Pioneer GM-D500M Handleiding

Pioneer Receiver GM-D500M

Lees hieronder de 📖 handleiding in het Nederlandse voor Pioneer GM-D500M (6 pagina's) in de categorie Receiver. Deze handleiding was nuttig voor 22 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/6

Setting the Unit

Bass Level Control

If the sound level is too low, even when

the volume of the car stereo used along

with this power amplifier is turned up,

turn bass level control on the front of the

power amplifier clockwise. If the sound

distorts when the volume is turned up,

turn the bass level control counter-clock-

wise.

• When using with an RCA equipped car

stereo (standard output of 500 mV), set to

the NORMAL position. When using with

an RCA equipped Pioneer car stereo with

max. output of 4 V or more, adjust level to

match the car stereo output level.

• When you want to boost bass, turn the bass

level control clockwise.

Power Indicator

The power indicator lights when the

power is switched on.

BFC (Beat Frequency Control) Switch

If you hear a beat while listening to an

AM broadcast with your car stereo,

change the BFC switch using a small

standard tip screwdriver.

Thank you for purchasing this PIONEER

product. Before attempting operation, be

sure to read this manual.

In case of trouble

When the unit does not operate properly,

contact your dealer or the nearest autho-

rized PIONEER Service Station.

About This Product

This product is a class D amplifier for the

subwoofer. If both L (left) and R (right)

channels are connected to the RCA input

of this product, output is mixed because

this product is a mono amplifier.

WARNING

• Always use the special red battery and ground

wire [RD-223], which is sold separately. Connect

the battery wire directly to the car battery positive

terminal (+) and the ground wire to the car body.

• Do not touch the amplifier with wet hands.

Otherwise you may get an electric shock. Also, do

not touch the amplifier when it is wet.

• For traffic safety and to maintain safe driving

conditions, keep the volume low enough so that

you can still hear normal traffic sound.

• Check the connections of the power supply and

subwoofer if the fuse of the separately sold bat-

tery wire or the amplifier fuse blows. Detect the

cause and solve the problem, then replace the fuse

with another one of the same size and rating.

• To prevent malfunction of the amplifier and sub-

woofer, the protective circuit will cut the power

supply to the amplifier (sound will stop) when an

abnormal condition occurs. In such a case, switch

the power to the system OFF and check the

connection of the power supply and subwoofer.

Detect the cause and solve the problem.

• Contact the dealer if you cannot detect the cause.

• To prevent an electric shock or short-circuit

during connection and installation, be sure to

disconnect the negative (–) terminal of the battery

beforehand.

• Confirm that no parts are behind the panel when

drilling a hole for installation of the amplifier. Be

sure to protect all cables and important equipment

such as fuel lines, brake lines and the electrical

wiring from damage.

Before Using This Product

PIONEER CORPORATION

4-1, MEGURO 1-CHOME, MEGURO-KU, TOKYO 153-8654, JAPAN

PIONEER ELECTRONICS (USA) INC.

P.O. Box 1540, Long Beach, California 90801-1540, U.S.A.

TEL: (800) 421-1404

PIONEER EUROPE NV

Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium

TEL: (0) 3/570.05.11

PIONEER ELECTRONICS ASIACENTRE PTE. LTD.

253 Alexandra Road, #04-01, Singapore 159936

TEL: 65-6472-1111

PIONEER ELECTRONICS AUSTRALIA PTY. LTD.

178-184 Boundary Road, Braeside, Victoria 3195, Australia

TEL: (03) 9586-6300

PIONEER ELECTRONICS OF CANADA, INC.

300 Allstate Parkway, Markham, Ontario L3R OP2, Canada

TEL: (905) 479-4411

PIONEER ELECTRONICS DE MEXICO, S.A. de C.V.

San Lorenzo 1009 3er. Piso Desp. 302

Col. Del Valle Mexico, D.F. C.P. 03100

TEL: 55-5688-52-90

Published by Pioneer Corporation.

Publicado por Pioneer Corporation.

Printed in U.S.A.

Impreso en los EE.UU.

