Phase Technology IW200 Sub Kit Handleiding

Phase Technology Subwoofer IW200 Sub Kit

Lees hieronder de 📖 handleiding in het Nederlandse voor Phase Technology IW200 Sub Kit (4 pagina's) in de categorie Subwoofer. Deze handleiding was nuttig voor 2 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

Thank you for purchasing the Phase Technology

® IW200-

II active in-wall subwoofer and enclosure. These were

engineered to deliver well-dened bass, while remaining

virtually invisible in a room. Its vibration-isolating outer

foam layer virtually eliminates the risk of buzzing and wall

rattling.

The enclosure is designed for installation during new

construction or major remodel jobs to t between framing

studs placed on 16” centers in rooms up to 3,300 cubic

feet in volume. Larger rooms can simply use multiple

IW200-II subwoofers and ampliers.

The enclosure measures at 72” H x 14.4” W x 3.4” D.

The woofer enclosure is for a dual 8” mono woofer system

design that will be powered by the P350 subwoofer

amplier (sold separately).

During pre-wire, you will want to run a pair of wires from

your source location to the woofer location.

Regardless of application, serious audiophile listening or

home theater, we recommend that you take the time to

read this manual thoroughly before connecting speakers

to your amplier or receiver. In the highly unlikely event

that you should experience a problem with set-up or

operation, please contact one of our authorized dealers for

assistance, or contact us directly.

Phase Technology® Corporation

8005 W. 110th St., Suite 208

Overland Park, KS 66210

855.663.5600 (Domestic)

+1.913.663.5600 (International)

913.663.3200 (Fax)

[GETTING STARTED]

FOR EFFICIENT INSTALLATION, YOU WILL NEED THE

FOLLOWING TOOLS:

• ELECTRIC SCREWDRIVER (DRILL) WITH PHILIPS BIT

• TAPE MEASURE

• STUD-FINDER

• SHARP FLAT BLADE SCREWDRIVER

• DRYWALL SAW OR KNIFE

• BUBBLE LEVEL

• PENCIL

SAFETY INSTRUCTIONS 2

INSTALLATION GUIDELINES 3

SPEAKER INSTALLATION 3

CARING FOR YOUR SPEAKER 4

MAINTENANCE AND SERVICE 4

WARRANTY 4

SPECIFICATIONS 4

FLANGE ASSEMBLY

VIBRATION-CANCELING FOAM

IW200 SEALED ENCLOSURE BOX

GRILLE

SELF-ALIGNING CLAMPING SYSTEM

SUBWOOFER/BAFFLE ASSEMBLY

BAFFLE CLAMP SCREWS (6x)

IN-WALL SUBWOOFER

OWNER’S MANUAL: IW200-II

1. Read Instructions - All the safety and operating instructions

should be read before the appliance is operated.

2. Retain Instructions - The safety and operating instructions

should be retained for future reference.

3. Heed Warnings - All warnings on the appliance and in the

operating instructions should be adhered to.

4. Follow Instructions - All operating and other instructions

should be followed.

5. Water and Moisture - The appliance should not be used near

water - for example, near a bathtub, washbowl, kitchen sink,

laundry tub, in a wet basement, or near a swimming pool, etc.

6. Carts and Stands - The appliance should be used only with a

cart or stand that is recommended by the manufacturer.

PORTABLE CART WARNING

7. Wall or Ceiling Mounting - The appliance should be mounted

to a wall or ceiling only as recommended by the manufacturer.

8. Ventilation - The appliance should be situated so that its

location or position does not interfere with its proper ventilation.

For example, the appliance should not be situated on a bed, sofa,

rug, or similar surface that may block the ventilation openings;

or placed in a built-in installation, such as a bookcase or cabinet

[SAFETY INSTRUCTIONS] that may impede the ow of air through the ventilation openings.

9. Heat - The appliance should be situated away from heat sources

such as radiators, stoves, or other appliances that produce heat.

10. Power Source - The appliance should be connected to

a power supply only of the type described in the operating

instructions or as marked on the appliance.

11. Power Cord Protection - Power supply cords should be

routed so that they are not likely to be walked on or pinched by

items placed up or against them, paying particular attention to

cords at plugs, convenience receptacles, and the point where they

exit from the appliance.

