Pioneer GM-DX971 Handleiding

Pioneer Receiver GM-DX971

Lees hieronder de 📖 handleiding in het Nederlandse voor Pioneer GM-DX971 (8 pagina's) in de categorie Receiver. Deze handleiding was nuttig voor 44 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/8
PIONEER CORPORATION
28-8, Honkomagome 2-chome, Bunkyo-ku,
Tokyo 113-0021, JAPAN
PIONEER ELECTRONICS (USA) INC.
P.O. Box 1540, Long Beach, California 90801-1540, U.S.A.
TEL: (800) 421-1404
PIONEER EUROPE NV
Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium/Belgique
TEL: (0) 3/570.05.11
PIONEER ELECTRONICS ASIACENTRE PTE. LTD.
2 Jalan Kilang Barat, #07-01, Singapore 159346
TEL: 65-6378-7888
PIONEER ELECTRONICS AUSTRALIA PTY. LTD.
5 Arco Lane, Heatherton, Victoria, 3202 Australia
TEL: (03) 9586-6300
PIONEER ELECTRONICS DE MÉXICO S.A. DE C.V.
Blvd.Manuel Ávila Camacho 138, 10 piso
Col.Lomas de Chapultepec, México, D.F. 11000
TEL: 52-55-9178-4270
FAX: 52-55-5202-3714
先 公
台北 區407 8
886-(0)2-2657-3588
先 公電 限( )
909 5
852-2848-6488
En
Before you start
En
Before you start
English
Français
CLASS D MONO AMPLIFIER
AMPLIFICATEUR MONO DE CLASSE D
GM-D8701
GM-DX871
GM-D9701
GM-DX971
Owners Manual
Mode d’emploi
Thank you
WARNING CAUTION
Information to User
Note
After-sales service for
Pioneer products
USA & CANADA
If you experience problems
Visit our website
http://www.pioneerelectronics.com
http://www.pioneerelectronics.ca
The Safety of Your Ears is in
Your Hands
ESTABLISH A SAFE LEVEL:
BE SURE TO OBSERVE THE FOLLOWING
GUIDELINES:
About This Product
Before connecting/
installing the amplier
Wash hands after
handling.
<KNGZ20J> <5707000012762V> UC
© 2018-2020 PIONEER CORPORATION.
All rights reserved.
© 2018-2020 PIONEER CORPORATION.
Tous droits de reproduction et de traduction
réservés.
En
Before you start
Whats what
GM-D8701 and GM-DX871
Front side
21 3 4
Rear side
GM-D9701 and GM-DX971
Front side
21 3 4
Rear side
To adjust the switch, use a flathead screwdri-
ver if needed.
1POWER/PROTECT indicator
The power indicator lights up to indicate
power ON.
!If something is not normal, the indicator
turns red.
2GAIN (gain) control
If the output remains low, even when the car
stereo volume is turned up, turn the con-
trols to a lower level. If distortion occurs
when the car stereo volume is turned up,
turn these controls to a higher level.
!For use with an RCA equipped car stereo
(standard output of 500 mV), set to the
NORMAL position. For use with an RCA
equipped Pioneer car stereo, with maxi-
mum output of 4 V or more, adjust level
to match that of the car stereo output.
!For use with an RCA equipped car stereo
with output of 4 V, set to the position.H
!If you hear too much noise when using
the speaker input terminals, turn the
gain control to higher level.
3LPF (low-pass filter) cut off frequency
control
You can select a cut off frequency from
40 Hz to 240 Hz.
4BASS BOOST REMOTE (bass boost level
remote control) jack
By connecting the Bass boost level remote
control to the jack on the main unit, you will
be able to select a bass boost level from
0 dB to 18 dB.
For instruction of connecting the bass boost
remote control to the amplifier, see the Con-
nection diagram.
Setting gain properly
!Protective function included to prevent
malfunction of the unit and/or speakers
due to excessive output, improper use or
improper connection.
!When outputting high volume sound etc.,
this function cuts off the output for a few
seconds as a normal function, but output
is restored when the volume of the head
unit is turned down.
En
Setting the unit
!A cut in sound output may indicate impro-
per setting of the gain control. To ensure
continuous sound output with the head
unit at a high volume, set amplifier gain
control to a level appropriate for the preout
maximum output level of the head unit, so
that volume can remain unchanged and to
control excess output.
!Despite correct volume and gain settings,
the unit sound still cuts out periodically. In
