Pioneer GM-X572 Handleiding

Pioneer Receiver GM-X572

Lees hieronder de 📖 handleiding in het Nederlandse voor Pioneer GM-X572 (8 pagina's) in de categorie Receiver. Deze handleiding was nuttig voor 43 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/8
Setting the Unit
Gain Control
If the sound level is too low, even when
the volume of the car stereo used along
with this power amplifier is turned up,
turn gain control on the front of the
power amplifier clockwise. If the sound
distorts when the volume is turned up,
turn the gain control counter-clockwise.
• When using with an RCA equipped car
stereo (standard output of 500 mV), set to
the NORMAL position. When using with
an RCA equipped Pioneer car stereo with
max. output of 4 V or more, adjust level to
match the car stereo output level.
• If you hear too much noise when using the
speaker input terminals, turn the gain
control counter-clockwise.
Power Indicator
The power indicator lights when the
power is switched on.
BFC (Beat Frequency Control) Switch
If you hear a beat while listening to an
AM broadcast with your car stereo,
change the BFC switch using a small
standard tip screwdriver.
Thank you for purchasing this PIONEER
product. Before attempting operation, be
sure to read this manual.
Composition of Manual
This manual applies to the GM-X972,
GM-X572 and GM-X372. However, the
illustrations show the GM-X972.
In case of trouble
When the unit does not operate properly,
contact your dealer or the nearest autho-
rized PIONEER Service Station.
WARNING
•Always use the special red battery and ground
wire [RD-223], which is sold separately. Connect
the battery wire directly to the car battery positive
terminal (+) and the ground wire to the car body.
•Do not touch the amplifier with wet hands.
Otherwise you may get an electric shock. Also, do
not touch the amplifier when it is wet.
•For traffic safety and to maintain safe driving
conditions, keep the volume low enough so that
you can still hear normal traffic sound.
•Check the connections of the power supply and
speakers if the fuse of the separately sold battery
wire or the amplifier fuse blows. Detect the cause
and solve the problem, then replace the fuse with
another one of the same size and rating.
•To prevent malfunction of the amplifier and
speakers, the protective circuit will cut the power
supply to the amplifier (sound will stop) when an
abnormal condition occurs. In such a case, switch
the power to the system OFF and check the
connection of the power supply and speakers.
Detect the cause and solve the problem.
•Contact the dealer if you cannot detect the cause.
•To prevent an electric shock or short-circuit
during connection and installation, be sure to
disconnect the negative (–) terminal of the battery
beforehand.
•Confirm that no parts are behind the panel when
drilling a hole for installation of the amplifier. Be
sure to protect all cables and important equipment
such as fuel lines, brake lines and the electrical
wiring from damage.
Before Using This Product
PIONEER CORPORATION
4-1, MEGURO 1-CHOME, MEGURO-KU, TOKYO 153-8654, JAPAN
PIONEER ELECTRONICS (USA) INC.
P.O. Box 1540, Long Beach, California 90801-1540, U.S.A.
TEL: (800) 421-1404
PIONEER EUROPE NV
Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium
TEL: (0) 3/570.05.11
PIONEER ELECTRONICS ASIACENTRE PTE. LTD.
253 Alexandra Road, #04-01, Singapore 159936
TEL: 65-6472-1111
PIONEER ELECTRONICS AUSTRALIA PTY. LTD.
178-184 Boundary Road, Braeside, Victoria 3195, Australia
TEL: (03) 9586-6300
PIONEER ELECTRONICS OF CANADA, INC.
300 Allstate Parkway, Markham, Ontario L3R OP2, Canada
TEL: (905) 479-4411
PIONEER ELECTRONICS DE MEXICO, S.A. de C.V.
San Lorenzo 1009 3er. Piso Desp. 302
Col. Del Valle Mexico, D.F. C.P. 03100
TEL: 55-5688-52-90
Published by Pioneer Corporation.
Copyright © 2002 by Pioneer Corporation.
All rights reserved.
Publicado por Pioneer Corporation.
Copyright © 2002 Pioneer Corporation.
Todos los derechos reservados.
Printed in U.S.A.
Impreso en los EE.UU.
<HRD0222-A> ES<KYMFX/02I00000>
BRIDGEABLE POWER AMPLIFIER
AMPLIFICADOR DE POTENCIA EN
PUENTE
Owner’s Manual
GM-X972
GM-X572
GM-X372
Manual del Propietario
LPF (Low-Pass Filter) Select Switch
Set the LPF select switch as follows according to the type of speaker that is connected to the
speaker output connector and the car stereo system:
LPF Select Audio frequency range Speaker Remarks
Switch to be output Type
LPF (left) Very Low Frequency range Subwoofer Connect a subwoofer.
OFF (right) Full range Full range
Connecting the Unit
CAUTION
•Disconnect the negative (–) terminal of the battery
to avoid the risk of short-circuit and damage to
the unit.
•Secure the wiring with cable clamps or adhesive
tape. To protect the wiring, wrap adhesive tape
around it where they lie against metal parts.
•Do not route wires where they will get hot, for
example where the heater will blow over them. If
the insulation heats up, it may become damaged,
resulting in a short-circuit through the vehicle
body.
•Make sure that wires will not interfere with mov-
ing parts of the vehicle, such as the gearshift,
handbrake or seat sliding mechanism.
•Do not shorten any wires. Otherwise the protec-
tion circuit may fail to work when it should.
•Never feed power to other equipment by cutting
the insulation of the power supply wire to tap
from the wire. The current capacity of the wire
will be exceeded, causing overheating.
GM-X972
Speaker Channel Speaker Type Power
Two-channel Subwoofer Nominal input: Min. 160 W
Other than subwoofer Max. input: Min. 300 W
One-channel Subwoofer Nominal input: Min. 460 W
Other than subwoofer Max. input: Min. 800 W
Connection Diagram
Fuse (30 A)
Grommet
Special red battery wire [RD-223] (sold separately)
After making all other connections at the amplifier,
connect the battery wire terminal of the amplifier to
the positive (+) terminal of the battery.
Ground wire (black) [RD-223] (sold separately)
Connect to metal body or chassis.
GM-X972: Fuse (30 A) ×2
GM-X572: Fuse (20 A) ×2
GM-X372: Fuse (25 A) ×1
Car stereo with
RCA output jacks
External Output
Connecting wires with RCA
pin plugs (sold separately).
RCA input jack
Speaker output terminal
See the Connecting the“
Speaker wires” section
for speaker connection
instructions.
System remote control wire (sold separately)
Connect the male terminal of this wire to the system remote control
terminal of the car stereo (SYSTEM REMOTE CONTROL). The
female terminal can be connected to the auto-antenna relay control
terminal. If the car stereo does not have a system remote control ter-
minal, connect the male terminal to the power terminal through the
ignition switch.
Fuse (30 A)
Front side
Back side
To prevent damage
•Do not ground the speaker wire directly or con-