12. Cleaning - The appliance should be cleaned only as

recommended by the manufacturer.

13. Nonuse Periods - The power cord of the appliance should

be unplugged from the outlet when left unused for a long period

of time.

14. Object and Liquid Entry - Care should be taken so that

neither objects fall nor liquids spill into the inside of the appliance.

15. Damage Requiring Service - The application should be

serviced by qualied service personnel when:

a. the power supply cord or the plug has been damaged,

b. objects have fallen onto or liquid has been spilled into the

appliance,

c. the appliance has been exposed to rain,

d. the appliance does not appear to operate normally or exhibits a

marked change in performance, or

e. the appliance has been dropped or the cabinet damaged.

16. Servicing - The user should not attempt to service the

appliance beyond those means described in the operating

instructions. All other servicing should be referred to qualied

service personnel.

17. Grounding or Polarization - Precautions should be taken so

that the grounding or polarization means of an appliance is not

defeated.

Explanation of Graphical Symbols

The lightning ash with arrowhead symbol, within an

equilateral triangle, is intended to alert you to the presence

of un-insulated “dangerous voltage: within the product’s

enclosure that may be off sufcient magnitude to constitute

a risk of electric shock to persons.

The exclamation point within an equilateral triangle is

intended to alert you to the presence of important operating

and maintenance (servicing) instructions in the literature

accompanying the appliance.

APPLICABLE FOR USA, CANADA OR WHERE APPROVED FOR

USAGE

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE

PLUG TO WIDE SLOT, INSERT FULLY.

ATTENTION: POUR EVITER LES CHOCS ELECTRIQUES, INTRODUIRE

LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE

CORRESPONDANTE DE LA PRESE ET POUSSER JUSQU AU FOND.

CAUTION: To reduce the risk of electric shock, do not remove cover

(or back). No user-serviceable parts inside. Refer servicing to qualied

service personnel.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

[INSTALLATION GUIDELINES]

When selecting a location to install the woofer, it is recommended the woofer be located near the left and right front speakers, near the oor or ceiling and

close to a side wall. Avoid placing the woofer in the center of the wall, the center of the room, or on an opposite wall whenever possible. Room placement

will affect the output of the IW200-II.

Before beginning your installation, it is recommended that you measure the bay (the space between studs) you intend to install the woofer enclosure.

Although 16” centers are the standard for framing construction, you will likely nd many variations. For the simplest installation and best results, select

a bay that is clear of any obstructions like electrical wiring, gas or water pipes. The woofer enclosure is intended to rest on the bottom plate between

vertical studs. The bottom (toe) plate is the 2” X 4” stud lying on the oor, to which the vertical studs supporting the wallboard are nailed. The height of

the actual woofer in the enclosure was selected to allow the woofer-mounting ange used to mount the subwoofer system, to provide adequate clearance

for decorative base molding up to 6” wide.

Note: Installation of the subwoofers requires six (6) 2 1/2” drywall or deck screws to secure the subwoofer enclosure between the wall studs;

and butt connectors, wire nuts, solder, and electrical tape, or solder and heat-shrink insulation are recommended to make the electrical con-

nections to the amplier (supplied by the installer).

Note: In custom homes, the base molding may be wider than 6” requiring a cutout around the mounting ange. You may wish to raise the

woofer enclosure slightly above the bottom plate. Consult the general contractor if this is a concern.

Choose the appropriate mounting location for each speaker.

NOTE: When deciding upon a location, consider the following:

• Be certain your speaker wires can be run to or are accessible from these locations.

• Make certain the wall or ceiling material is sturdy enough to support the weight and vibration of the speakers.

• Be certain the area behind the speaker is free of obstacles such as wall studs, electrical wiring, pipes, etc.

• Each speaker should be positioned properly, relative to the listening area for good coverage.

[ENCLOSURE AND WOOFER INSTALLATION]

STEP 1: Open each end of the carton and slide the woofer enclosure out of the carton.

Note: Do NOT pull the woofer enclosure from the packing carton using the speaker wires as a handle.