such cases, please contact the nearest
authorized Pioneer Service Station.
Gain control of this unit
Preout level: 2 V (Standard: 500 mV)
Preout level: 4 V
Above illustration shows gain set-NORMAL
ting.
Relationship between amplifier gain
and head unit output power
If amplifier gain is raised improperly, this will
simply increase distortion, with little increase
in power.
Signal waveform when outputting at
high volume using amplifier gain
control
If the signal waveform is distorted due to high
output, even if the amplifier gain is raised, the
output power will change only slightly.
En
Setting the unit
Connection diagram
1Battery wire (sold separately)
!The maximum length of the wire be-
tween the fuse and the positive term-+
inal of the battery is 30 cm (12 in.).
!For the wire size, refer to Connecting the
power terminal. The battery wire, the
ground wire and the optional direct
ground wire must be same size. After
making all other connections at the am-
plifier, connect the battery wire terminal
of the amplifier to the positive term-+
inal of the battery.
2Fuse 100 A (GM-D8701 and GM-DX871) / 150 A
(GM-D9701 and GM-DX971) (sold separately)
Each amplifier must be separately fused at
100 A (GM-D8701 and GM-DX871) / 150 A (GM-
D9701 and GM-DX971).
3Positive terminal+
4Negative ( ) terminal*
5Battery (sold separately)
6Ground wire, Terminal (sold separately)
The ground wires must be same size as the
battery wire.
Connect to metal body or chassis.
7Car stereo with RCA output jacks (sold sepa-
rately)
8External output
9Connecting wire with RCA pin plugs (sold se-
parately)
aAmplifier with RCA input jacks (sold sepa-
rately)
bBass boost level remote control
cBass boost level remote control wire (5 m
(16 ft. 5 in.))
dRCA input jack
eRCA output jack
fSystem remote control wire (sold separately)
Connect male terminal of this wire to the sys-
tem remote control terminal of the car stereo.
The female terminal can be connected to the
auto-antenna relay control terminal. If the car
stereo lacks a system remote control terminal,
connect the male terminal to the power term-
inal via the ignition switch.
gSpeaker output terminals
Please see the following section for speaker
connection instructions. Refer to Connections
when using the speaker input wire.
hFuse 40 A × 2 (GM-D8701 and GM-DX871) /
40 A × 3 (GM-D9701 and GM-DX971)
iFront side
jRear side
Before connecting the
amplifier
WARNING
!Secure the wiring with cable clamps or adhe-
sive tape. To protect the wiring, wrap sections
in contact with metal parts in adhesive tape.
!Never cut the insulation of the power supply
to feed power to other equipment. Current ca-
pacity of the wire is limited.
CAUTION
!Never shorten any wires, the protection circuit
may malfunction.
En
Connecting the units
*
CAUTION
!Always keep the volume low enough to hear
outside sounds.
!Extended use of the car stereo while the en-
gine is at rest or idling may exhaust the bat-
tery.
!This product is evaluated in moderate and tro-
pical climate condition under the Audio, video
and similar electronic apparatus - Safety re-
quirements, IEC 60065.
!The graphical symbol placed on the
product means direct current.
!Connect either of three subwoofers to the am-
plifier; 1: a subwoofer with a 300 W (GM-D8701
and GM-DX871) / 500 W (GM-D9701 and GM-
DX971) or larger nominal input and an impe-
dance 4 W, 2: a subwoofer with a 500 W (GM-
D8701 and GM-DX871) / 800 W (GM-D9701
and GM-DX971) or larger nominal input and
an impedance 2 or 3: a subwoofer with aW
800 W (GM-D8701 and GM-DX871) / 1 200 W
(GM-D9701 and GM-DX971) or larger nominal
input and an impedance 1 W.
About the protection function
This product has protection function. When this
product detects something abnormal, the follow-
ing functions will operate to protect the product
and speaker output.
!The indicator will turn redPOWER/PROTECT
and the amplifier will shut down in the situa-
tions outlined below.
