Panasonic WV-SPV781 Handleiding

Panasonic Bewakingscamera WV-SPV781

Lees hieronder de 📖 handleiding in het Nederlandse voor Panasonic WV-SPV781 (4 pagina's) in de categorie Bewakingscamera. Deze handleiding was nuttig voor 23 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

● Switches the MONITOR OUT terminal output between NTSC and PAL.

Included Installation Instructions

PGQX1821YA Cs0615-1075 Printed in China

Two-dimensional

matrix barcode

(Data Matrix):

To our website

IMPORTANT:

● Also waterproof the F 2P power cable (accessory),

E 4P alarm cable (accessory), and external connec-

tions in the same way.

● Stretch the tape to approx. twice its length (see the

illustration) and wind it around the cable. Insufficient

tape stretch causes insufficient waterproofing.

● To prevent the LAN cable hook from coming loose

easily, fit the D LAN connector cover (accessory)

onto the pigtail cable as illustrated, and then slide it in

the direction indicated by the arrow. The connector of

the LAN cable used with this camera must meet the

following restrictions.

Height when inserted (From bottom to hook.):

Max. 16 mm {5/8 inches}

Connector width: Max. 14 mm {9/16 inches}

● To install this product outdoors, be sure to waterproof

the cables.

Waterproof grade (IEC IP66 or equivalent) is applied

to this product only when it is installed correctly as

described in these operating instructions and appro-

priate waterproof treatment is applied.

The camera mount bracket is not waterproof.

Installation Guide

Network Camera

Model No. WV-SPV781L

● This manual describes the installation procedures, network camera installation, cable

connections, and eld-of-view adjustment.

● Before reading this manual, be sure to read the Important Information.

Major operating controls

The component names of the camera are as follows. Refer to the illustration when

installing or adjusting the camera.

Standard accessories Making connections

Important Information ............................... 1 pc.

Warranty card ........................................... 1 set

Code label*2 .............................................. 1 pc.

Installation Guide (this document) ............ 1 set

CD-ROM*1 ................................................. 1 pc.

Camera caution label................................ 1 pc.

The CD-ROM contains the operating instructions and different kinds of tool software programs.

*2 This label may be required for network management. The network administrator shall retain

the code label.

*3 The audio/monitor output cable can be switched to be used as MONITOR OUT using the

software. The MONITOR OUT conversion plug is used to connect the camera to the audio/

monitor output cable and to convert a stereo mini jack (ø3.5 mm) {1/8 inches} into an RCA pin

output jack.

A Camera mount bracket cover ........... 2 pcs.

B Camera mount bracket cover fixing screw

(M3 x 6 mm {1/4 inches}) ................... 3 pcs.

(incl. 1 spare)

C Waterproof tape .................................. 1 pc.

D LAN connector cover ........................... 1 pc.

E 4P alarm cable .................................... 1 pc.

F 2P power cable .................................... 1 pc.

G MONITOR OUT conversion plug*3 ....... 1 pc.

H Safety wire .......................................... 1 pc.

I Wire lug fixing screw

M3 x 10 mm {3/8 inches} .................... 2 pcs.

(incl. 1 spare)

J Safety wire lug ..................................... 1 pc.

K Protection cover ................................... 1 pc.

L Adapter box .......................................... 1 pc.

M Mounting screws for adapter box (M5 × 20

mm {13/16 inches}) ............................. 5 pcs.

(of them, 1 for spare)

N Adapter box mounting screw

(M4 × 35 mm {1- 3/8 inches}) ............... 1 pc.

● How to initialize the camera

Follow the steps below to initialize the network camera.

1 Turn off the power of the camera. When using a PoE hub, disconnect the LAN cable from the camera.

When using an external power supply, disconnect the 2P power cable plug from the camera.

Turn on the power of the camera while holding down the INITIAL SET button, and then keep holding

down the button for 5 seconds or more. About 2 minutes after you have released the INITIAL SET but-

ton, the camera will start up and the settings including the network settings will be initialized.

● When data is being sent via the network camera Blinks green (accessing)

Turn off each system’s power supply before making a connection. Before making connections,

prepare the required peripheral devices and cables.

