Pioneer PRS-D4000F Handleiding

Pioneer Receiver PRS-D4000F

Lees hieronder de 📖 handleiding in het Nederlandse voor Pioneer PRS-D4000F (6 pagina's) in de categorie Receiver. Deze handleiding was nuttig voor 47 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/6

Setting the Unit <ENGLISH>

Thank you for purchasing this PIONEER

product. Before attempting operation, be

sure to read this manual.

In case of trouble

When the unit does not operate properly,

contact your dealer or the nearest autho-

rized PIONEER Service Station.

CAUTION

Never replace the fuse with one of greater

value or rating than the original fuse. Use

of an improper fuse could result in over-

heating and smoke and could cause dam-

age to the product and injury including

burns.

CAUTION

Do NOT install or use your Pioneer ampli-

fier by wiring speakers rated at 4 Ohm (or

lower) in parallel to achieve a 2 Ohm (or

lower) bridged mode (Diagram B).

Amplifier damage, smoke, and overheating

could result from improper bridging. The

amplifier surface could also become hot to

the touch and minor burns could result.

To properly install or use a bridged mode

for a two-channel amplifier and achieve a 4

Ω Ωload, wire two 8 speakers in parallel

with Left + and Right – (Diagram A) or use

a single 4 Ωspeaker. For a four-channel

amplifier, follow the speaker output con-

nection diagram for bridging as shown on

the back of your amplifier, and wire two 8

Ωspeakers in parallel to achieve a 4 Ωload

or use a single 4 Ωspeaker per channel.

If you have any questions or concerns,

please contact your local authorized

Pioneer dealer or call Pioneer customer

service.

WARNING

• Always use the special red battery and ground

wire [RD-223], which is sold separately. Connect

the battery wire directly to the car battery positive

terminal (+) and the ground wire to the car body.

• Do not touch the amplifier with wet hands.

Otherwise you may get an electric shock. Also, do

not touch the amplifier when it is wet.

• For traffic safety and to maintain safe driving

conditions, keep the volume low enough so that

you can still hear normal traffic sound.

• Check the connections of the power supply and

speakers if the fuse of the separately sold battery

wire or the amplifier fuse blows. Detect the cause

and solve the problem, then replace the fuse with

another one of the same size and rating.

• To prevent malfunction of the amplifier and

speakers, the protective circuit will cut the power

supply to the amplifier (sound will stop) when an

abnormal condition occurs. In such a case, switch

the power to the system OFF and check the

connection of the power supply and speakers.

Detect the cause and solve the problem.

• Contact the dealer if you cannot detect the cause.

• To prevent an electric shock or short-circuit

during connection and installation, be sure to

disconnect the negative (–) terminal of the battery

beforehand.

• Confirm that no parts are behind the panel when

drilling a hole for installation of the amplifier. Be

sure to protect all cables and important equipment

such as fuel lines, brake lines and the electrical

wiring from damage.

• DO NOT allow amplifier to come into contact

with liquids due to, for example, the location

where the amplifier is installed. Electrical shock

could result. Also, amplifier and speaker damage,

smoke, and overheating could result from contact

with liquids. In addition, the amplifier surface and

the surface of any attached speakers could become

hot to the touch and minor burns could result.

Diagram A - Proper

Ohm

Speaker

+ -

Ohm

Speaker

Pioneer

Amplifier

4 Ohm Bridged Mode

L+ R-

Diagram B - Improper

Ohm

Speaker

+ -

Ohm

Speaker

Pioneer

Amplifier

2 Ohm Bridged Mode

L+ R-

Before Using This Product <ENGLISH>

Published by Pioneer Corporation.

Publicado por Pioneer Corporation.