If the temperature inside the amplifier gets
too high.
If a DC voltage is applied to the speaker
output terminal.
!The indicator will turn redPOWER/PROTECT
and the output will be muted in the situations
outlined below.
If the speaker output terminal and speaker
wire are short-circuited.
Important (Serial number)
The serial number is located on the bottom of
this unit. For your own security and convenience,
be sure to record this number on the enclosed
warranty card.
If the nominal input and impedance are out of
the above ranges, the subwoofer may catch
fire, emit smoke or become damaged.
!Never wire the speaker negative cable directly
to ground.
!Never band together multiple speaker s nega-
tive cables.
!If the system remote control wire of the ampli-
fier is connected to the power terminal via the
ignition switch (12 V DC), the amplifier will re-
main on with the ignition whether the car
stereo is on or off, which may exhaust battery
if the engine is at rest or idling.
!Install and route the separately sold battery
wire as far as possible from the speaker wires.
Install and route the separately sold battery
wire, ground wire, speaker wires and the am-
plifier as far away as possible from the anten-
na, antenna cable and tuner.
Connecting the speakers
This amplifier can be connected to two speak-
ers in parallel. Connect the speaker leads to
suit the mode according to the figure shown
below.
Precautions for parallel connection
!When wiring two speakers in parallel, make
sure that the synthetic impedance is from
1 to 8 to prevent the amplifier fromW W
catching fire, generating smoke and/or
being damaged.
!When connected in parallel with the syn-
thetic impedance less than 1 W, as a nor-
mal function, this amplifier may
automatically be set on mute if outputting
high volume sound. Turn down the volume
until the mute function is canceled.
When connecting to one speaker
Speaker output
When connecting to two speakers
The output from two speakers is the same as
that of one speaker.
En
Connecting the units
Connections when using
the speaker input wire
Connect the car stereo speaker output wires
to the amplifier using the supplied speaker
input wire with RCA pin cord.
1Car Stereo
2Speaker output
3Red: Right +
4Black: Right *
5Black: Left *
6White: Left +
7Speaker input wire with RCA pin cord
To the RCA input jack of this unit
Notes
!If speaker input wires from a headunit are
connected to this amplifier, the amplifier will
automatically turn on when the headunit is
turned on. When the headunit is turned off,
the amplifier turns off automatically. This
function may not work with some headunits.
In such cases, please use a system remote
control wire (sold separately). If multiple am-
plifiers are to be connected together synchro-
nously, connect the head unit and all
amplifiers via the system remote control wire.
!Connect the system remote control wire when
you wish to only turn on the car stereo, not the
amplifier.
!This amplifier automatically selects an input
signal mode between the RCA level and the
speaker level by detecting an input signal.
Solderless terminal
connections
!Since the wire will become loose over time,
it must be periodically inspected and tigh-
tened as necessary.
!Do not solder or bind the ends of the
twisted wires.
!Fasten while making sure to not to clamp
the insulating sheath of the wire.
!Use the supplied hexagonal wrench to
tighten and loosen the terminal screw of
the amplifier and use it to securely fasten
the wire. Be careful to avoid excessive tigh-
tening of this screw, which may damage
the wire.
Connecting the power terminal
WARNING
If the battery wire is not securely fixed to the term-
inal using the terminal screws, there is a risk of
overheating, malfunction and injury, including
minor burns.
!Always use the recommended battery and
ground wire, which is sold separately. Con-
nect the battery wire directly to the car bat-
tery positive ( ) terminal and the ground+