STEP 2: Once the enclosure is placed between the framing, run screws through the stud and into the cabinet. We suggest no less then 6 per side. This

will retain the woofer enclosure in place and prevent it from vibrating against the studs. The wood bafe over the opening in the enclosure is to be used

as a guide for cutting a through hole in the drywall . This needs to be removed after the drywall is up and when you are ready to install the IW 200 (Fig. 1)

Subwoofer Flange and driver assembly into the enclosure.

STEP 3: Once the enclosure is in place you are ready to connect the speaker leads to the amplier leads. The wire in the enclosure is 16-Gauge plenum

rated UL approved stranded copper wire. You may make connections a number of ways including butt-connectors, wire nuts, electrical tape and solder.

Soldered connections with heat-shrink insulation, is the recommend way to splice the amplier and woofer wires. Please note the (+) terminals are

indicated with a red wire.

Note: Low voltage electrical codes differ by state. Check your local low voltage code before selecting a method of wire splicing. The drywall

must be installed with the opening for the speaker to proceed to the next step.

STEP 4: Carefully remove the speaker bafe from the aluminum frame assembly and set aside. Remove the ange assembly from the packing carton.

The ange assembly must make a good seal to insure maximum performance. You will nd two L-shaped foam gasket pieces in the bottom of the carton.

Peel the removable tape from the gasket and stick the adhesive side to the backside of the ange. Upon installation of the ange assembly gasket will

contact the front wall surface to form an airtight seal.

STEP 5: When you remove the ange assembly from the packing carton, you will notice the screws

used to retain the clamp assembly are fully extended. To place the ange assembly into the wall push

the clamp assemblies toward the center of the ange opening; the holes in the ange will allow the

mounting screws to tilt toward the center opening enough to insert the ange assembly into the wall.

Insert the right side into the wall cutout and slide the complete assembly to the right. This will enable

you to then t the left side clamp assembly into the cutout. Center the entire assembly in the opening.

STEP 6: Pinch the self-aligning clamp assembly inside the enclosure until it contacts the backside of

the surface. This will force the three retaining screws to protrude from the front of the ange. Continue

to hold the clamp with one hand and use the electric screwdriver to tighten the center screw of the

ange. Once snug, repeat the procedure on the other clamp assembly. Using your level, verify the

mounting frame is correctly aligned in the opening. Make any necessary adjustments then tighten

the remaining screws until the frame is snug and securely clamping the enclosure board. Avoid over-

tightening the screws.

[FIG. 1]

Product specificaties

Merk:	Phase Technology
Categorie:	Subwoofer
Model:	IW200 Sub Kit

Heb je hulp nodig?

Als je hulp nodig hebt met Phase Technology IW200 Sub Kit stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Subwoofer Phase Technology

Phase Technology Power-FL10 Handleiding

4 Maart 2025

Phase Technology IW-210 Handleiding

4 Maart 2025

Phase Technology IW210 Handleiding

4 Maart 2025

Phase Technology Power-FL12-II Handleiding

4 Maart 2025

Phase Technology IW200 Sub Kit Handleiding

4 Maart 2025

Phase Technology Power FL-8 Handleiding

4 Maart 2025

Phase Technology PL-10p Handleiding

4 Maart 2025

Phase Technology PC-Sub WL12 Handleiding

4 Maart 2025

Phase Technology PL-10s Handleiding

4 Maart 2025

Handleiding Subwoofer

Nieuwste handleidingen voor Subwoofer

Morel Ultimo Powerslim Handleiding

4 Maart 2025

Hifonics Elite HEW8D4S Handleiding

4 Maart 2025

Hifonics Elite HEW10D4S Handleiding

4 Maart 2025

NEAR IGS212M Handleiding

28 Februari 2025

Ecler ARQISSB6Ti Handleiding

26 Februari 2025

Ecler ARQISSB10i Handleiding

26 Februari 2025

Ecler EDGE-SB110P Handleiding

26 Februari 2025

Ecler KICK-SB18 Handleiding

26 Februari 2025

Origin Acoustics CSUB10N Handleiding

25 Februari 2025

Klipsch Reference RW-12 Handleiding

19 Februari 2025