Panasonic WV-S6131 Handleiding

Panasonic Bewakingscamera WV-S6131

Lees hieronder de 📖 handleiding in het Nederlandse voor Panasonic WV-S6131 (4 pagina's) in de categorie Bewakingscamera. Deze handleiding was nuttig voor 62 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

Network Camera

Model No. WV-S6131 / WV-S6111

Installation Guide

Included Installation Instructions

Important safety instructions

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including

amplifiers) that produce heat.

9) Only use attachments/accessories specified by the manufacturer.

10) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the

apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury

from tip-over.

S3125A

11) Unplug this apparatus during lightning storms or when unused for long periods of time.

12) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been dam-

aged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have

fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally,

or has been dropped.

Troubleshooting

Open Source Software

• This product contains open source software licensed under GPL (GNU General Public License),

LGPL (GNU Lesser General Public License), etc.

• Customers can duplicate, distribute and modify the source code of the software under license of

GPL and/or LGPL.

• Refer to the “readme.txt” file on the provided CD-ROM for further information about open source

software licenses and the source code.

• Please note that Panasonic shall not respond to any inquiries regarding the contents of the source

code.

The model number and serial number of this

product may be found on the surface of the unit.

You should note the model number and serial

number of this unit in the space provided and

retain this book as a permanent record of your

purchase to aid identification in the event of

theft.

Model No.

Serial No.

NOTE: This equipment has been tested and found

to comply with the limits for a Class A digital

device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable

protection against harmful interference when the

equipment is operated in a commercial environ-

ment. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed

and used in accordance with the instruction man-

ual, may cause harmful interference to radio com-

munications.

Operation of this equipment in a residential area is

likely to cause harmful interference in which case

the user will be required to correct the interfer-

ence at his own expense.

FCC Caution: To assure continued compliance,

(example - use only shielded interface cables

when connecting to computer or peripheral devic-

es). Any changes or modifications not expressly

approved by the party responsible for compliance

could void the user’s authority to operate this

equipment.

For U.S.A.

CAN ICES-3(A)/NMB-3(A)

For Canada

WARNING:

• To prevent injury, this apparatus must be secure-

ly attached to the wall/ceiling in accordance with

the installation instructions.

• To prevent fire or electric shock hazard, do not

expose this apparatus to rain or moisture.

• The apparatus should not be exposed to drip-

ping or splashing.

• All work related to the installation of this product

should be made by qualified service personnel

or system installers.

• The installation shall be carried out in accor-

dance with all applicable installation rules.

• The connections should comply with local elec-

trical code.

• Batteries (battery pack or batteries installed)

shall not be exposed to excessive heat such as

sunlight, fire or the like.

CAUTION:

• Any changes or modifications not expressly

approved by the party responsible for compli-

ance could void the user’s authority to operate

the equipment.

• The network camera is only intended for a con-

nection to an ethernet or PoE network without

routing to the outside plant.

Disposal of Old Equipment and Batteries

Only for European Union and countries with recycling systems

These symbols on the products, packaging, and/or accompanying documents mean that used

electrical and electronic products and batteries must not be mixed with general household waste.

For proper treatment, recovery and recycling of old products and used batteries, please take them

to applicable collection points in accordance with your national legislation.

By disposing of them correctly, you will help to save valuable resources and prevent any potential

negative effects on human health and the environment.

For more information about collection and recycling, please contact your local municipality.

Penalties may be applicable for incorrect disposal of this waste, in accordance with national

legislation.

Note for the battery symbol (bottom symbol)

This symbol might be used in combination with a chemical symbol. In this case it complies with the

requirement set by the Directive for the chemical involved.

About the user manuals

Product documentation is composed of the following documents.

• Installation Guide (this document): Explains installation, cable connections, mounting and removal. This

manual uses the WV-S6131 as an example in the explanations.

• Important Information (included in the CD-ROM):

Provides basic information about the product.

• Operating Instructions (included in the CD-ROM): Explains how to perform the settings and how to oper-

ate this camera.

Adobe® Reader® is required to read these operating instructions on the provided CD-ROM.

When the Adobe Reader is not installed on the PC, download the latest Adobe Reader from the Adobe web site

and install it.

The external appearance and other parts shown in this manual may differ from the actual product within the

scope that will not interfere with normal use due to improvement of the product.

Standard accessories

Installation Guide (this document) 1 set ........................

IMPORTANT SAFETY INSTRUCTIONS 1 pc. ...............