wire to the car body.
!Recommended wires size (AWG: American
Wire Gauge) is as follows. The battery wire,
the ground wire and the optional direct
ground wire must be same size.
!Use a wire of 8 AWG to 16 AWG wire for the
speaker wire.
Battery wire and ground wire size
Wire length Wire size
less than 3.6 m (11 ft. 10 in.) 6 AWG
less than 6.4 m (20 ft. 12 in.) 4 AWG
En
Connecting the units
1 Route battery wire from engine com-
partment to the vehicle interior.
!When drilling a cable pass-hole into the ve-
hicle body and routing a battery wire thor-
ough it, take care not to short-circuit the
wire damaging it by the cut edges or burrs
of the hole.
After completing all other amplifier connec-
tions, finally connect the battery wire terminal
of the amplifier to the positive battery term-+
inal.
2
1 3
1Positive terminal+
2Battery wire (sold separately)
The maximum length of the wire between
the fuse and the positive terminal of the+
battery is 30 cm (12 in.).
3Fuse 100 A (GM-D8701 and GM-DX871) /
150 A (GM-D9701 and GM-DX971) (sold se-
parately)
Each amplifier must be separately fused at
100 A (GM-D8701 and GM-DX871) / 150 A
(GM-D9701 and GM-DX971).
2 Use wire cutters or a utility knife to
strip the end of the battery wire, ground
wire and system remote control wire to ex-
pose about 10 mm (3/8 in.) of the end of
each of the wires, and then twist the ex-
posed ends of the wires.
Twist
10 mm (3/8 in.)
3 Connect the wires to the terminal.
Fix the wires securely with the terminal
screws.
3
6
1
5
4
2
7
1Battery wire
2Power terminal
3Ground wire
4GND terminal
5System remote control wire
6System remote control terminal
7Terminal screws
En
Connecting the units
Connecting the speaker output
terminals
1 Use wire cutters or a utility knife to
strip the end of the speaker wires to ex-
pose about 10 mm (3/8 in.) of wire and
then twist the wire.
Twist
10 mm (3/8 in.)
2 Connect the speaker wires to the
speaker output terminals.
Fix the wires securely with the terminal
screws.
1
3
2
1Terminal screws
2Speaker wires
3Speaker output terminals
Before installing the amplifier
WARNING
!To ensure proper installation, use the supplied
parts in the manner specified. If any parts
other than those supplied are used, they may
damage internal parts of the amplifier, or be-
come loose causing the amplifier to shut
down.
!Do not install in:
Places where it could injure the driver or
passengers if the vehicle stops suddenly.
Places where it may interfere with the dri-
ver, such as on the floor in front of the dri-
ver s seat.
!Install tapping screws in such a way that the
screw tip does not touch any wire. This is im-
portant to prevent wires from being cut by vi-
bration of the car, which can result in fire.
!Make sure that wires do not get caught in the
sliding mechanism of the seats or touch the
legs of a person in the vehicle as short-circuit
may result.
!When drilling to install the amplifier, always
confirm no parts are behind the panel and
protect all cables and important equipment
(e.g. fuel/brake lines, wiring) from damage.
CAUTION
!To ensure proper heat dissipation of the ampli-
fier, ensure the following during installation:
Allow adequate space above the amplifier
for proper ventilation.
Do not cover the amplifier with a floor mat
or carpet.
!Place all cables away from hot places, such
as near the heater outlet.
!The optimal installation location differs de-
pending on the car model. Secure the ampli-
fier at a sufficiently rigid location.
!Check all connections and systems before
final installation.
!After installing the amplifier, confirm that the
spare tire, jack and tools can be easily re-
moved.
En
Connecting the units Installation


Product specificaties

Merk: Pioneer
Categorie: Receiver
Model: GM-DX971

Heb je hulp nodig?

Als je hulp nodig hebt met Pioneer GM-DX971 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Receiver Pioneer

Handleiding Receiver

Nieuwste handleidingen voor Receiver