Printed in China

Impreso na China

<YRD5067-A/U> ES<KMINX> <05L00000>

BRIDGEABLE FOUR-CHANNEL

POWER AMPLIFIER

AMPLIFICADOR DE POTENCIA DE

CUATRO CANALES EN PUENTE

Owner’s Manual

PRS-D4000F

Manual del Propietario

PIONEER CORPORATION

4-1, MEGURO 1-CHOME, MEGURO-KU, TOKYO 153-8654, JAPAN

PIONEER ELECTRONICS (USA) INC.

P.O. Box 1540, Long Beach, California 90801-1540, U.S.A.

TEL: (800) 421-1404

PIONEER EUROPE NV

Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium

TEL: (0) 3/570.05.11

PIONEER ELECTRONICS ASIACENTRE PTE. LTD.

253 Alexandra Road, #04-01, Singapore 159936

TEL: 65-6472-7555

PIONEER ELECTRONICS AUSTRALIA PTY. LTD.

178-184 Boundary Road, Braeside, Victoria 3195, Australia

TEL: (03) 9586-6300

PIONEER ELECTRONICS OF CANADA, INC.

300 Allstate Parkway, Markham, Ontario L3R OP2, Canada

TEL: 1-877-283-5901

PIONEER ELECTRONICS DE MEXICO, S.A. de C.V.

Blvd.Manuel Avila Camacho 138 10 piso

Col.Lomas de Chapultepec, Mexico, D.F. 11000

TEL: 55-9178-4270

Gain Control

Adjusting the gain controls A and B will help match the output of the car stereo to the Pioneer

amplifier. Normally, set the gain controls to the NORMAL position. If the output is low, even

when the volume of the car stereo is turned up, turn these controls clockwise. If there is dis-

tortion when the volume of the car stereo is turned up, turn these controls counter-clockwise.

• If you only use one input plug, set the gain controls for speaker outputs A and B to the same position.

• When using with an RCA equipped car stereo (standard output of 500 mV), set to the NORMAL

position. When using with an RCA equipped Pioneer car stereo with max. output of 4 V or more,

adjust level to match the car stereo output level.

Power Indicator

The power indicator lights when the

power is switched on.

Input Select Switch

For two-channel input, slide this switch

to the left. For four-channel input, slide

this switch to the right.

Cut Off Frequency Control

If the LPF/HPF select switch is set to

LPF or HPF, you can select a cut off

frequency from 40 Hz to 120 Hz.

BFC (Beat Frequency Control)

Switch

BFC switch is on the bottom of the unit.

If you hear a beat while listening to an

AM broadcast with your car stereo,

change the BFC switch using a small

standard tip screwdriver.

Terminal Cover

Before setting up the unit, unfasten the

screws with a 4 mm hexagonal wrench

(not supplied) and remove the terminal

cover.

LPF (Low-Pass Filter)/HPF (High-Pass Filter) Select Switch

Set the LPF/HPF select switch as follows according to the type of speaker that is connected

to the speaker output connector and the car stereo system:

LPF/HPF Select Audio frequency range Speaker Remarks

Switch to be output Type

LPF (Left) * — 40 Hz to 120 Hz Subwoofer Connect a subwoofer.

OFF (Center) Full range Full range

HPF (Right) * 40 Hz to 120 Hz — Full range Use if you want to cut the

very low frequency range*

because it is not necessary

for the speakers you are

using.

* See the “Cut Off Frequency Control” section.

Input Switch

It is possible to input from a car stereo

external output (subwoofer output) or a

car stereo speaker output. When using

an external output (subwoofer output),

slide the switch to the left. For connec-

tion instructions, see the “Connection

Diagram” section. When using a speak-

er output, slide the switch to the right.

In this case, it is necessary to use the

supplied speaker input wire with RCA

pin cord. For details, see the “Using the

Speaker Input” section.

Connecting the Power Terminal

• Always use the special red battery and ground

wire [RD-223], which is sold separately. Connect

the battery wire directly to the car battery positive

terminal (+) and the ground wire to the car body.

1. Pass the battery wire from the

engine compartment to the interior

of the vehicle.