● When the camera is able to communicate with the Lights orange

connected device

● When an SD memory card is inserted and could Lights off → Blinks green →

be recognized Lights off

● When data can be saved after the SD memory card is inserted Lights off → Lights green

and the SD ON/OFF button is pressed (for less than 1 second)

● When data can be saved to the SD memory card Lights green

● When the SD memory card is removed after holding down

Lights green → Blinks green →

the SD ON/OFF button for about 2 seconds Lights off (recording)

Lights green →

Lights off (waiting for recording)

● When data cannot be saved to the SD memory card because Lights off

an abnormality was detected or the SD memory card is

configured not to be used

● When AF (Auto Focus) operation is being executed

Blinks red (about once per second)

● When the camera is being started Lights red

● When an SD memory card is recognized normally

Lights red → Lights off

● When the SD memory card slot is not used or an abnormality Lights red → Stays red

is detected in SD memory card after the camera has started

IMPORTANT:

● When the camera is initialized, the settings including the network settings will be initialized.

Note that the CRT key (SSL encryption key) used for the HTTPS protocol will not be initialized.

● Before initializing the settings, it is recommended to write down the settings in advance.

● Do not turn off the power of the camera during the process of initialization. Otherwise, it may

fail to initialize and may cause malfunction.

IMPORTANT:

● Use all 4 pairs (8 pins) of the LAN cable (category 5 or better, straight).

● The maximum cable length is 100 m {328 feet}.

● Make sure that the PoE device in use is compliant with IEEE802.3af standard.

● When connecting both the 12 V DC power supply and the PoE device for power sup-

ply, 12 V DC will be used for power supply*.

* If a 12 V DC power supply and a PoE hub or router are used at the same time, net-

work connections may not be possible. In this case, disable the PoE settings. Refer

to the operating instructions of the PoE hub or router in use.

* Depending on the PoE device used, if you stop the 12 V DC power supply after

operating it and a PoE hub or router at the same time, the power supply may stop,

causing the camera to restart.

● When the LAN cable is disconnected once, reconnect the cable after around 2 sec-

onds. When the cable is quickly reconnected, the power may not be supplied from

the PoE device.

● When cables are used outdoors, there is a chance that they may be affected by light-

ning. In this case, install a lightning arrester just before where the LAN cable con-

nects to the camera.

Connect a LAN cable (category 5 or better, straight)

Waterproof treatment for the cable joint sections

When connecting to a network using a PoE hub

Microphone/line input cable

Connect a stereo mini plug (ø3.5 mm {1/8 inches}).

● Input impedance: Approx. 2 kΩ (unbalanced)

● Recommended cable length: Less than 1 m {3.28 feet} (for microphone input) Less than

10 m {32.8 feet} (for line input)

● Recommended microphone: Plug-in power type (option)

• Supply voltage: 2.5 V ±0.5 V

• Recommended sensitivity of microphone: -48 dB ±3 dB (0 dB=1 V/Pa,1 kHz)

● Input level for line input: Approx. -10 dBV

* Use an external powered speaker.

Connect an external amplifier-embedded speaker to the audio/

monitor output cable

Connect a stereo mini plug (ø3.5 mm {1/8 inches}).*

● Output impedance: Approx. 600 Ω (unbalanced)

● Recommended cable length: Less than 10 m {32.8 feet}

● Output level: -20 dBV (can switch to monitor output)

IMPORTANT:

● Connect/disconnect the audio cables and turn on the power of the camera after turn-

ing off the power of the audio output devices. Otherwise, loud noise may be heard

from the speaker.

● Make sure that the stereo mini plug is connected to this cable. When a monaural mini

plug is connected, audio may not be heard. When connecting a monaural speaker

with amplifier, use a locally procured conversion cable (mono-stereo).

Adequate waterproof treatment is required for the cables when installing the camera with cables

exposed or installing it under the eaves.

The camera body is waterproof, but the cable ends are not waterproof. Be sure to use the sup-

plied waterproof tape at the points where the cables are connected to apply waterproof treatment

in the following procedure.

Failure to observe this or use of a tape other than the provided waterproof tape (such as a vinyl

tape) may cause water leakage resulting in malfunction.

