Pioneer DMH-WT7600NEX Handleiding

Pioneer Receiver DMH-WT7600NEX

Lees hieronder de 📖 handleiding in het Nederlandse voor Pioneer DMH-WT7600NEX (52 pagina's) in de categorie Receiver. Deze handleiding was nuttig voor 36 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/52
English Français Español
DMH-WT8600NEX
DMH-WT7600NEX
DMH-WT86NEX
DMH-WT76NEX
DMH-WC6600NEX
DMH-WC5700NEX
DMH-W4660NEX
DMH-W4600NEX
RDS AV RECEIVER
RÉCEPTEUR AV AVEC RDS
RECEPTOR AV RDS
Installation Manual
Manuel d’installation
Manual de instalación
2En
WARNING
Rear visibility systems (backup cameras)
are required in certain new vehicles sold in
the U.S. and Canada. U.S. regulations
began according to a two year phase-in on
May 1, 2016, and both the U.S. and Canada
require that all such vehicles manufactured
on or after May 1, 2018 have rear visibility
systems. Owners of vehicles equipped
with compliant rear visibility systems
should not install or use this product in
a way that alters or disables that
system's compliance with applicable
regulations. If you are unsure whether
your vehicle has a rear visibility system
subject to the U.S. or Canadian regulations,
please contact the vehicle manufacturer or
dealer.
If your vehicle has a compliant backup
camera that displays the backup view
through the factory receiver, do not use
the Pioneer receiver unless it is connected
to and displays the same view as the
factory backup camera. Connection to the
factory backup camera will require an
adaptor, sold separately. Not all vehicles
may be able to connect. Please check with
a qualified professional installer for
installation options specific to your vehicle.
•Do not operate this product, any
applications, or the rear view camera
option (if purchased) if doing so will
divert your attention in any way from the
safe operation of your vehicle. Always
observe safe driving rules and follow all
existing traffic regulations. If you
experience difficulty in operating this
product, pull over, park your vehicle in a
safe location and apply the parking brake
before making the necessary
adjustments.
•Do not install this product where it may
(i) obstruct the driver’s vision,
(ii) impair the performance of any of the
vehicle’s operating systems of safety
features, including airbags, hazard lamp
buttons, or
(iii) impair the driver’s ability to safely
operate the vehicle.
In some cases, it may not be possible to
install this product because of the vehicle
type or the shape of the vehicle interior.
Important safety
information
Connection
Precautions
Your new product and this
manual
WARNING
Pioneer does not recommend that you
install this product yourself. This product is
designed for professional installation only.
We recommend that only authorized
Pioneer service personnel, who have
special training and experience in mobile
electronics, set up and install this product.
NEVER SERVICE THIS PRODUCT YOURSELF.
Installing or servicing this product and its
connecting cables may expose you to the
risk of electric shock or other hazards, and
can cause damage to this product that is
not covered by warranty.
CAUTION
•Secure all wiring with cable clamps or
electrical tape. Do not allow any bare
wiring to remain exposed.
•Do not directly connect the yellow lead of
this product to the vehicle battery. If the
lead is directly connected to the battery,
engine vibration may eventually cause
the insulation to fail at the point where
the wire passes from the passenger
compartment into the engine
compartment. If the yellow lead’s
insulation tears as a result of contact with
metal parts, short-circuiting can occur,
resulting in considerable danger.
•It is extremely dangerous to allow cables
to become wound around the steering
column or shift lever. Be sure to install
this product, its cables, and wiring away
in such so that they will not obstruct or
hinder driving.
•Make sure that the cables and wires will
not interfere with or become caught in
any of the vehicle’s moving parts,
especially the steering wheel, shift lever,
parking brake, sliding seat tracks, doors,
or any of the vehicle’s controls.
•Do not route wires where they will be
exposed to high temperatures. If the
insulation heats up, wires may become
damaged, resulting in a short circuit or
malfunction and permanent damage to
the product.
•Do not shorten any leads. If you do, the
protection circuit (fuse holder, fuse
resistor or filter, etc.) may fail to work
properly.
•Never feed power to other electronic
products by cutting the insulation of the
power supply lead of this product and