• After making all other connections to the

amplifier, connect the battery wire terminal of

the amplifier to the positive (+) terminal of

the battery.

2. Twist the battery wire, ground wire

and system remote control wire.

3. Attach lugs to wire ends. Lugs not

supplied.

• Use pliers, etc., to crimp lugs to wires.

4. Connect the wires to the terminal.

• Fix the wires securely with the terminal

screws.

WARNING

Failure to securely fasten the battery wire to the ter-

minal using the terminal screws could cause the ter-

minal area to overheat and could result in damage

and injury including minor burns.

Fuse (30 A)

Engine

compart-

ment

Interior of

the vehicle

Drill a 14 mm

hole into the

vehicle body.

Insert the O-ring rubber

grommet into the vehicle

body.

Twist

Positive terminal

GND terminal

Power terminal

Battery wire

System remote

control terminal

System remote

control wire

Ground wire

Fuse (30 A)

Battery wire

Ground wire

Lug

Connecting the Unit <ENGLISH>

CAUTION

• Disconnect the negative (–) terminal of the battery

to avoid the risk of short-circuit and damage to

the unit.

• Secure the wiring with cable clamps or adhesive

tape. To protect the wiring, wrap adhesive tape

around it where they lie against metal parts.

• Do not route wires where they will get hot, for

example where the heater will blow over them. If

the insulation heats up, it may become damaged,

resulting in a short-circuit through the vehicle

body.

• Make sure that wires will not interfere with mov-

ing parts of the vehicle, such as the gearshift,

handbrake or seat sliding mechanism.

• Do not shorten any wires. Otherwise the protec-

tion circuit may fail to work when it should.

• Never feed power to other equipment by cutting

the insulation of the power supply wire to tap

from the wire. The current capacity of the wire

will be exceeded, causing overheating.

• Never replace the fuse with one of greater value

or rating than the original fuse. Use of an improp-

er fuse could result in overheating and smoke and

could cause damage to the product and injury

including burns.

Speaker Channel Speaker Type Power

Four-channel Subwoofer Nominal input: Min. 75 W

Other than subwoofer Max. input: Min. 150 W

Two-channel Subwoofer Nominal input: Min. 300 W

Other than subwoofer Max. input: Min. 600 W

Three-channel Subwoofer Nominal input: Min. 75 W

Speaker output A Other than subwoofer Max. input: Min. 150 W

Three-channel Subwoofer Nominal input: Min. 300 W

Speaker output B Other than subwoofer Max. input: Min. 600 W

CAUTION:

To prevent damage and/or injury

• Do not ground the speaker wire directly or con-

nect a negative (–) lead wire for several speakers.

• This unit is for vehicles with a 12-volt battery and

negative grounding. Before installing it in a recre-

ational vehicle, truck or bus, check the battery

voltage.

• If the car stereo is kept on for a long time while

the engine is at rest or idling, the battery may go

dead. Turn the car stereo off when the engine is at

rest or idling.

• If the system remote control wire of the amplifier

is connected to the power terminal through the

ignition switch (12 V DC), the amplifier will

always be on when the ignition is on— regardless

of whether the car stereo is on or off. Because of

this, the battery could go dead if the engine is at

rest or idling.

• Speakers to be connected to the amplifier should

conform with the standards listed below. If they

do not conform, they may catch fire, emit smoke

or become damaged. The speaker impedance must

be 2 to 8 ohms. But in case of two-channel and

other bridge connections, the speaker impedance

must be 4 to 8 ohms.

• Install and route the separately sold battery wire

as far away as possible from the speaker wires.

Install and route the separately sold battery wire,

ground wire, speaker wires and the amplifier as

far away as possible from the antenna, antenna

cable and tuner.

• Cords for this product and those for other prod-

ucts may be different colors even if they have the

same function. When connecting this product to

another product, refer to the supplied Installation

manuals of both products and connect cords that

have the same function.