Warranty card*1 ...................................................1 set

CD-ROM*2 .......................................................... 1 pc.

Code label*3........................................................ 1 pc.

*1 This product comes with several types of warranties. Each warranty is only applicable to the products pur-

chased in the regions indicated on the relevant warranty.

*2 The CD-ROM contains the operating instructions and different kinds of tool software programs.

*3 This label may be required for network management. Use caution not to lose this label.

Before requesting service, refer to the Important Information (included in the CD-ROM) and

“Troubleshooting” in the Operating Instructions (included in the CD-ROM) and confirm the

trouble.

: Direct current symbol

• Before attempting to connect or operate this product, please read these instructions carefully and

save this manual for future use.

• For information about the basic description of this product, refer to the Important Information on

the provided CD-ROM. For information about how to perform the settings and how to operate the

camera, refer to the Operating Instructions on the provided CD-ROM.

• The model number is abbreviated in some descriptions in this manual.

For U.S. and Canada:

Panasonic System Communications

Company of North America,

Unit of Panasonic Corporation

of North America

www.panasonic.com/business/

For customer support, call 1.800.528.6747

Two Riverfront Plaza, Newark, NJ 07102-5490

Panasonic Canada Inc.

5770 Ambler Drive, Mississauga,

Ontario, L4W 2T3 Canada

(905)624-5010

www.panasonic.ca

For Europe and other countries:

Panasonic Corporation

http://www.panasonic.com

Panasonic Corporation

Osaka, Japan

Authorised Representative in EU:

Panasonic Testing Centre

Panasonic Marketing Europe GmbH

Winsbergring 15, 22525 Hamburg, Germany

ﬂes0717-0 PGQX2186ZA Printed in China

*4 The power cord plug is attached to the camera.

The following parts are used during installation procedures.

Camera mount bracket 1 pc. .......................................

Camera fixing screw (M3) 2 pcs. (incl. 1 spare) ...................................

Decorative cover (upper part and lower part) 1 pc. ......

Power cable plug*4 ............................................. 1 pc.

Installation

The installation tasks are explained using 4 steps.

Examples of when using the mount brackets (optional accessory) to install the camera

Preparations

Detach the camera

Step 2

Making connections

Step 1

Fix the mount bracket

and hang the camera

⇨⇨

Step 4

Configure the network

settings

⇨

Step 3

Fixing the camera

Other items that are needed (not included)

Preparations before installation

Prepare the required parts for each installation method before starting the installation. The following

are the requirements for the various installation methods.

Installation method

Mounting

screw

Minimum pull-

out strength*1

Ⓐ Installing the camera to a ceiling that has adequate

structural strength

Use the camera mount bracket (accessory).

M4 screws/

4pcs.

196 N {44 lbf}

Ⓑ Installing the camera to a ceiling that has inadequate

structural strength

The area of the ceiling that the camera will be installed to

must be sufﬁciently reinforced, or the optional ceiling mount

bracket for the camera (WV-Q105A*2, weight approx. 150 g

{0.33 lbs}) must be used.

M10 anchor

bolts/2pcs.

5 times or more of

the total weight in-

cluding the camera

inadequate structural strength

The area of the ceiling that the camera will be installed

to must be sufﬁciently reinforced, or the optional ceiling

embedding bracket for the camera (WV-Q126A*

2, weight

approx. 1.3 k {2.87 lbs}) must be used.g

M10 anchor

bolts/2pcs.

5 times or more of

the total weight in-

cluding the camera

ⒹInstalling the camera to a wall

Use the wall mount bracket (WV-Q119*2, weight approx.

650 {1.43 lbs}).g

M4 screws/

4pcs.

196 N {44 lbf}

*1 The minimum pull-out strength is the value per screw.

*2 For details on procedure for attaching mount bracket and camera, read the operating instruc-

tions of each mount bracket.

【1】Insert an SD memory card (locally

procured) as occasion demands.

* SDXC/SDHC/SD memory card is described as

SD memory card.

Insert an SD memory card following the procedure

shown below. For the detailed procedure, refer to

Important Information on the provided CD-ROM.

①Slide the SD memory card cover to the arrow

direction to open the cover.

②

Insert an SD memory card fully into the SD memory

card slot, and then push the memory card straight

into the slot until a click is heard. (The label should

face the bottom side of the camera)

③Shut the SD memory card cover.

Step 1 Fix the mount bracket and hang the camera

This Installation Guide explains the above

Ⓐ “Installing the camera to a ceiling that

has adequate structural strength”. When

you use mount brackets (optional acces-

sory), read their operating instructions.