Before starting the installation, check the entire system conguration.

The following illustration gives a wiring example of how to connect the camera to the network via

a PoE device (hub).

<LAN cable> < Alarm input/output cable, power cable, micro-

phone/line input cable, audio/monitor output

cable>

Stretch the tape to

approx. twice its length.

2 x

IMPORTANT:

● The adjustment monitor is used to adjust the field of view when installing or servicing

the camera. It is not provided for recording/monitoring use.

● Depending on the adjustment monitor, some characters (camera title, preset ID, etc.)

may not be displayed on the screen.

● Use a switching hub or a router which is compliant with 10BASE-T/100BASE-TX.

● If a PoE hub is not used, each network camera must be connected to a 12 V DC

power supply.

● When using 12 V DC, power supply from a PoE hub or router is not required.

The hook engages

with the connector

terminal

D LAN connector cover

(accessory)

Sunshield

TILT lock screw

Camera

Arm

K Protection

cover (installed)

Front cover

Camera

Yawing

lock screw

H Safety wire

(accessory)

PAN lock screws

(2 pcs: The other is on the

opposite side)

L Adapter

box

(accessory)

A Camera mount

bracket covers

(2 pcs.) (accessory)

Camera

mount bracket

*1 SDXC/SDHC/SD memory card is described as SD memory card.

*2 Depending on the scanning application used, the Data Matrix may not be

able to be read correctly. In this case, access the site by directly entering the

following URL.

http://security.panasonic.com/pss/security/support/qr_sp_select.html

Connect the power cable

IMPORTANT:

● Use 12 V DC power supply that is insulated from the commercial AC power.

● Be sure to use the F 2P power cable (accessory) provided with this product.

● Be sure to fully insert the F 2P power cable (accessory) into the 12 V DC power sup-

ply terminal. Otherwise, it may damage the camera or cause malfunction.

● When installing the camera, make sure that excessive force is not applied to the

power cable.

● Be sure to use an AC adaptor compliant with the specifications (written in the indication

label on the bottom side of this unit) regarding power source and power consumption.

Power cable

12 V DC

Red Positive

Black Negative

LAN cable (category 5 or better, straight)

Use a LAN cable (category 5 or better, cross) when directly connecting the camera to a PC.

Note:

● Off, input, and output of the external I/O terminal 2 and 3 can be switched by configur-

ing the setting. Refer to the Operating Instructions on the provided CD-ROM for further

information about the external I/O terminal 2 and 3 (ALARM IN2, 3) settings (“Off”,

“Alarm input”, “Alarm output”, “AUX output” or “DAY/NIGHT switching output”).

IMPORTANT:

● Be sure to use the E 4P alarm cable (accessory) provided with this product.

● Install external devices so that they do not exceed the ratings above.

● When using the external I/O terminals as the output terminals, ensure they do not

cause signal collision with external signals.

Connect the alarm input/output cable

● ALARM IN1 (DAY/NIGHT IN), ALARM IN2, ALARM IN3

Input specification: No-voltage make contact input (4 V - 5 V DC, internally pulled up)

OFF: Open or 4 V - 5 V DC

ON: Make contact with GND (required drive current: 1 mA or more)

● ALARM OUT, AUX OUT (DAY/NIGHT OUT)

Output specification: Open collector output (maximum applied voltage: 20 V DC)

Open: 4 V - 5 V DC by internal pull-up

Close: Output voltage 1 V DC or less (maximum drive current: 50 mA)

* The default of EXT I/O terminals is “Off”.

E4P alarm cable (accessory)

PoE device (hub)

Adjustment monitor

LAN cable

(category 5 or better, straight)

Microphone

Powered

speaker

Analog monitor

SD memory card

slot

1 When the SD ON/OFF button is pressed for less than 1 second, the SD MOUNT indicator is lit green

and data can be saved to the SD memory card

2 When the SD ON/OFF button is held down for about 2 seconds, the SD MOUNT indicator goes out,

and the SD memory card can be removed.

For U.S. and Canada:

Panasonic System Communications

Company of North America,

Unit of Panasonic Corporation

of North America

www.panasonic.com/business/

For customer support, call 1.800.528.6747

Two Riverfront Plaza, Newark, NJ 07102-5490

Panasonic Canada Inc.