Connection Diagram

• This diagram shows connections using external output (subwoofer output). Slide the input switch to the left.

• When you connect with speaker output, connections defers from the diagram. For details, see the “Using the

Speaker Input” section. In either case, you need to set the input switch. For details, see the “Setting the Unit”

section.

Connecting the Speaker Output

Terminals

1. Expose the end of the speaker wires

using nippers or a cutter by about

10 mm and twist.

2. Attach lugs to speaker wire ends.

Lugs not supplied.

• Use pliers, etc., to crimp lugs to wires.

3. Connect the speaker wires to the

speaker output terminals.

• Fix the speaker wires securely with the termi-

nal screws.

Using the Speaker Input

Connect the car stereo speaker output

wires to the amplifier using the supplied

speaker input wire with RCA pin cord.

• Slide the input switch to the right.

• For four-channel input, connect two speaker

input wires with RCA pin cord to RCA input

jack A and B. Be sure to slide the input select

switch to the right.

• For two-channel input, connect the speaker

input wire with RCA pin cord to RCA input

jack A. Do not connect anything to RCA

input jack B. Be sure to slide the input select

switch to the left.

7Connections when using the speaker

input

• As a result of connecting the car stereo speaker

output wire to the amplifier, the power of the

amplifier is turned on automatically when the car

stereo is turned on. It is not necessary to connect

the system remote control wire in this case.

Note:

• Connect the system remote control wire when the

power of the amplifier is not to be turned on when

the car stereo is turned on.

10 mm

Twist

Speaker

output

terminal

Terminal screw

Speaker wire

Lug

Speaker wire

Grommet

RCA input

Special red battery wire [RD-223] (sold separately)

After making all other connections at the amplifier,

connect the battery wire terminal of the amplifier to

the positive (+) terminal of the battery.

Ground wire (Black) [RD-223] (sold separately)

Connect to metal body or chassis.

Amplifier with

RCA input jacks

Car stereo with

RCA output jacks

System remote control wire (sold separately)

Connect the male terminal of this wire to the system remote control terminal of the car stereo

(SYSTEM REMOTE CONTROL). The female terminal can be connected to the auto-antenna relay

control terminal. If the car stereo does not have a system remote control terminal, connect the male

terminal to the power terminal through the ignition switch.

Fuse (30 A)

Connecting wire with

RCA pin plugs (sold

separately).

Speaker output terminal

See the “Connecting the

Speakers and Input

Wires” section for

speaker connection

instructions.

Fuse (30 A) ×2

External Output

If only one input plug is used, do

not connect anything to RCA

input jack B.

RCA input jack B

RCA output jack

RCA input jack A

Speaker output

Speaker input

wire with RCA

pin cord

To RCA input

jack of this unit.

Car stereo

White: Black: Black: Red:

Left Left + ≠ Right Right ≠ +

Connecting the Unit <ENGLISH>

CAUTION

• Do not install in:

—Places where it could injure the driver or pas-

sengers if the vehicle stops suddenly.

—Places where it may interfere with the driver,

such as on the floor in front of the driver’s

seat.

• Make sure that wires are not caught in the sliding

mechanism of the seats, resulting in a short-cir-

cuit.

• Confirm that no parts are behind the panel when

drilling a hole for installation of the amplifier.

Protect all cables and important equipment such

as fuel lines, brake lines and electrical wiring

from damage.

• Install tapping screws in such a way that the screw

tip does not touch any wire. This is important to

prevent wires from being cut by vibration of the

car, which can result in fire.

• DO NOT allow amplifier to come into contact

with liquids due to, for example, the location

where the amplifier is installed. Electrical shock

could result. Also, amplifier and speaker damage,

smoke, and overheating could result from contact

with liquids. In addition, the amplifier surface and

the surface of any attached speakers could become

hot to the touch and minor burns could result.

• To ensure proper installation, use the supplied

parts in the manner specified. If any parts other

than the supplied ones are used, they may damage

internal parts of the amplifier, or they may

become loose causing the amplifier to shut down.

