Panasonic DP-101ZL3-M-P-C Handleiding

Panasonic Niet gecategoriseerd DP-101ZL3-M-P-C

Lees hieronder de 📖 handleiding in het Nederlandse voor Panasonic DP-101ZL3-M-P-C (9 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 45 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/9

MEUML-DP100 V1.1

Thank you for purchasing products from Panasonic Electric Works SUNX

Co., Ltd. Please read this Instruction Manual carefully and thoroughly for

the correct and optimum use of this product. Kindly keep this manual in a

convenient place for quick reference.

This product has been developed / produced for industrial use only.

Use within the rated pressure range.

Do not apply pressure exceeding the pressure resistance value. The

diaphragm will be damaged resulting in faulty operation.

Make sure that the power supply is o while wiring.

Incorrect wiring will damage the sensor.

Verify that the supply voltage including the ripple is within the rating.

If power is supplied from a commercial switching regulator, ensure that

the frame ground (F.G.) terminal of the power supply is connected to an

actual ground.

In case noise generating equipment (switching regulator, inverter motor,

etc.) is used in the vicinity of this sensor, connect the frame ground (F.G.)

terminal of the equipment to an actual ground.

Do not use during the initial transient time (0.5s) after the power supply is

switched on.

Do not run the wires together with high-voltage lines or power lines or put

them in the same raceway. This can cause malfunction due to induction.

The specication may not be satised in a strong magnetic eld.

Avoid dust, dirt, and steam.

Take care that the sensor does not come in direct contact with water, oil,

grease, or organic solvents such as thinners, etc.

Do not insert wires, etc., into the pressure port. The diaphragm will be

damaged resulting in faulty operation.

Do not operate the keys with pointed or sharp objects.

Do not apply stress directly to the sensor cable joint by forcibly bending

or pulling.

Use a 12mm end wrench (14mm for DP-100-E type) when tightening a

commercial coupler to the pressure port. The tightening torque should be

9.8N·m or less (M5 female connector: 1N·m or less). The commercial

coupler or pressure port section will be damaged if the tightening torque is

excessive.

Wrap sealing tape around the coupler when connecting to prevent leaks.

INSTRUCTION MANUAL

WARNING

• Never use this product as a sensing device for personnel protection.

• In case of using sensing devices for personnel protection, use

products which meet laws and standards, such as OSHA, ANSI or

IEC etc., for personnel protection applicable in each region or

country.

• DP-100 series is designed for use with non-corrosive gas. It cannot

be used for liquid or corrosive gas.

• Japanese Measurement Laws prohibit the use of this product in

Japan.

1CAUTIONS

2PART NAMES

No. Part Description

1Output 1 opera-

tion indicator

Lights up when comparative output 1 is

2Output 2 / analog

voltage operation

indicator

•Standard type: lights up when

comparative output 2 is ON

•Multifunction type: lights up when

analog voltage output is ON

3Pressure unit dis-

play

Depending on the model, “MPa” or “kPa”

appears here. If you set another pressure

unit, attach the appropriate label, e.g. psi,

bar, etc.

4Main display Large 4-character LCD display.

5Sub-display Small 4-character LCD display.

6Mode selection

key

For details, see page 3, section 8,

SELECTING MODES.

7Up key Increases value being set.

8Down key Decreases value being set.

94-pin male con-

nector

See “Pin assignment, 4-pin male connec-

tor” on page 2.

0Pressure port • DP-100 type: R1/8 + M5 female screw

• DP-100-E type: G1/8 + M5 female

screw

• DP-100-M type: M5 female screw

• DP-100-N type: NPT1/8 + M5 female

screw

3PIPING

㧝

DP-100

876

12mm end wrench

Pressure Sensor

For use outside Japan

High-performance Digital Display

DP-100 Series

The sensor mounting bracket (MS-DP1-1) is available as an option.

When mounting the sensor onto the sensor mounting bracket, etc., the

tightening torque should be 0.5N·m or less.

The panel mounting bracket MS-DP1-2 (optional) and MS-DP1-4

(optional), as well as the front cover MS-DP1-3 (optional) and DPX-04

(optional) are also available.

The type of the front cover diers depending on the mounting bracket.

Use MS-DP1-3 for MS-DP1-2, and DPX-04 for MS-DP1-4.

To mount the panel mounting bracket, refer to the Instruction Manual

enclosed with MS-DP1-2 or MS-DP1-4.

Connection method

Attach the female connector of cable

CN-14A- to the 4-pin male connector.

Disconnection method

While pressing the release lever, pull out

the connector.

Pin assignment, 4-pin male connector

Notes:

When using the analog voltage output, pay careful attention to the

connected device’s input impedance.

If the cable is extended, the cable resistance will cause the voltage to

drop.

NPN output type

Standard type

Multifunction type

PNP output type

Standard type

Multifunction type

The EASY mode, hysteresis mode or window comparator mode can be

selected as the output mode for comparative output 1 and, for the standard

type DP-100, comparative output 2.