<HRD0207-A> ES<KYMFX/02I00000>

CLASS D MONO AMPLIFIER

AMPLIFICADOR MONO DE CLASE D

Owner’s Manual

GM-D500M

Manual del Propietario

Cut Off Frequency Control

You can select a cut off frequency from

40 to 240 Hz.

Connecting the Power Terminal

• Always use the special red battery and ground

wire [RD-223], which is sold separately. Connect

the battery wire directly to the car battery positive

terminal (+) and the ground wire to the car body.

1. Pass the battery wire from the

engine compartment to the interior

of the vehicle.

• After making all other connections to the

amplifier, connect the battery wire terminal of

the amplifier to the positive (+) terminal of

the battery.

2. Twist the battery wire, ground wire

and system remote control wire.

3. Attach lugs to wire ends. Lugs not

supplied.

• Use pliers, etc., to crimp lugs to wires.

4. Connect the wires to the terminal.

• Fix the wires securely with the terminal

screws.

Fuse (30 A)

Engine

compart-

ment

Interior of

the vehicle

Drill a 14 mm

hole into the

vehicle body.

Insert the O-ring rubber

grommet into the vehicle

body.

Twist

Positive terminal

GND terminal

Power terminal

Battery wire

System remote

control terminal

System remote

control wire

Ground wire

Fuse (30 A)

Battery wire

Ground wire

Lug

Connecting the Unit

CAUTION

• Disconnect the negative (–) terminal of the battery

to avoid the risk of short-circuit and damage to

the unit.

• Secure the wiring with cable clamps or adhesive

tape. To protect the wiring, wrap adhesive tape

around it where they lie against metal parts.

• Do not route wires where they will get hot, for

example where the heater will blow over them. If

the insulation heats up, it may become damaged,

resulting in a short-circuit through the vehicle

body.

• Make sure that wires will not interfere with mov-

ing parts of the vehicle, such as the gearshift,

handbrake or seat sliding mechanism.

• Do not shorten any wires. Otherwise the protec-

tion circuit may fail to work when it should.

• Never feed power to other equipment by cutting

the insulation of the power supply wire to tap

from the wire. The current capacity of the wire

will be exceeded, causing overheating.

Connection Diagram Connecting the Speaker Terminals

1. Expose the end of the speaker wires

using nippers or a cutter by about

10 mm and twist.

2. Attach lugs to speaker wire ends.

Lugs not supplied.

• Use pliers, etc., to crimp lugs to wires.

3. Connect the speaker wires to the

speaker terminals.

• Fix the speaker wires securely with the termi-

nal screws.

10 mm

Twist

Speaker

terminal

Terminal screw

Speaker wire

Lug

Speaker wire

Fuse (30 A)

Grommet

Special red battery wire [RD-223] (sold separately)

After making all other connections at the amplifier,

connect the battery wire terminal of the amplifier to

the positive (+) terminal of the battery.

Ground wire (black) [RD-223] (sold separately)

Connect to metal body or chassis.

Fuse (30 A) ×2

Car stereo with

RCA output jacks

External Output

(Subwoofer output)

Connecting wires with RCA

pin plugs (sold separately).

RCA input jack

Speaker terminal

See the “Connecting the Speaker

wires” section for speaker connec-

tion instructions.

System remote control wire (sold separately)

Connect the male terminal of this wire to the system remote control

terminal of the car stereo (SYSTEM REMOTE CONTROL). The

female terminal can be connected to the auto-antenna relay control

terminal. If the car stereo does not have a system remote control ter-

minal, connect the male terminal to the power terminal through the

ignition switch.

Fuse (30 A)

To prevent damage

• Do not ground the speaker wire directly or con-

nect a negative (–) lead wire for several speakers.

• This unit is for vehicles with a 12-volt battery and

negative grounding. Before installing it in a recre-

ational vehicle, truck or bus, check the battery

voltage.

• If the car stereo is kept on for a long time while

the engine is at rest or idling, the battery may go

dead. Turn the car stereo off when the engine is at

rest or idling.

• If the system remote control wire of the amplifier

is connected to the power terminal through the

ignition switch (12 V DC), the amplifier will

always be on when the ignition is on— regardless

of whether the car stereo is on or off. Because of

this, the battery could go dead if the engine is at

rest or idling.