tapping into the lead. The current
capacity of the lead will be exceeded,
causing overheating.
•Use this unit with a 12-volt battery and
negative grounding only. Failure to do so
may result in a fire or malfunction.
•To avoid shorts in the electrical system,
be sure to disconnect the (–) battery
cable before installation.
WARNING
•When speaker output is used by 4
channels , use speakers over 50 W
(Maximum input power) and between 4
Ω to 8 Ω (impedance value). Do not use 1
Ω to 3 Ω speakers for this unit.
•When rear speaker output is used by 2 Ω
of subwoofer, use speakers over 70 W
(Maximum input power).
*Please refer to connection for a
connection method.
Important safeguards
Precautions before
connecting the system Before installing this
product
To prevent damage
3En
English
•The black lead is ground. When installing
this unit or power amp (sold separately),
make sure to connect the ground wire
first. Ensure that the ground wire is
properly connected to metal parts of the
car’s body. The ground wire of the power
amp and the one of this unit or any other
device must be connected to the car
separately with different screws. If the
screw for the ground wire loosens or falls
out, it could result in fire generation of
smoke or malfunction.
•When replacing the fuse, be sure to only
use a fuse of the rating prescribed on this
product.
•When disconnecting a connector, pull the
connector itself. Do not pull the lead, as
you may pull it out of the connector.
•This product cannot be installed in a
vehicle without ACC (accessory) position
on the ignition switch.
•To avoid short-circuiting, cover the
disconnected lead with insulating tape. It
is especially important to insulate all
unused speaker leads, which if left
uncovered may cause a short circuit.
•For connecting a power amp or other
devices to this product, refer to the
manual for the product to be connected.
•The graphical symbol placed on
the product means direct current.
•When the ignition switch is turned on
(ACC ON), a control signal is output
through the blue/white lead. Connect to
an external power amp’s system remote
control terminal, the auto-antenna relay
control terminal, or the antenna booster
power control terminal (max. 300 mA 12
V DC). The control signal is output
through the blue/white lead, even if the
audio source is switched off.
Important
When this product is in [Power OFF] mode,
the control signal is also turned off. If
[Power OFF] mode is canceled, the control
signal is output again and the antenna is
extended with the auto antenna function
(if the antenna is being used). Be careful so
that the extended antenna does not come
into contact with any obstacles.
Ground wire POWER AMP
Other devices
(Another electronic
device in the car)
Metal parts of car’s
body
*1 Not supplied for this unit
ACC position No ACC position
Notice for the blue/
white lead
â–¶DMH-WT8600NEX/DMH-
WT7600NEX/DMH-WT86NEX/DMH-
WT76NEX/DMH-WC6600NEX/DMH-
WC5700NEX
â–¶DMH-W4660NEX/DMH-W4600NEX
GPS antenna 3.55 m (11 ft. 8 in.)
Microphone 3 m (9 ft. 10-1/8 in.)
iDatalink or Metra adaptor input
Refer to the instruction manual for the
iDataLink or Metra adaptor (sold
separately).
Monitor cable connector*
Connect to LCD screen.
Antenna jack
This product
Pre out supply
Power supply
Fuse (10A)
Wired remote input
Hard-wired remote control adaptor can
be connected (sold separately).
SiriusXM® Connect Vehicle Tuner
Refer to the instruction manual for
SiriusXM Connect Vehicle Tuner (sold
separately).
* Monitor cable and connector are in the front
panel. (DMH-WT8600NEX, DMH-WT7600NEX,
DMH-WT86NEX, DMH-WT76NEX)
•Before using and/or connecting the
iDatalink Maestro adaptor (sold
separately), you will need to first flash the
Maestro module with the appropriate
vehicle and head unit firmware. You can
find the device number that is required
for the activation on the followings (refer
to the Operation Manual.):
–The label on the packaging of this
product
–The label on this product
–The [Firmware Information] screen
•When the iDatalink Maestro adaptor is
connected, use the microphone of this
unit to perform voice operations for
Apple CarPlay, Android Auto, or Amazon
Alexa.
•SiriusXM and all related marks and logos
are trademarks of Sirius XM Radio, Inc. All
rights reserved.
Rear panel (main
terminals)


Product specificaties

Merk: Pioneer
Categorie: Receiver
Model: DMH-WT7600NEX

Heb je hulp nodig?

Als je hulp nodig hebt met Pioneer DMH-WT7600NEX stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Receiver Pioneer

Handleiding Receiver

Nieuwste handleidingen voor Receiver