• Never replace the fuse with one of greater value

or rating than the original fuse. Use of an improp-

er fuse could result in overheating and smoke and

could cause damage to the product and injury

including burns.

CAUTION:

To prevent malfunction and/or injury

• To ensure proper heat dissipation of the amplifier,

be sure of the following during installation.

—Allow adequate space above the amplifier for

proper ventilation.

—Do not cover the amplifier with a floor mat or

carpet.

• DO NOT allow amplifier to come into contact

with liquids due to, for example, the location

where the amplifier is installed. Electrical shock

could result. Also, amplifier and speaker damage,

smoke, and overheating could result from contact

with liquids. In addition, the amplifier surface and

the surface of any attached speakers could become

hot to the touch and minor burns could result.

• Do not install the amplifier on unstable places

such as the spare tire board.

• The best location for installation differs with the

car model and installation location. Secure the

amplifier at a sufficiently rigid location.

• Make temporary connections first and check that

the amplifier and the system operate properly.

• After installing the amplifier, confirm that the

spare tire, jack and tools can be easily removed.

Example of installation on the floor

mat or on the chassis

1. Place the amplifier where it is to be

installed. Insert the supplied tapping

screws (4 ×18 mm) into the screw

holes. Push on the screws with a

screwdriver so they make marks

where the installation holes are to be

located.

2. Drill 2.5 mm diameter holes at the

point marked, and install the ampli-

fier, either on the carpet or directly

to the chassis.

Replacing the terminal cover

1. Align the unit and terminal cover,

and insert the screw.

2. Tighten the screw with a 4 mm

hexagonal wrench (not supplied).

Installation <ENGLISH> Specifications <ENGLISH>

Power source ........................................................................................................ 14.4 V DC (10.8 V to 15.1 V allowable)

Grounding system .......................................................................................................................................... Negative type

Current consumption .................................................................................................... 27.7 A (at continuous power, 4 Ω)

Average current drawn* ...................................................................................................... 10.4 A (4 Ωfor four channels)

20.2 A (4 Ωfor two channels)

20.2 A (2 Ωfor four channels)

Fuse ........................................................................................................................................................................ 30 A ×2

Dimensions .................................................................................................................... 304 (W) 56 (H) × × 202 (D) mm

Weight .................................................................................................................... 3.0 kg (Leads for wiring not included)

Maximum power output ............................................................................................ 150 W ×4 (4 ) / 600 W 2 (4 Ω × Ω)

Continuous power output .......................................................... 75 W 4 (at 14.4 V, 4 × Ω, 20 Hz to 20 kHz 1.0% THD)

300 W ×2 (at 14.4 V, 4 Ω, 1 kHz 1.0% THD)

150 W ×4 (at 14.4 V, 2 Ω, 1 kHz 1.0% THD)

Load impedance ................................................................................................................ to 8 ...... 4 Ω(2 Ω Ω allowable)

(Bridge connection: 4 Ωto 8 Ωallowable)

Frequency response ........................................................................................................ 10 Hz to 40 kHz (+0 dB, –3 dB)

Signal-to-noise ratio .................................................................................................................... 100 dB (IEC-A network)

Distortion ........................................................................................................................................ 0.005% (10 W, 1 kHz)

Separation .................................................................................................................................................... 70 dB (1 kHz)

Low pass filter ............................................................................................................ Cut off frequency: 40 Hz to 120 Hz

Cut off slope: –12 dB/oct

High pass filter .......................................................................................................... Cut off frequency: 40 Hz to 120 Hz

Cut off slope: –12 dB/oct

Gain control .................................................................................................................................... RCA: 400 mV to 6.5 V

Speaker: 1.6 V to 26 V

Maximum input level / impedance .................................................................................................... RCA: 6.5 V / 22 kΩ

Speaker: 26 V / 90 kΩ

Note:

• Specifications and the design are subject to possible modification without notice

due to improvements.

