Installing the Switch

This part describes how to install your PoE Switch and make

connections to it. Please follow the procedures:

Desktop Installation

To install the PoE Switch on desktop, simply follow the

following steps:

Step 1: Attach the rubber feet to the recessed areas on the

bottom of the PoE Switch.

Step 2: Place the PoE Switch on desktop near AC power

source for its power adapter.

Step 3: Keep enough ventilation space between the PoE

Switch and the surrounding objects.

Note

Cable Distance for Switch

The cable distance between the GSD-504UP and

PC/PD devices should not exceed 100 meters for

UTP/STP cable.

Note

Make sure the wiring is correct

Category 3/4/5 cable can be used for 10/100Mbps

operation. To reliably operate your network at

1000Mbps, you must use an unshielded twisted-

pair (UTP) Category 5/5e cable, or better data

grade cabling. While a Category 3 or 4 cable may

initially seem to work, it will soon cause data loss.

Step 6: Supply power to the PoE Switch.

A. Connect one end of the power core to the Switch.

B. Connect the power plug to a standard wall outlet.

When the PoE Switch receives power, the power LED should

remain solid orange.

- 9 -

- 10 -

- 11 -

- 12 - - 13 -

Wall-mounted installation

Step 1: Find the wall that you want the GSD-504UP to be

mounted on.

Step 2: Please refer to the picture below and screw the two

screws into the marked areas of the wall.

122

Step 3: Hang the GSD-504UP on the screws from the wall.

Step 4: Repeat step 6 for the desktop Installation of the

power supply to the GSD-504UP.

Note

Before mounting the device to the wall, please

check the location of the electrical outlet and the

length of the Ethernet cable.

Power

Requirements 55V DC, 2.8A

Surge

Protection

Dierence Mode: ±4KV;

Common mode: ±6KV

ESD Protection Contact 4KV; air 6KV

Power

Consumption Max. 136 watts, 464.05 BTU

Dimensions

(W x D x H) 168 x 93 x 32 mm

Weight 414g

Power over Ethernet

PoE Standard

IEEE 802.3at Power over Ethernet Plus/PSE

IEEE 802.3bt Power over Ethernet Plus Plus/

PSE

PoE Power

Supply Type

Port 1-2: End-span + Mid-span

Port 3-4: End-span

Power Pin

Assignment

Port 1-2: 4 pairs 1/2 (-), 3/6 (+) and

4/5 (+), 7/8 (-)

Port 3-4: 2 pairs 1/2 (-), 3/6 (+)

PoE Power

Output

Port 1-2: 90W max.;

Port 3-4: 30W max.

Total PoE

Power Budget 120 watts

8.ProductSpecications

Model

GSD-504UP

2-Port 10/100/1000T 802.3bt PoE + 2-Port

10/100/1000T 802.3at PoE + 1-Port Gigabit

Desktop Switch

Hardware Specications

Network

Connector

5 10/100/1000BASE-T RJ45 auto MDI/MDIX

ports

PoE Inject

Port

2 ports with 802.3bt PoE++ injector function

(Ports 1 to 2)

2 ports with 802.3af/at PoE+ injector

function (Ports 3 to 4)

LED Display

System: PWR (Orange)

Per PoE port: PoE (Orange, port 1 to port 4)

Ethernet port: LNK (Green)

Thermal Fan Fanless design

Switch

Architecture Store and Forward

MAC Address

Table

2K MAC address table with auto learning

function

Switch Fabric 10Gbps

Switch

Throughput 7.44Mpps @64 bytes

Jumbo Packet 9K bytes

Flow Control Back pressure for half duplex. IEEE 802.3x

pause frame for full duplex

Standard Conformance

EMI Safety FCC Part 15 Class A, CE

Standard

Compliance

IEEE 802.3 10BASE-T

IEEE 802.3u 100BASE-TX

IEEE 802.3ab Gigabit 1000BASE-T

IEEE 802.3x Flow Control and Back Pressure

IEEE 802.3af Power over Ethernet

IEEE 802.3at Power over Ethernet Plus

IEEE 802.3bt Power over Ethernet Plus Plus

Environment

Operating

Environment 0 ~ 50 degrees C

Storage

Environment -10 ~ 70 degrees C

Operating

Humidity 5 ~ 95%, relative humidity, non-condensing

Storage

Humidity 5 ~ 95%, relative humidity, non-condensing

9. Customer Support

Thank you for purchasing PLANET products. You can browse

our online FAQ resource on PLANET Website rst to check if it

could solve your issue. If you need more support information,

please contact PLANET support team.

PLANET online FAQs:

https://www.planet.com.tw/en/support/faq?method=category&c1=1

Support team mail address:

support@planet.com.tw

Contents are subject to revision without prior notice.

PLANET is a registered trademark of PLANET Technology Corp.

All other trademarks belong to their respective owners.

FCC Warning

This device has been tested and found to comply with

the limits for a Class A digital device, pursuant to Part 15

of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the

equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the

Instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential

area is likely to cause harmful interference in which case the

user will be required to correct the interference at his own

expense

CE Mark Warning

This is a Class A product. In a domestic environment, this

product may cause radio interference, in which case the user

may be required to take adequate measures.

WEEE Warning

To avoid the potential eects on the environment and

human health as a result of the presence of

hazardous substances in electrical and electronic

equipment, end users of electrical and electronic

equipment should understand the meaning of the crossed-out

wheeled bin symbol. Do not dispose of WEEE as unsorted

municipal waste and have to collect such WEEE separately.

Product specificaties

Merk:	Planet
Categorie:	Schakelaar
Model:	GSD-504UP
Kleur van het product:	Blauw
Gewicht:	414 g
Breedte:	168 mm
Diepte:	93 mm
Hoogte:	32 mm
LED-indicatoren:	Ja
Stroom:	2.8 A
Vermogensverbruik (max):	136 W
DC voltage input:	55 V
Certificering:	FCC Part 15 Class A, CE
Netwerkstandaard:	IEEE 802.3, IEEE 802.3ab, IEEE 802.3af, IEEE 802.3at, IEEE 802.3bt, IEEE 802.3u, IEEE 802.3x
Temperatuur bij opslag:	-10 - 70 °C
Luchtvochtigheid bij opslag:	5 - 95 procent
Auto MDI/MDI-X:	Ja
Power over Ethernet (PoE):	Ja
Switchingcapaciteit:	10 Gbit/s
MAC-adrestabel:	2000 entries
Switch type:	Unmanaged
Aantal basis-switching RJ-45 Ethernet-poorten:	5
Type basis-switching RJ-45 Ethernet-poorten:	Gigabit Ethernet (10/100/1000)
Throughput:	7.44 Mpps
Jumbo Frames ondersteuning:	Ja
Full duplex:	Ja
Warmtedissipatie:	464.05 BTU/h
Bedrijfstemperatuur (T-T):	0 - 50 °C
Relatieve vochtigheid in bedrijf (V-V):	5 - 95 procent
Code geharmoniseerd systeem (HS):	85176990
Totaal Power over Ethernet (PoE)-budget:	120 W
Jumbo frames:	9000
Store-and-forward:	Ja
Half-duplex:	Ja