Pioneer DVH-3100UB Handleiding

Pioneer Niet gecategoriseerd DVH-3100UB

Lees hieronder de 📖 handleiding in het Nederlandse voor Pioneer DVH-3100UB (6 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 11 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/6
Connecting the Units <ENGLISH>
WARNING
• To avoid the risk of accident and the potential
violation of applicable laws, the front DVD or TV
(sold separately) feature should never be used
while the vehicle is being driven. Also, Rear
Displays should not be in a location where it is a
visible distraction to the driver.
• In some countries or states the viewing of images
on a display inside a vehicle even by persons other
than the driver may be illegal. Where such
regulations apply, they must be obeyed and this
unit’s DVD features should not be used.
CAUTION
• PIONEER does not recommend that you install or
service your display yourself. Installing or
servicing the product may expose you to risk of
electric shock or other hazards. Refer all
installation and servicing of your display to
authorized Pioneer service personnel.
• Secure all wiring with cable clamps or adhesive
tape. Do not allow any bare wiring to remain
exposed.
• Do not drill a hole into the engine compartment to
connect the yellow lead of the unit to the vehicle
battery. Engine vibration may eventually cause the
insulation to fail at the point where the wire passes
from the passenger compartment into the engine
compartment. Take extra care in securing the wire
at this point.
• It is extremely dangerous to allow the display lead
to become wound around the steering column or
gearshift. Be sure to install the display in such a
way that it will not obstruct driving.
• Make sure that wires will not interfere with
moving parts of the vehicle, such as the gearshift,
parking brake or seat sliding mechanism.
• Do not shorten any leads. If you do, the protection
circuit may fail to work properly.
Note:
•This unit cannot be installed in a vehicle that
does not have an ACC (accessory) position on
the ignition switch.
• Use this unit in other than the following
conditions could result in fire or malfunction.
— Vehicles with a 12-volt battery and negative
grounding.
— Speakers with 50 W (output value) and 4 ohm
to 8 ohm (impedance value).
• To prevent short-circuit, overheating or
malfunction, be sure to follow the directions
below.
— Disconnect the negative terminal of the battery
before installation.
— Secure the wiring with cable clamps or adhe-
sive tape. To protect the wiring, wrap adhesive
tape around them where they lie against metal
parts.
— Place all cables away from moving parts, such
as gear shift and seat rails.
— Place all cables away from hot places, such as
near the heater outlet.
— Do not pass the yellow cable through a hole
into the engine compartment to connect to a
battery.
— Cover any disconnected cable connectors with
insulating tape.
— Do not shorten any cables.
— Never cut the insulation of the power cable of
this unit in order to share the power to other
equipment. Current capacity of the cable is
limited.
— Use a fuse of the rating prescribed.
— Never wire the speaker negative cable directly
to ground.
— Never band together multiple speaker’s nega-
tive cables.
• Control signal is output through blue/white cable
when this unit is powered on. Connect it to an
external power amp’s system remote control or
the vehicle’s auto-antenna relay control terminal
(max. 300 mA, 12 V DC). If the vehicle is
equipped with a glass antenna, connect it to the
antenna booster power supply terminal.
• Never connect blue/white cable to external power
amp’s power terminal. Also, never connect it to
the power terminal of the auto antenna.
Otherwise, battery drain or malfunction may
result.
• Black cable is ground. This cable and other
product’s ground cable (especially, high-current
products such as power amp) must be wired
separately. Otherwise, fire or malfunction may
result if they are accidentally detached.
No ACC positionACC position
O
N
S
T
A
R
T
O
F
F
A
C
C
O
N
S
T
A
R
T
O
F
F
Power cable connection
1*
2*
4*
3*
5*
Note:
Depending on the kind of vehicle, the
function of 3* and 5* may be different. In
this case, be sure to connect 2* to 5* and 4*
to 3*.
Connect leads of the same
color to each other.
Cap (1*)
Do not remove cap if
this terminal is not in
use.
Yellow (3*)
Back-up (or
accessory)
Red (5*)
Accessory
(or back-up)
Yellow (2*)
Connect to the constant
12 V supply terminal.
Red (4*)
Connect to terminal controlled
by ignition switch (12 V DC).
ISO connector
Note:
In some vehicles, the ISO connector
may be divided into two. In this case,
be sure to connect to both connectors.
Speaker leads
White: Front left +
White/black: Front left ≠
Gray: Front right +
Gray/black: Front right ≠
Green: Rear left +
Green/black: Rear left ≠
Violet: Rear right +
Violet/black: Rear right ≠
Blue/white
Connect to system control terminal of the
power amp (max. 300 mA 12 V DC).
Blue/white (7*)
Connect to auto-antenna relay control
terminal (max. 300 mA 12 V DC).
The pin position of the ISO connector will dier
depends on the type of vehicle. Connect 6* and
7* when Pin 5 is an antenna control type. In
another type of vehicle, never connect 6* and 7*.
Yellow/black
If you use an equipment with Mute function, wire
this lead to the Audio Mute lead on that equipment.
If not, keep the Audio Mute lead free of any
connections.
Black (chassis ground)
Connect to a clean, paint-free metal location.
This productAntenna jack
Fuse (10 A)
Fuse resistor
Wired remote input
Hard-wired remote control adaptor can be
connected (sold separately).
Blue/white (6*)
<KMIZX> <08I00000>
Printed in Thailand
<CRD4387-A/N> UW
Installation Manual
DVD RDS RECEIVER
DVD RDS êÖëàÇÖê
DVH-3100UB
ç‡Ô˜‡Ú‡ÌÓ ‚ í‡Ë·̉Â
Connecting the Units <ENGLISH>
Connecting to separately sold power amp
Connect with RCA cables
(sold separately)
Perform these connections when
using the optional amplier.
Power amp (sold
separately)
System remote control
Blue/white
Connect to system control terminal of the
power amp (max. 300 mA 12 V DC).
+
≠
+
≠
Blue/white (7*)
Connect to auto-antenna relay control
terminal (max. 300 mA 12 V DC).
The pin position of the ISO connector will
dier depends on the type of vehicle.
Connect 6* and 7* when Pin 5 is an
antenna control type. In another type of
vehicle, never connect 6* and 7*.
Blue/white (6*)
Rear speakerRear speaker
This product Rear output
When using a display connected video outputs
WARNING
Never install the display in a location where it is visible to the driver while driving.
Display with
RCA input jacks
To video input
RCA cable
(supplied)
1.5 m
This product
Video output
(VIDEO OUTPUT)
Installation <ENGLISH>
Note:
•Check all connections and systems before final
installation.
•Do not use unauthorized parts. The use of
unauthorized parts may cause malfunctions.
•Consult with your dealer if installation requires
drilling of holes or other modifications of the
vehicle.
•Do not install this unit where:
—it may interfere with operation of the vehicle.
—it may cause injury to a passenger as a result
of a sudden stop.
•The semiconductor laser will be damaged if it
overheats. Install this unit away from hot places
such as near the heater outlet.
•Optimum performance is obtained when the unit
is installed at an angle of less than 30°.
•When installing, to ensure proper heat dispersal
when using this unit, make sure you leave ample
space behind the rear panel and wrap any loose
cables so they are not blocking the vents.
DIN Rear-mount
1. Extend top and bottom of the trim ring outwards
to remove the trim ring. When reattaching the
trim ring, push the trim ring onto the unit until it
clicks. (If the trim ring is attached upside down,
the trim ring will not fit properly.)
•It becomes easy to remove the trim ring if the
front panel is released.
2. Determine the appropriate position where the
holes on the bracket and the side of the unit
match.
3. Tighten two screws on each side.
•Use either truss screws (5 mm ×8 mm) or
flush surface screws (5 mm ×9 mm), depend-
ing on the shape of screw holes in the
bracket.
Fastening the front panel
If you do not plan to detach the front panel, the
front panel can be fastened with supplied screw.
DIN Front/Rear-mount
This unit can be properly installed either from
“ ”Front (conventional DIN Front-mount) or
“ ”Rear (DIN Rear-mount installation, utilizing
threaded screw holes at the sides of unit chassis).
For details, refer to the following installation
methods.
DIN Front-mount
Installation with the rubber bush
1. Insert the mounting sleeve into the dashboard.
•When installing in a shallow space, use a sup-
plied mounting sleeve. If there is enough
space behind the unit, use factory supplied
mounting sleeve.
2. Secure the mounting sleeve by using a
screwdriver to bend the metal tabs (90 ) into°
place.
3. Install the unit as illustrated.
Removing the Unit
1. Extend top and bottom of the trim ring outwards
to remove the trim ring. When reattaching the
trim ring, push the trim ring onto the unit until it
clicks. (If the trim ring is attached upside down,
the trim ring will not fit properly.)
•It becomes easy to remove the trim ring if the
front panel is released.
2. Insert the supplied extraction keys into both sides
of the unit until they click into place.
3. Pull the unit out of the dashboard.
53
53
182182
Trim ring Trim ring
Screw
Dashboard or Console
Factory radio mounting bracket
Rubber bush
Screw
Dashboard Mounting sleeve
Screw