*Average current drawn

• The average current drawn is nearly the maximum current drawn by this unit

when an audio signal is input. Use this value when working out total current

drawn by multiple power amplifiers.

Connecting the Speakers and Input Wires

The speaker output mode can be four-channel, three-channel (stereo + mono) or two-channel

(stereo, mono). Connect the speaker leads to suit the mode according to the figures shown

below.

Four-channel

Three-channel

≠

≠≠

Two-channel (Stereo)

Two-channel (Mono)

≠

RCA input jack A

(Right)

Speaker out A

(Left)

RCA input jack B

Connecting wires

with RCA plugs

(sold separately)

From car stereo (RCA output)

If only one input plug is used, such as

when the car stereo has only one output

(RCA output), connect the plug to RCA

input jack A, but do not connect a plug to

RCA input jack B.

(Left)

Speaker out B

(Right)

RCA input jack A

(Right)

Speaker out A

(Left)

RCA input jack B

Connecting wires

with RCA plugs

(sold separately)

From car stereo (RCA output)

If only one input plug is used, such as

when the car stereo has only one output

(RCA output), connect the plug to RCA

input jack A, but do not connect a plug to

RCA input jack B.

Speaker out B

(Mono)

Input select switch is on the top of the unit. For two-

channel input, slide this switch to the left. For four-

channel input, slide this switch to the right.

RCA input jack A

In the case of two-channel mode

connect RCA plugs to the RCA

input jack A.

Speaker (Left)

Speaker (Right)

Connecting wire with

RCA plugs

(sold separately)

From car stereo (RCA output)

Speaker (Mono)

Connecting wire with

RCA plugs

(sold separately)

From car stereo (RCA output)

Input select switch is on

the top of the unit. Slide

this switch to the left.

RCA input jack A

In the case of two-channel mode

connect RCA plugs to the RCA

input jack A.

Input select switch is on

the top of the unit. Slide

this switch to the left.

Tapping-screws

(4 ×18 mm)

Floor mat

or chassis

Drill a 2.5 mm diameter hole

Screw

Terminal Cover

Input select switch is on the top of the unit. For two-

channel input, slide this switch to the left. For four-

channel input, slide this switch to the right.

Product specificaties

Merk:	Pioneer
Categorie:	Receiver
Model:	PRS-D4000F

Heb je hulp nodig?

Als je hulp nodig hebt met Pioneer PRS-D4000F stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Receiver Pioneer

Pioneer VSX-535 Handleiding

3 Mei 2024

Pioneer A-10EB Handleiding

12 Juli 2023

Pioneer VSX-531D-B Handleiding

4 Juli 2023

Pioneer DMH-342EX Handleiding

3 Juli 2023

Pioneer AVH-A215BT Handleiding

11 Juni 2023

Pioneer AVH-P6850DVD Handleiding

10 Juni 2023

Pioneer DMH-1770NEX Handleiding

6 Juni 2023

Pioneer VSXLX104 Handleiding

5 Juni 2023

Pioneer DEH-P2650 Handleiding

3 Juni 2023

Pioneer DMH-A5450BT Handleiding

21 Mei 2023

Handleiding Receiver

Nieuwste handleidingen voor Receiver

DAP Audio TA-4.3400 Handleiding

21 December 2024

Devialet Astra Dual Handleiding

19 December 2024

Devialet Astra Handleiding

19 December 2024

Atlas Sound T112 Handleiding

18 December 2024

Atlas Sound AL2430 Handleiding

18 December 2024

Atlas Sound AP-S15 Handleiding

18 December 2024

Atlas Sound AP-S15L Handleiding

18 December 2024

Atlas Sound AA-GPN1200 Handleiding

18 December 2024

Atlas Sound AA35 Handleiding

18 December 2024

Atlas Sound PA702 Handleiding

18 December 2024