【1】

Process the installation surface.

Decide the attachment position and bore

holes for screws or anchors on the ceiling

and a hole for wiring (ø25 mm {31/32 inch-

es}) as occasion demands.

Note:

• The center point of the camera mount

bracket (accessory) should be more

than 100 mm {3-15/16 inches} away

from obstacles such as a wall.

• The camera mount bracket (accessory)

should be installed with its “⇧FRONT”

mark in the Panasonic logo direction

(shooting direction) after installation.

【2】

Attach the camera mount bracket

using 4 fixing screws (M4: locally

procured).

Minimum pull-out strength:

196 N {44 lbf} (per 1 pc.)

【4】Attach the safety wire fixed with the

camera mount bracket to the camera.

After attaching the safety wire to the camera,

confirm that the ring part at the end of the

safety wire is securely hooked on the safety

wire holder.

Note:

• The camera is not fixed temporarily. Take

care not to hit the camera against

periphery (especially the dome section).

• Retain a work space of 350 mm

{1 ft 1-25/32 inches} or more from the

ceiling when you hang the camera from

the ceiling.

Ceiling mount bracket (WV-Q105A)

Ceiling embedding bracket (WV-Q126A)

Wall mount bracket (WV-Q119)

Ⓑ Ⓒ Ⓓ

IMPORTANT:

• Prepare mounting screws (M4) and anchor bolts to be mounted on a ceiling and wall separately.

• Select screws according to the material of the location that the camera will be mounted to. In

this case, wood screws and nails should not be used.

• If the mounting location such as plaster board is too weak to support the total weight, the area

shall be sufficiently reinforced.

Bottom side

SD memory card slot SD memory

card cover

Label facing

bottom side

IMPORTANT:

• The protective caps are used to prevent dirt

and dust from entering inside this product.

Keep the protective caps inserted in connec-

tors that are not used.

Wiring hole

(ø25 mm {31/32 inches})

75 mm

{2-15/16 inches}

【3】

Remove the protective cap of each

connecting terminal if the audio

input and the audio output are used.

Keep the removed protective caps for future

use.

IMPORTANT:

• To prevent an injury and protect the cable, fin-

ish the side through hole for the cable with a

file so that it does not become sharp.

• Make sure that no cable is pinched by the

decorative cover when installing it.

【5】

Process the decorative cover (acces-

sory) as necessary.

Remove the cutout part on the decorative cover

when directly attaching the cable to a ceiling with

open wiring. Install the camera and wire through

the cutout part of the decorative cover as shown

in the illustration below when you finally fit the

decorative cover.

WV-S6131

100 mm {3-15/16 inches} or

more away from obstacles

such as wall

Camera mount

bracket

(accessory)

46 mm

{1-13/16 inches}

83.5 mm

{3-9/32 inches}

Protective caps

Front direction of the camera

Safety wire

Safety wire holder

Dome section

Camera mount bracket

(accessory)

350 mm

{1 ft 1-25/32 inches}

Decorative cover

(upper part and

lower part)

Step 2 Making connections

【1】Connect an Ethernet cable (category 5e or better, straight) to the network

connector.

【2】If needed, connect a microphone or the line out of an external device to

the audio input connector.

【3】If needed, connect a powered speaker to the audio output connector.

Note:

• The audio output can be switched to the monitor output. The default is “Audio”.



Refer to the “Operating Instructions” on the provided CD-ROM for descriptions of

how to switch the output.

• If the audio output is used for the monitor output, connect a

ø3.5 mm stereo mini connector (locally procured) to the wire as

shown in the right figure and use it.

■

Refer to the Important Information on the provided CD-ROM for details about

each cable.

●As necessary, use a cable tie (locally procured) to tie the cables together.

* Make sure to use the stereo mini plug.

Step 3 Fixing the camera

IMPORTANT:

• Turn off each system’s power supply (PoE hub or device to supply power to the camera)

before making a connection.

• The 12 V DC power supply shall be insulated from the commercial AC power.

【1】Mount the camera onto the cam-

era mount bracket (accessory)

and ﬁx it temporarily.

①Remove the protective tube (for pro-

tection during transportation) covering

the lock plate.

②Fit the lock plate of the camera onto

the guide part of the camera mount

bracket, rotate the camera clockwise

by 20 ° as seen from the bottom and

fix it temporarily after inserting the

camera while putting the center of the

camera onto the center of the camera

mount bracket.