nect a negative (–) lead wire for several speakers.
•This unit is for vehicles with a 12-volt battery and
negative grounding. Before installing it in a recre-
ational vehicle, truck or bus, check the battery
voltage.
•If the car stereo is kept on for a long time while
the engine is at rest or idling, the battery may go
dead. Turn the car stereo off when the engine is at
rest or idling.
•If the system remote control wire of the amplifier
is connected to the power terminal through the
ignition switch (12 V DC), the amplifier will
always be on when the ignition is on— regardless
of whether the car stereo is on or off. Because of
this, the battery could go dead if the engine is at
rest or idling.
•Speakers to be connected to the amplifier should
conform with the standards listed below. If they
do not conform, they may catch fire, emit smoke
or become damaged. The speaker impedance must
be 2 to 8 ohms for stereo connection, and 4 to 8
ohms for monaural and other bridge connection.
•Install and route the separately sold battery wire
as far away as possible from the speaker wires.
Install and route the separately sold battery wire,
ground wire, speaker wires and the amplifier as
far away as possible from the antenna, antenna
cable and tuner.
•Cords for this product and those for other prod-
ucts may be different colors even if they have the
same function. When connecting this product to
another product, refer to the supplied Installation
manuals of both products and connect cords that
have the same function.
Speaker input terminal
See the “Using the
Speaker Input” section.
GM-X572
Speaker Channel Speaker Type Power
Two-channel Subwoofer Nominal input: Min. 80 W
Other than subwoofer Max. input: Min. 150 W
One-channel Subwoofer Nominal input: Min. 200 W
Other than subwoofer Max. input: Min. 400 W
GM-X372
Speaker Channel Speaker Type Power
Two-channel Subwoofer Nominal input: Min. 65 W
Other than subwoofer Max. input: Min. 100 W
One-channel Subwoofer Nominal input: Min. 140 W
Other than subwoofer Max. input: Min. 240 W
Connecting the Unit
CAUTION
•Do not install in:
—Places where it could injure the driver or pas-
sengers if the vehicle stops suddenly.
—Places where it may interfere with the driver,
such as on the floor in front of the driver’s
seat.
•Make sure that wires are not caught in the sliding
mechanism of the seats, resulting in a short-cir-
cuit.
•Confirm that no parts are behind the panel when
drilling a hole for installation of the amplifier.
Protect all cables and important equipment such
as fuel lines, brake lines and electrical wiring
from damage.
•Install tapping screws in such a way that the screw
tip does not touch any wire. This is important to
prevent wires from being cut by vibration of the
car, which can result in fire.
•To prevent electric shock, do not install the ampli-
fier in places where it might come in contact with
liquids.
•To ensure proper installation, use the supplied
parts in the manner specified. If any parts other
than the supplied ones are used, they may damage
internal parts of the amplifier, or they may
become loose causing the amplifier to shut down.
To prevent malfunction
•To ensure proper heat dissipation of the amplifier,
be sure of the following during installation.
—Allow adequate space above the amplifier for
proper ventilation.
—Do not cover the amplifier with a floor mat or
carpet.
•Do not install the amplifier near a door where it
may get wet.
•Do not install the amplifier on unstable places
such as the spare tire board.
•The best location for installation differs with the
car model and installation location. Secure the
amplifier at a sufficiently rigid location.
•Make temporary connections first and check that
the amplifier and the system operate properly.
•After installing the amplifier, confirm that the
spare tire, jack and tools can be easily removed.
Example of installation on the floor
mat or on the chassis
1. Place the amplifier where it is to be
installed. Insert the supplied tapping
screws (4 ×18 mm) into the screw
holes. Push on the screws with a
screwdriver so they make marks
where the installation holes are to be
located.
2. Drill 2.5 mm diameter holes at the
point marked, and install the ampli-
fier, either on the carpet or directly
to the chassis.
Installation
Drill a 2.5 mm diameter hole
Tapping-screws
(4 ×18 mm)
Floor mat
or chassis
Connecting the Speaker wires
The speaker output mode can be two-channel (stereo) or one-channel
(mono). Connect the speaker leads to suit the mode according to the figures
shown below.
•Do not connect both the RCA input and the speaker input at the same time.
Two-channel mode (stereo)
One-channel mode (mono)
(Right)
Speaker
(Left)
Speaker (Mono)
3. Connect the speaker wires to the
speaker output terminals.
•Connect the speaker wires, passing them
through the terminal cover.
•Fix the speaker wires securely with the termi-
nal screws.
4. Push on the terminal cover.
Using the Speaker Input
Connect the car stereo speaker output
wires to the amplifier using the supplied
speaker input connector.
•Do not connect both the RCA input and the
speaker input at the same time.
7Connections when using the speaker
input
Speaker
output
terminal
Terminal cover
Terminal screw
Speaker wire
Speaker output
Car Stereo
Speaker input connector
To speaker input terminal of
this unit.
White:
Left +
Gray:
Right +
White/black:
Left ≠
Gray/black:
Right ≠
Connecting the Power Terminal
•Always use the special red battery and ground
wire [RD-223], which is sold separately. Connect
the battery wire directly to the car battery positive
terminal (+) and the ground wire to the car body.
1. Pass the battery wire from the
engine compartment to the interior
of the vehicle.
•After making all other connections to the
amplifier, connect the battery wire terminal of
the amplifier to the positive (+) terminal of
the battery.
2. Twist the battery wire, ground wire
and system remote control wire.
3. Attach lugs to wire ends. Lugs not
supplied.
•Use pliers, etc., to crimp lugs to wires.
4. Connect the wires to the terminal.
•Fix the wires securely with the terminal
screws.
Connecting the Speaker Output
Terminals
1. Expose the end of the speaker wires
using nippers or a cutter by about
10 mm and twist.
2. Attach lugs to speaker wire ends.
Lugs not supplied.
•Use pliers, etc., to crimp lugs to wires.
10 mm
Fuse (30 A)
Engine
compart-
ment
Interior of
the vehicle
Drill a 14 mm
hole into the
vehicle body.
Insert the O-ring rubber
grommet into the vehicle
body.
Twist
Positive terminal
Fuse (30 A)
Battery wire
Ground wire
Lug
Lug
Twist
Speaker wire
Lug
GND terminal
Power terminal
Battery wire
System remote
control terminal
System remote
control wire
Ground wire