5770 Ambler Drive, Mississauga,

Ontario, L4W 2T3 Canada

(905)624-5010

www.panasonic.ca

For Europe and other countries:

Panasonic Corporation

http://www.panasonic.com

Panasonic System Networks Co., Ltd.

Fukuoka, Japan

Authorised Representative in EU:

Panasonic Testing Centre

Panasonic Marketing Europe GmbH

Winsbergring 15, 22525 Hamburg, Germany

The following parts are used during installation procedures.

GND (black)

ALARM IN3, AUX OUT, DAY/NIGHT OUT (gray)

(Alarm input 3, AUX output, DAY/NIGHT switching output)

ALARM IN2, ALARM OUT (red) (Alarm input 2, Alarm output)

ALARM IN1, DAY/NIGHT IN (green) (Alarm input 1/ DAY/NIGHT switching input)

RJ45 (female)

Network cable

LAN cable

(category 5 or better, straight)

E 4P alarm cable

(accessory)

Alarm input/output cable

(External I/O terminal)

Power cable

(12 V DC)

F 2P alarm cable

(accessory)

Microphone/line input cable (white)

Audio/monitor output cable (black)

Caution:

● A READILY ACCESSIBLE DISCONNECT DEVICE SHALL

BE INCORPORATED TO THE EQUIPMENT POWERED

BY 12 V DC POWER SUPPLY.

● ONLY CONNECT 12 V DC CLASS 2 POWER SUPPLY (UL

1310/CSA 223) or LIMITED POWER SOURCE (IEC/EN/

UL/CSA 60950-1).

Wind the tape in a

half-overlapping manner. Wind the tape in a

half-overlapping

manner.

12 V DC

(red)

GND

(black)

Note:

● Use a thin, non-conductive tool to press the switch.

Waterproof tape (accessory)

Connect the output cable of the AC adaptor to the

2P power cable (accessory).

Side B (Upper)

Side A (lower)

Rating label

Dehumidifying

device

MONITOR OUT jack

(Video Out terminal

Default:

For NTSC monitor)

NTSC/PAL switch

INITIAL SET button

SD ON/OFF button

SD MOUNT indicator

SD ERROR/AF indicator

ACT indicator

LINK indicator

AF (Auto Focus)

button

TELE button

(The camera zooms in.)

WIDE button

(The camera zooms out.)

Pass the

safety wire (accessory)

through the wire mounting hole in

the Safety wire lug (accesso-J

ry).

Wire mounting hole

Installation

Step 2 Attaching the safety wire

Step 4 Adjusting the camera , , , , 12345

Step 4 Adjusting the camera (continued)

Step1 Preparations

The installation tasks

are explained using

5 steps.

There are 3 methods to install the camera to a ceiling or wall as described below. Prepare the

required parts for each installation method before starting the installation. The following are the

requirements for the various installation methods.

Installation method

Recom-

mended

screw

Minimum pull-

out strength

[1] Directly mount the camera onto the ceiling or wall

(when there is a space for wiring in the ceiling or

the wall)

screws x 4

724 N

{163 lbf}

(per 1 pc.)*1

[2]

Mount the camera to a junction box

* Only use metal junction boxes.

screws x 4*2

724 N

{163 lbf}

(per 1 pc.)*1

[3]

Mount the camera onto the ceiling or wall using the

adapter box (approx. 510 g {1.13 lbs})

(when there is no space for wiring in the ceiling or the wall)

screws x 4

724 N

{163 lbf}

(per 1 pc.)*1

*1 To mount the camera onto the ceiling or wall, the safety wire (accessory) H

must be attached. Have an M6 bolt and nut or anchor (with the minimum pull-

out strength of 724 N {163 lbf}) ready for securing the safety wire.

Prepare a M4 screw with a washer with a diameter of 7.5 mm {5/16 inches} to

10 mm {3/8 inches} and a spring washer.

IMPORTANT:

● For the screws or anchor bolts used in the above methods ([1] to [3]), be sure to secure

the minimum pull-out strength of 724 N {163 lbf} per screw or bolt.