• Connect a subwoofer with a 380 W or larger nom-

inal input and an impedance between 1 and 8

ohms to the amplifier. If the nominal input and

impedance are out of the above ranges, the sub-

woofer may catch fire, emit smoke or become

damaged.

• Install and route the separately sold battery wire

as far away as possible from the speaker wires.

Install and route the separately sold battery wire,

ground wire, speaker wires and the amplifier as

far away as possible from the antenna, antenna

cable and tuner.

• Cords for this product and those for other prod-

ucts may be different colors even if they have the

same function. When connecting this product to

another product, refer to the supplied Installation

manuals of both products and connect cords that

have the same function.

Connecting the Unit

CAUTION

• Do not install in:

—Places where it could injure the driver or pas-

sengers if the vehicle stops suddenly.

—Places where it may interfere with the driver,

such as on the floor in front of the driver’s

seat.

• Make sure that wires are not caught in the sliding

mechanism of the seats, resulting in a short-cir-

cuit.

• Confirm that no parts are behind the panel when

drilling a hole for installation of the amplifier.

Protect all cables and important equipment such

as fuel lines, brake lines and electrical wiring

from damage.

• Install tapping screws in such a way that the

screw tip does not touch any wire. This is impor-

tant to prevent wires from being cut by vibration

of the car, which can result in fire.

• To prevent electric shock, do not install the ampli-

fier in places where it might come in contact with

liquids.

• To ensure proper installation, use the supplied

parts in the manner specified. If any parts other

than the supplied ones are used, they may damage

internal parts of the amplifier, or they may

become loose causing the amplifier to shut down.

To prevent malfunction

• To ensure proper heat dissipation of the amplifier,

be sure of the following during installation.

—Allow adequate space above the amplifier for

proper ventilation.

—Do not cover the amplifier with a floor mat or

carpet.

• Do not install the amplifier near a door where it

may get wet.

• Do not install the amplifier on unstable places

such as the spare tire board.

• The best location for installation differs with the

car model and installation location. Secure the

amplifier at a sufficiently rigid location.

• Make temporary connections first and check that

the amplifier and the system operate properly.

• After installing the amplifier, confirm that the

spare tire, jack and tools can be easily removed.

Example of installation on the floor

mat or on the chassis

1. Place the amplifier where it is to be

installed. Insert the supplied tapping

screws (4 18 mm) into the screw×

holes. Push on the screws with a

screwdriver so they make marks

where the installation holes are to be

located.

2. Drill 2.5 mm diameter holes at the

point marked, and install the ampli-

fier, either on the carpet or directly

to the chassis.

Installation

Drill a 2.5 mm diameter hole

Tapping-screws

(4 ×18 mm)

Floor mat

or chassis

Specifications

Power source .............................................................................................................. 14.4 V DC (10.8 — 15.1 V allowable)

Grounding system ............................................................................................................................................ Negative type

Current consumption ........................................................................................................ 31.0 A (at continuous power, 4 Ω)

Average current drawn* ............................................................................................................ 4.4 A (4 Ωfor one channel)

7.3 A (2 Ωfor one channel)

Fuse ............................................................................................................................................................................ 30 A × 2

Dimensions ........................................................................................................................ 268 (W) 52 (H) × × 250 (D) mm

Weight ...................................................................................................................... 2.9 kg (Leads for wiring not included)

Maximum power output ............................................................................................ 600 W × 1 (4 Ω) / 1,000 W × 1 (2 Ω)

Continuous power output ................................................................ 300 W 1 (at 14.4 V, 4 , 20 — 240 Hz, 0.4% THD)× Ω

500 W × 1 (at 14.4 V, 2 , 20 — 240 Hz, 0.8% THD)Ω

Load impedance ............................................................................................................................ 4 Ω(1 — 8 Ωallowable)

Frequency response ................................................................................................................ 5 — 240 Hz (+0.5 dB, –3 dB)

Distortion ............................................................................................................................................ 0.03% (10 W, 120 Hz)

Low pass filter .................................................................................................................... Cut off frequency: 40 — 240 Hz

Cut off slope: –24 dB/oct

Bass level control ............................................................................................................................................ –22 — +12 dB