IMPORTANT:

• When mounting the camera onto the

camera mount bracket, hold the fixed

section of the unit. Mounting the cam-

era while holding the dome section may

result in malfunction.

【2】Fix the camera on the camera

mount bracket using the camera

ﬁxing screw (M3, accessory).

Recommended tightening torque: 0.68 N·m

{0.50 lbf·ft}

* Wires connected to the camera are omitted in

the illustrations.

Status indicator 【】2 Audio input connector*

【】3 Audio output connector*

【4】12 V DC power supply terminal

【】5 EXT I/O terminals

【】1 Network connector

Approx. 20 °

Guide part

Lock plate

Center of the

camera mount

bracket

Fixing screw

(M3, accessory)

Fixed section

【3】

Match the “❘” position of the deco-

rative cover to the arrow of the

unit, and then slightly push up the

decorative cover while holding the

lower part of the decorative cover.

【】3

Arrow

“ ” position❘

Decorative

cover - lower

part (accessory)

【4】Push the decorative cover up until it

is approx. 10 mm {13/32 inches} from

the ceiling, and then turn the decora-

tive cover by approx. 16 ° in the direc-

tion of the arrow (clockwise as seen

from the bottom) of the ﬁgure below.

【5】

After completing

【4】, push up the dec-

orative cover to the ceiling until it cov-

ers all of the ﬁxed section of the unit.

【】5

【】4

(Approx. 16 °)

Approx. 10 mm

{13/32 inches}

【6】

Turn the decorative cover further an

angle of 16 ° (in the arrow direction of the

upper-right ﬁgure) clockwise as seen

from the bottom to secure the cover.

IMPORTANT:

• Make sure that no cable is pinched by the

decorative cover.

【7】Make sure that all of the end part of

the locking arm has come out from

the hole in the decorative cover.

Locking arm

【】6

(Approx. 16 °)

Lens

【8】Remove the cover ﬁlm from the lens

after the installation is completed,

and then turn on the camera.

IMPORTANT:

• Once the camera is turned on, it starts to

be initialized and panning/tilting/zoom/

focus automatically operate. Do not touch

the dome section with your hand while the

camera is rotating.

Detach the camera

【1】

Detach the decorative cover (acces-

sory) from the camera by following

Step 3 “Fixing the camera” (Left) in

the reverse order of

【3】→【7】.

①

Turn the decorative cover by approx. 16 °

in the direction of the arrow (counterclock-

wise) as illustrated while pushing down the

locking arm with a tip of the ball-point pen,

and pull it slightly down from the ceiling.

②Turn the decorative cover a further 16 °

in the direction of the arrow (counter-

clockwise) as illustrated, and then

remove the decorative cover.

IMPORTANT:

• Hold the decorative cover with both

hands when removing it.

⋈

⋇

【2】Detach the 12 V DC power cable

plug (accessory) or the Ethernet

cable from the camera (When

using PoE), and then turn off the

power of the camera.

IMPORTANT:

• Before turning off the camera power,

make sure that the SD MOUNT indicator

is turned off. If you turn off the camera

power while the SD MOUNT indicator is

lit or flashing, the recorded data may be

corrupted or damaged.

【3】Remove the ﬁxing screw (accesso-

ry) that is ﬁxing the camera on the

camera mount bracket (accessory).

Dome section

Approx. 20 °

Fixed section

【4】Rotate the ﬁxed section by approx.

20 ° counterclockwise to detach

the camera from the camera

mount bracket.

IMPORTANT:

• When detaching the camera from the

camera mount bracket, hold the fixed

section of the unit. Detaching the camera

while holding the dome section may

result in malfunction.

Note:

• Take care not to hit the camera

(especially the dome section)

against surrounding objects as the

camera is unfixed.

Note:

• Since the space around

the connector is limited,

use audio cables and an

Ethernet cable that do not

exceed the sizes described

in the illustrations.

Example of

audio cable connector

30 mm

{1-3/16 inches}

Straight section

17 mm {21/32 inches}

Straight section

30 mm {1-3/16 inches}

40 mm {1-9/16 inches}

13 mm

{1/2 inches}

9 mm

{11/32 inches}

Example of

Ethernet cable connector

ø9 mm

{11/32 inches}

【4】When connecting an AC adaptor or an external power supply, use the power

cable plug (accessory) to connect it to the camera.

①Remove 3 mm - 7 mm {1/8 inches - 9/32 inches} of

the outer jacket of the cable for the AC adaptor,

expose the wire more and twist the stripped part of

the wire sufficiently.