Product specificaties

Merk: Pioneer
Categorie: Receiver
Model: GM-X572

Heb je hulp nodig?

Als je hulp nodig hebt met Pioneer GM-X572 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Receiver Pioneer

Pioneer

Pioneer VSX-535 Handleiding

3 Mei 2024
Pioneer

Pioneer A-10EB Handleiding

12 Juli 2023
Pioneer

Pioneer VSX-531D-B Handleiding

4 Juli 2023
Pioneer

Pioneer DMH-342EX Handleiding

3 Juli 2023
Pioneer

Pioneer AVH-A215BT Handleiding

11 Juni 2023
Pioneer

Pioneer AVH-P6850DVD Handleiding

10 Juni 2023
Pioneer

Pioneer DMH-1770NEX Handleiding

6 Juni 2023
Pioneer

Pioneer VSXLX104 Handleiding

5 Juni 2023
Pioneer

Pioneer DEH-P2650 Handleiding

3 Juni 2023
Pioneer

Pioneer DMH-A5450BT Handleiding

21 Mei 2023

Handleiding Receiver

Nieuwste handleidingen voor Receiver

Henry Engineering

Henry Engineering AES DIGITAL DA 2X4 Handleiding

21 November 2024
Deaf Bonce

Deaf Bonce Machete MLA-70.2XS Handleiding

20 November 2024
QSC

QSC PowerLight 9.0 Handleiding

20 November 2024
Ashly

Ashly FX-125.4 Handleiding

20 November 2024
JBL

JBL Power P80.2 Handleiding

20 November 2024
JBL

JBL Power Px600.2 Handleiding

20 November 2024
JBL

JBL Power P-4020 Handleiding

20 November 2024
JBL

JBL Power P180.2 Handleiding

20 November 2024
JBL

JBL Power BPx1100.1 Handleiding

20 November 2024
JBL

JBL Power BPx500.1 Handleiding

20 November 2024