Product specificaties

Merk: Pioneer
Categorie: Niet gecategoriseerd
Model: DVH-3100UB

Heb je hulp nodig?

Als je hulp nodig hebt met Pioneer DVH-3100UB stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Pioneer

Pioneer

Pioneer BDR-212V Handleiding

30 September 2024
Pioneer

Pioneer CA-HM-SST.001 Handleiding

26 September 2024
Pioneer

Pioneer SDA-RP100 Handleiding

24 September 2024
Pioneer

Pioneer CA-R-FIA.002 Handleiding

24 September 2024
Pioneer

Pioneer CA-R-CG.003 Handleiding

24 September 2024
Pioneer

Pioneer CA-R-NI.005AE Handleiding

24 September 2024
Pioneer

Pioneer CA-HM-SUZ.007 Handleiding

24 September 2024
Pioneer

Pioneer CA-HM-HO.003 Handleiding

24 September 2024
Pioneer

Pioneer CA-R-PI.017 Handleiding

24 September 2024
Pioneer

Pioneer CD-HW-MIT.003 Handleiding

24 September 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Taga Harmony

Taga Harmony TOS-600 v.2 Handleiding

26 November 2024
Trace Elliot

Trace Elliot Pro 2x12 Cabinet Handleiding

26 November 2024
Kramer

Kramer K-Bar Camera Bracket Handleiding

26 November 2024
Kramer

Kramer RK-19 Handleiding

26 November 2024
Kramer

Kramer OSP-MM1 Handleiding

26 November 2024
Kramer

Kramer ASPEN-1616UX Handleiding

26 November 2024
Korg

Korg Pitchstrap Handleiding

26 November 2024
NeoMounts

NeoMounts WL70-450BL11 Handleiding

26 November 2024
Kramer

Kramer CLS-AOCH/60 Handleiding

26 November 2024
Klauke

Klauke EKM 6022ISM Handleiding

26 November 2024