When connecting an external power supply to the

camera, use the 16 AWG to 24 AWG single-wired

or stranded wired cables.

②Loosen the screws of the power cable plug and

insert the wire for the AC adaptor into the plug.

③Tighten the screw of the power cable plug.

(Recommended tightening torque: 0.34 N·m

{0.25 lbf·ft})

④Install the power cable plug into the camera.

Caution:

• A READILY ACCESSIBLE DISCONNECT DEVICE SHALL BE INCORPORATED TO THE

EQUIPMENT POWERED BY 12 V DC POWER SUPPLY.

• ONLY CONNECT 12 V DC CLASS 2 POWER SUPPLY (UL 1310/CSA 223) or LIMITED

POWER SOURCE (IEC/EN/UL/CSA 60950-1).

【5】If needed, connect the alarm input/output cables to the EXT I/O terminals.

Connect the cables of external devices to the EXT I/O terminal.

① Remove 8 mm - 9 mm {5/16 inches - 11/32 inches} of the outer jacket of the cable and twist

the cable core to prevent the short circuit first. Specification of cable (wire): 20 AWG - 26

AWG, Single core, twisted

② Push down the button of the desired terminal on the external I/O terminal plug with a ballpoint

pen, and release the button when the cable of the external device is fully inserted into the ter-

minal hole.

Note:

• Do not connect 2 wires or more directly to a terminal. When it is necessary to connect 2

or more wires, use a splitter.

• Check whether the stripped part of the wire is not exposed and is securely connected.

• The default of EXT I/O terminals is “Off”. Refer to the Operating Instructions on the pro-

vided CD-ROM for further information about the EXT I/O terminal settings.

Strip range

Approx. 3 mm - 7 mm

{1/8 inches - 9/32 inches}

−+

(+) white/black cord

(12 V DC)

Power cable

plug (accessory)

■

The

status

indicator will light or blink as follows depending on

the camera status.

(Refer to the illustration of Step 2 Making connections)

Operation status Indicator status

When the power is

turned on

Before the network con-

nection is established

Lights orange Lights off → →

Blinks orange Lights orange→

When the network con-

nection is established

Lights orange Lights off Blinks → →

orange Blinks green Lights green→ →

During the standby or

connection

Cable is not connected Lights orange

Cable is connected Lights green

During the upgrade process Blinks orange

Initialization (When the network connection is

established)

Lights orange Lights off Blinks → →

orange Lights orange Blinks → →

orange Blinks green Lights green→ →

Port forwarding error caused by the UPnP function Blinks orange (in 2 seconds intervals

(on for 1 second/off for 1 second))

Trouble happening on the camera Blinks red

Failure in writing data on the SD memory card Lights red

Step 4 Configure the network settings

Configure the setting of the camera after temporarily invalidating the firewall software. Once the

camera configuration is completed, return to the original state.

Contact the network administrator or your Internet service provider for information about configuring

the settings of the network.

【1】Insert the provided CD-ROM into the CD-ROM drive of your PC.

• The License Agreement will be displayed. Read the Agreement and choose “I accept the term in

the license agreement”, and click [OK].

⇒ The launcher window will be displayed.

Note:

• If the launcher window is not displayed,

double click the “CDLauncher.exe” file

on the CD-ROM.

• Refer to “Using the CD-ROM” in the

Operating Instructions on the provided

CD-ROM for further information about

CDLauncher.

【2】Click the [Run] button next to [IP Setting Software].

⇒



[Panasonic IP Setting Software] screen will be displayed.

The MAC Address / IP address of the detected camera will be displayed.

【3】Select the camera you want to configure (

➀), and click [Network Settings] (➁)

to change the network settings. Then, click [Access Camera] (

➂).

Note:

• Select the camera with same MAC address as the MAC address printed on the camera that

you want to configure.

➀

➂

【4】When the administrator registration window is displayed, enter “User

name”, “Password” and “Retype password” by following the instructions

displayed on the screen, and then click the [Set] button.

Please keep your user name and password in a safe place free from public view to ensure

security.

After completing the registration, the camera will automatically be re-connected and the

authentication window will be displayed. Enter the registered user name and password.

The default setting of

user authentication

is “On”. For further

information, refer to

the “Preface” sec-

tion in the Operating

Instructions.

IMPORTANT:

• When the camera is used over the Internet, setting user authentication to “Off” may lead

to unintended access by a third party. Please leave user authentication set to “On”.

【5】When live images from the camera are displayed, the network connection

is complete.

Note:

For more information on the following content, refer to the Operating Instructions.