● Select screws according to the material of the ceiling or wall that the camera will be

mounted to. In this case, wood screws and nails should not be used.

● If a ceiling or wall board such as plaster board is too weak to support the total weight,

the area shall be sufficiently reinforced.

● Because the front cover is temporarily removed when installing or adjusting the camera,

make sure no liquid enters the camera at these times.

Determine the position where the camera is to be mount-

ed on the ceiling or wall and drill a hole for securing the

camera and wiring as shown in the illustration to the right.

* Determine the diameter and depth of the hole according to the

size of fixing screws or anchors (4 M5 screws, locally procured).

2 Connect the cables coming from the camera and com-

ing through the ceiling or wall according to the instruc-

tions in “Making connections”. Waterproof the connec-

tions according to the instructions in “Waterproof treat-

ment for the cable joint sections”.

Secure the camera to the camera mount bracket by attaching the 2 upper M5 screws or anchors

(M5 x 4, locally procured) and then the 2 lower ones into the holes on side B on the camera mount

bracket in the order shown in the illustrations above explanations [1]-1 to [1]-3 in the lower left.

Secure the

camera mount bracket cover (accessory) to the camera mount bracket by

using M3

6 mm {1/4 inches}

Camera mount bracket cover fixing screws (accessory).

2 Fit the Safety wire lug to the camera.

1 Change the direction the camera is facing from directly down to facing up (as shown in the illustration

on the lower right) and temporarily x the camera in place. After this, loosen the 4 xing screws on the

camera front cover and remove the front cover together with the

Protection cover (accessory).

Insert an SD memory card into the slot, if necessary.

Insert the SD memory card with its label facing the lens.

2 Fit a pin cable (locally procured) to the

MONITOR OUT jack on the camera and

connect an adjustment monitor.

6 After adjusting the focus by pressing the AF

button, remove the adjustment monitor.

Remove the Protection cover (accessory).K

When the installation of the camera is complete, perform camera settings while

referring to the included “Congure the settings of the camera” (leaet).

Attach the front cover.

8 Secure the safety wire (accessory) to H

the ceiling or wall.

IMPORTANT:

● Securely tighten the 4 front cover fixing

screws. Failure to do so may cause the cam-

era to fall or waterproof failure.

Recommended tightening torque: 0.6 N·m

{0.44 lbf·ft}

■ When the camera is installed to the ceiling

■ When the camera is mounted on the wall

5 Adjust the camera eld of view.

Note:

● Any of the PAN, TILT and YAW lock screws can be adjusted by loosening them about

1 turn. Do not unscrew them more than necessary.

● Make sure the camera is supported when loosening screws and adjusting the direction

of the camera.

● When the image size is adjusted using the WIDE or TELE button, the camera focus is

adjusted accordingly by the auto-focus coarse adjustment function.

● When the camera is mounted on the wall, adjust the camera direction by turning the PAN,

TILT and YAW parts as shown in the illustration below.

● The range of angles that the camera can actually be turned to in regards to a wall or ceiling

is as follows.

Wall mounting Ceiling mounting

Angle Adjustment part Angle Adjustment part

Horizontal ±115° TILT rotation

part*

±180° PAN rotation

part

Vertical ±115° TILT rotation

part*

0° to 115° TILT rotation

part

Yaw from -115° to

+200

YAW rotation

part

from -115° to

+200

YAW rotation

part

* You can change between horizontal and vertical angles by adjusting the PAN

rotation part.

IMPORTANT:

●

The front cover is connected to the camera via

the auxiliary wire for mounting the front cover

as well as the IR LED cable. Do not remove

the auxiliary wire and IR LED cable.

● Do not remove the K Protection cover (acces-

sory) from the front cover.

IMPORTANT:

● Avoid touching the tilting part near the warning label

when you change the tilting angle to secure the cam-

era.

● If the TILT or PAN lock screw is loosened, the camera

may not be held in place when it is secured to the

wall or ceiling. If this is the case, temporarily tighten

the appropriate lock screws to keep the camera from

moving.

IMPORTANT:

● Once the front cover is installed, the camera

may be slightly out of focus. After installing

the front cover and K Protection cover

(accessory), use the auto focus via the set-

tings menu.

IMPORTANT:

● After adjustment, be sure to tighten the PAN, TILT and Yawing lock screws.

IMPORTANT:

● Each M6 bolt and nut or anchor (locally procured) for securing the

H safety wire (acces-

sory) must have the minimum pull-out strength of 724 N {163 lbf}.

● Be sure to secure the

H safety wire (accessory) to the foundation of a structure or an

area that is strong enough.

● Be sure to install the camera at least 2m 80 cm {9.2 feet} from the floor (the distance

between the lowest part of the installed camera and the floor).

● When installing on a wall, secure the

H safety wire (accessory) to an area above the

camera and the location where the camera is installed.

● Attach the H safety wire so that if the camera were to become detached, it would not fall

on nearby people.

Step1

Preparations

Step2

Attaching the safety

wire

Step3

Fixing the camera

Step4

Adjusting the camera

Step5

Perform camera settings

(see the separate leaet)

L Adapter box

(accessory)

↑TOP/FRONT mark

(on the front)

Camera mount

bracket

Side B (upper)

Side B

(Upper)

M5 x 2

(locally

procured)

M5 x 2

(locally procured)

Junction

box

↑ TOP/FRONT mark

2 PAN lock

screws

(the other one is

on the opposite

side)

A Camera mount bracket cover (accessory)

Camera mount

bracket cover fixing

screws

(accessory)

N Adapter box mounting screw (accessory)

M4 × 35 mm {1- 3/8 inches}

J Safety wire lug

(accessory)

H Safety wire

(accessory) Wire fitting

I Wire lug fixing screw

(accessory) Recommended tightening torque:

0.6 N·m {0.44 lbf·ft}

* The safety wire is not shown in the

subsequent illustrations.

● To remove the SD memory card, hold down

the SD ON/OFF button for about 2 seconds.

When the blinking SD MOUNT indicator goes

out, you can remove the SD memory card.

● After the SD memory card has been

replaced, press the SD ON/OFF button (for

less than 1 second), and make sure the SD

MOUNT indicator is continually lit.

● If you do not press the SD ON/OFF button after

replacing the SD memory card, the SD MOUNT indi-

cator is automatically lit approximately 5 minutes later.

Adjust the direction of the camera with the PAN, TILT and YAW parts, and press the

WIDE or TELE button until the desired field of view is achieved.

Using a 5 mm {3/16 inches} hex wrench (locally procured), loosen the PAN lock screw on

either side of the base of camera arm. To direct the camera to the left, turn the screw

clockwise when viewed from the front. To direct the camera to the right, turn it counter-

clockwise. (Panning range: + 180° to - 180°)

B) Using a 5 mm {3/16 inches} hex wrench (locally procured), loosen the TILT lock screw

in the center of camera arm and roughly adjust the direction of the camera. (Tilting

range: 0° to 115°)

C) Temporarily tighten 2 PAN lock screws and 1 TILT lock screw to prevent the camera

from moving.

D) Using a 5 mm {3/16 inches} hex wrench (locally procured), loosen the Yawing lock

screw, turn the camera until the sunshield faces up and adjust the tilt of the cam-

era.

(Yaw range: -115° to +200°)

E) Press the WIDE or TELE button to adjust the field of view.

F) Adjust the camera angle and field of view by repeating steps A) through E). When

the desired angle and field of view are achieved, tighten the 2 PAN lock screws,

TILT lock screw and Yawing lock screw.

Recommended tightening torque

PAN lock screw: 2.7 N·m {2.0 lbf ft}

TILT lock screw: 4.3 N m {3.2 lbf ft}

Yawing lock screw: 2.7 N m {2.0 lbf ft}

J Safety wire lug

(accessory)

Step 3 Fixing the camera

[1] Directly mount the camera onto the ceiling or wall

Note:

● When installing on a wall, install the

camera mount bracket so that “↑ TOP/

FRONT” faces upward.

● When installing on a ceiling, install the

camera mount bracket so that “↑ TOP/

FRONT” is aligned with the direction in

which the camera is pointed.