•

Please set [Time & date] on the [Basic] screen of “Setup” before using the camera.

• It is impossible to display H.265 (or H.264) or MJPEG images, receive/transmit audio,

display logs, and use full-screen display when the viewer software “Network Camera

View 4S” is not installed on the PC. Push the [Viewer Software] button on the live screen

to install the software as necessary.

• Depending on the environment of your PC, it may take time for images to be displayed.

• At the time of purchase, [Audio transmission mode] is set to “Off”.If needed, change the

setting on the [Audio] tab on the “Image/Audio” page in “Setup”.

• Due to security enhancements in “IP Setting Software”, “Network settings” cannot be

changed when around 20 minutes have passed after turning on the power of the camera

to be configured. (When the effective period is set to “20 min” in the “Easy IP Setup

accommodate period”.) However, settings can be changed after 20 minutes for cameras

in the initial set mode.

If images are not displayed, set the Web browser to compatibility view. For details on how to

configure, refer to our website (http://security.panasonic.com/support/info/)

➁

(–) black cord

(GND)

External I/O terminal

4321

GND

ALARM IN3 (Terminal 3)

(Alarm input / AUX output)

ALARM IN2 (Terminal 2)

(Alarm input / Alarm output)

ALARM IN1 (Terminal 1)

(Alarm input / Black & white input / Auto time adjustment input)

Button

■Install the decorative cover by the following 2 steps,

【3】

【4】

【5】

and

【6】

【7】

■Motion of the decorative cover

(accessory) when it is ﬁtted.

When attaching the decorative cover to

the camera, 3 tabs on the inside of the

decorative cover are passed through the

(3) guides on the side of the camera and

fixed.

【5】Disconnect the remaining connected cables from the camera.

【6】Detach the safety wire from the camera and take off the camera from the

installation surface.

Camera mount

bracket (accessory)

GNDVideo output

Video output

Dome section

Guide part on the

camera side

Tab on the inside of the

decorative cover

Enlarged view of the guide part

【6】【6】

【5】

【4】【3】

Product specificaties

Merk:	Panasonic
Categorie:	Bewakingscamera
Model:	WV-S6131
Kleur van het product:	Black, White
Gewicht:	1740 g
Hoogte:	214 mm
Soort:	IP-beveiligingscamera
Materiaal behuizing:	Acrylonitrielbutadieenstyreen (ABS)
Ondersteunde mobiele besturingssystemen:	Android, iOS
Bluetooth:	Nee
Maximale capaciteit van de geheugenkaart:	256 GB
Ondersteund audioformaat:	AAC-LC, G.711, G.726
Vormfactor:	Torentje
Ondersteuning voor plaatsing:	Binnen
Ethernet LAN:	Ja
Montagewijze:	Plafond
Maximum resolutie:	1920 x 1080 Pixels
Totaal aantal megapixels:	3 MP
Videocompressieformaten:	H.264, H.265
Diameter:	185 mm
Type stroombron:	DC, PoE
Minimale belichting:	0.0004 Lux
Aantal cameras:	1
Geïntegreerde geheugenkaartlezer:	Ja
Compatibele geheugenkaarten:	SD, SDHC, SDXC
Ingebouwde HDD:	Nee
Zoomcapaciteit:	Ja
Microfoon, line-in ingang:	Ja
Aantal Ethernet LAN (RJ-45)-poorten:	1
Brandpuntbereik:	4.25 - 170 mm
Hoofdtelefoonuitgangen:	1
Volledige HD:	Ja
Omvang optische sensor:	1/2.8 "
Type beeldsensor:	MOS
Digitale zoom:	16 x
Optische zoom:	60 x
Netwerkstandaard:	IEEE 802.3af
Aantal gebruikers:	14 gebruiker(s)
Maximaal 30 frames per seconde:	60 fps
Power over Ethernet (PoE):	Ja
PTZ control:	Ja
Pan bereik:	0 - 360 °
Minimum aperture number:	1.6
Achtergrondverlichting compensatie:	Ja
Stroomverbruik (voeding via Ethernet (PoE)):	12 W
Wide Dynamic Range (WDR):	Ja
Wifi:	Nee
Bedrijfstemperatuur (T-T):	-10 - 50 °C
Relatieve vochtigheid in bedrijf (V-V):	10 - 90 procent
Bereik kantelhoek:	-25 - 205 °
Kijkhoek lens, horizontaal:	66 °
Kijkhoek lens, verticaal:	39 °
Dynamisch bereik:	144 dB