Step 3 Fixing the camera (continued from upper right)

[1]-1

Loosen the TILT lock

screw by about 1 turn until

the camera faces downward

and then temporarily tighten

the TILT lock screw. After

this, use the 2 upper M5

screws (locally procured) to

secure the camera.

[1]-2 Loosen the 2 PAN

lock screws about 1

turn until the camera

faces upward and use

the 2 lower M5

screws (locally pro-

cured) to secure the

camera.

[1]-3 Using the camera mount B

bracket cover fixing screws

(accessory), install the A

camera mount bracket cover

(accessory) with the camera

facing downward.

Recommended tightening torque:

0.6 N·m {0.44 lbf ft}

Secure the adapter box to the wall.

● Drill pilot holes and a cable hole (see the illus-

tration to the left for their dimensions). (Drill

pilot holes only if making connections through

the cable hole from the side.)

● Be sure to face “TOP” inside the adapter box

upward.

● Use 4 screws (locally procured) to directly secure

the adapter box to the wall. Minimum pull-out

strength: 724 N {163 lbf} (per 1 pc.)

● To install this product outdoors, be sure to

waterproof the screws and their holes.

Temporarily secure the camera mount bracket

and camera to the adapter box.

● After referring to [1]-1 and adjusting the camera to

face down, temporarily secure the camera, and then

use the M4 × 35 mm {1- 3/8 inches} N Adapter box

mounting screw (accessory) for installing the camera

to temporarily install the camera mount bracket to the

left or right hinge of the adapter box so that it can be

opened and closed.

● Secure the camera mount bracket with “↑TOP/

FRONT” facing upward.

● When the wall is on one side or the other,

install the adapter box to the hinge on the

opposite side of the wall.

● Secure the camera mount bracket to the hinge

of the adapter box using the following tighten-

ing torque. Recommended tightening torque:

0.78 N·m {0.58 lbf·ft}

3 Connect the cables.

● Connect the cables coming from the camera and

coming through the wall according to the instruc-

tions in “Making connections”.

● Waterproof the connections according to the

instructions in “Waterproof treatment for the

cable joint sections”.

4 Secure the camera mount bracket to the

adapter box.

● Using 4 M5 x 20 mm {13/16 inches} M

Mounting screws for adapter box (accessory),

secure the camera mount bracket to the

adapter box via the holes in side A of the cam-

era mount bracket in the order of the top 2

holes to bottom 2 holes. Recommended tight-

ening torque: 1.86 N·m {1.37 lbf ft}

(Refer to [1]-1 and [1]-2.)

● Using 2 M3 x 6 mm {1/4 inches} B camera mount

bracket cover fixing screws (accessory), secure

the A Camera mount bracket cover (accessory)

to the Camera mount bracket. Recommended

tightening torque: 0.6 N·m {0.44 lbf ft}

* The following explains an example of

mounting the camera on a wall.

[2] Mount the camera to a junction box

[3] Mount the camera onto the ceiling or wall using the Adapter box (accessory)L

As shown in the illustration to the right,

install the camera to a junction box using

4 M4 xing screws (locally procured) via

the holes in side B of the camera mount

bracket. (Minimum pull-out strength:

724 N {163 lbf} (per 1 pc.))

Note:

● The procedure for fitting screws in the holes

for connections and fixing screws is the

same as for 2, 3, and

4 in [1] Directly

mount the camera onto the ceiling or wall.

● When junction boxes or the like are used, it

is recommended that 2 pieces be used side

by side. (Securing the camera to one junction

box and making connections to the other

makes cable connections easy.)

Camera

mount bracket

TOP

46 mm {1-13/16 inches}

83.5 mm

{3-5/16 inches}

24.5 mm

{15/16 inches}

6 mm {1/4 inches} wide x

10 mm {3/8 inches}

length hole

Cable access hole

(Used when connecting to a conduit.

Supports G3/4 parallel screws.)

Screws x 4

(M5, locally

procured)

Center of the adapter

box

Cable access hole

View from above (internal)

L Adapter box

(accessory)

ø30 mm

{1-3/16 inches}

23 mm {29/32 inches}

Camera mount

bracket cover fixing

screws (accessory)

x 2

M6 bolt and nut or anchor

(locally procured)

H Safety wire

(accessory)

H Safety wire

(accessory) H Safety wire

(accessory)

Auxiliary

wire

Front cover

Front cover fixing screws

Protection cover

retaining tape

K Protection cover

(accessory)

Front cover fixing screws

Mounting screws for

adapter box(accessory) x 4

Side A

(lower)

A Camera mount

bracket cover (acces-

sory) x 2

PAN lock screws

(The other one is on

the opposite side) x 2

YAWr totationpar

TILTr totationpar

PANrotationpart

Cameraa trmpar

Yawing

lock screw x 1

Tilt lock screw x 1

* The front cover, including cables and wires, and Protection

cover are not shown in the illustration.

When the camera has been installed, remove

the protection cover from the front cover. After

removal, be sure not to touch the clear part of

the front cover.

Note:

● When removing the camera, perform removal by following the installation procedure in

the reverse order.

● After the installation is complete, store the

K Protection cover (accessory) for use dur-

ing servicing.

Step 5 Configuring the settings of the camera (see the leaflet)

Auxiliary

wire

Front cover

Protection cover

retaining tape

K Protection cover

(accessory)

K Protection cover

(accessory)

Clear part of the

front cover

46 mm

{1-13/16 inches}

83.5 mm

{3-5/16 inches}

35 mm

{1-3/8 inches}

Cable access

hole ø30 mm

{1-3/16 inches}

23 mm

{29/32 inches}

* M5 x 4 screws, Minimum pull-out strength: 724 N {163 lbf} (per 1 pc.). Secure the

camera through the holes in side B of the camera mount bracket.

46 mm

{1-13/16 inches}

83.5 mm

{3-5/16 inches}

SD memory card

(Ensure that the label

faces the lens.)

The front cover, including the cables and wires,

and the front cover protector are not shown in

the subsequent illustrations.

H Safety wire

(accessory)

M6 bolt and nut or anchor

(locally procured)

CeilingCeiling

Wall

Warning label

Camera

mount

bracket

Note:

● When closing the front cover, be sure not to

allow the IR LED cable to be caught in the

cover.

Direction in which

“↑TOP/FRONT” is pointed

Direction in which the

camera is pointed

Example: When mounting on a ceiling

3 Turn on the camera.

TILT lock

screw

hinges

* Do not adjust the PAN

rotation part more than

±180°. This may cause

cables to be wrenched.

Product specificaties

Merk:	Panasonic
Categorie:	Bewakingscamera
Model:	WV-SPV781

Heb je hulp nodig?

Als je hulp nodig hebt met Panasonic WV-SPV781 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Bewakingscamera Panasonic

Panasonic AW-HE20KE Handleiding

27 Maart 2024

Panasonic AW-UE100K Handleiding

15 November 2023

Panasonic AW-UR100 Handleiding

4 Juli 2023

Panasonic WV-U2540L Handleiding

29 April 2023

Panasonic WV-U1132 Handleiding

28 April 2023

Panasonic WV-SF438E Handleiding

20 April 2023

Panasonic AW-HN40H Handleiding

7 April 2023

Panasonic AW-UE150WE Handleiding

17 Maart 2023

Panasonic AW-UE50 Handleiding

12 Maart 2023

Panasonic AW-HR140 Handleiding

25 Februari 2023

Handleiding Bewakingscamera

Nieuwste handleidingen voor Bewakingscamera

Honeywell HC35WE5R3 Handleiding

20 December 2024

Honeywell Performance H4W8PER2V Handleiding

20 December 2024

Hikvision DS-2CE12KF3T-LS Handleiding

18 December 2024

Hikvision DS-2CE78D0T-LXTS/A Handleiding

18 December 2024

TP Link VIGI C450 Handleiding

18 December 2024

Hikvision DS-2CE76U0T-LPF Handleiding

18 December 2024

Hikvision DS-2CE78U0T-LF Handleiding

18 December 2024

Hikvision DS-2CE16U0T-LPF Handleiding

18 December 2024

Hikvision DS-2CE72KF3T-LSYE Handleiding

18 December 2024

Hikvision DS-2CE17U0T-LF Handleiding

18 December 2024