For details, see page 5, section 10, MENU SETTING MODE.

Easy mode

The comparative output is turned ON or OFF (depending on the N.O./N.C.

setting) when the threshold is reached. The tolerance of the threshold is

specied by the hysteresis setting. For details, see page 6, section 11, PRO

MODE.

4MOUNTING

No. Part Description

1M3 (length 6mm) screws

with washers

Accessory with MS-DP1-1

2Sensor mounting bracket

(MS-DP1-1)

Optional

5WIRING

Pin no. Terminal name

1+V

2Comparative output 1

3• Standard type: Comparative

output 2

• Multifunction type: Analog

voltage output or external input

40V

6I/O CIRCUIT DIAGRAMS

CN-14A-Cغ

Contact: SPHD-001T-P0.5

Housing: PAP-04V-S

[JST Mfg. Co., Ltd.]

Release lever

e w

ith

ema

connector

Ԙ ԙ Ԛ ԛ

㧝

7OUTPUT MODE AND OUTPUT OPERATION

Notes: • Hysteresis can be xed in 8 levels.

For details, see page 6, section 11, PRO MODE.

•P-1 is displayed for comparative output 1 and P-2 for

comparative output 2 on the sub-display.

User’s circuitInternal circuit

12 to 24V DC

±10%

(Black)

Comparative output 1

Main circuit

(White) Comparative output 2

(Blue) 0V

100mA max.

Load

(Brown) +V

Color code of cable with connector

_±10%

1kǡ

Main circuit

Users' circuitInternal circuit

(Black) Comparative output 1

(Blue) 0V

100mA max.

Load

(Brown) +V

Color code of cable with connector

12 to 24V DC

(White)

Analog voltage output

or external input

_±10%

100mA max.

Main circuit

User’s circuitInternal circuit

(Black) Comparative output 1

(White) Comparative output 2

(Blue) 0V

100mA max.

Load

(Brown) +V

Color code of cable with connector

12 to 24V DC

_±10%

1kǡ12 to 24V D

Main circuit

(Black) Comparative output 1

User’s circuitInternal circuit

(Blue) 0V

100mA max.

Load

(Brown) +V

Color code of cable with connector

(White)

Analog voltage output

or external input

H (Hysteresis)

OFF

Pressure

Comparative

output

Hysteresis mode

The comparative output is turned ON or OFF (depending on the N.O./N.C.

setting) when the upper or lower threshold is reached and remains ON or

OFF until the other threshold is reached.

Window comparator mode

The comparative output is turned ON or OFF (depending on the N.O./N.C.

setting) when the pressure lies between the upper or lower threshold. The

tolerance of the threshold is specified by the hysteresis setting. For details,

see page 6, section 11, PRO MODE.

DP-100 has 3 dierent modes:

RUN mode. For details, see page 3, section 9, RUN MODE.

Menu setting mode. For details, see page 5, section 10, MENU

SETTING MODE.

Pro mode. For details, see page 6, section 11, PRO MODE.

Switching modes

Press to switch between modes.

From RUN mode, press for 2s to select the menu setting mode.

From RUN mode, press for 4s to select pro mode.

To return to RUN mode, press for 2s.

In RUN mode, you can lock the keys and adjust the threshold for the param-

eters set in menu setting mode while the sensor is operating. For details,

see page 5, section 10, MENU SETTING MODE.

Threshold settings are displayed in the sub-display.

If you attempt to set threshold values that exceed the pressure range

allowed, DP-100 will alert you. UP (exceeds the upper limit) or DOWN (exceeds

the lower limit) will appear on the sub-display. DOWN will also appear if the Hi

threshold value exceeds the Lo threshold value for the hysteresis mode or

window comparator mode.

Standard type

Notes: • H (Hysteresis): 1 digit or more, 2 digits or more when psi is

selected as the pressure unit.

•Hi-1 or Lo-1 is displayed for comparative output 1 and Hi-2 or Lo-

2 for comparative output 2 on the sub-display.

Notes: • Hysteresis can be xed in 8 levels.

For details, see page 6, section 11, PRO MODE.

•Hi-1 or Lo-1 is displayed for comparative output 1 and Hi-2 or Lo-

2 for comparative output 2 on the sub-display.

8SELECTING MODES

9RUN MODE

Setting condition 1

Comparative output 1 set to: (EASY mode)EASY

Comparative output 2 set to: (OFF)OFF

OFF

H (Hysteresis)

Pressure

Comparative

output

H (Hysteresis)

Pressure

OFF

Comparative

output

MODE

Setting condition 2

Comparative output 1 set to: (EASY mode)EASY

Comparative output 2 set to: (EASY mode)EASY

Setting condition 3

Comparative output 1 set to: (EASY mode)EASY

Comparative output 2 set to: (Hysteresis mode), orHYS

WCMP (Window comparator mode)

Setting condition 4

Comparative output 1 set to: (Hysteresis mode), orHYS

WCMP (Window comparator mode)

Comparative output 2 set to: (OFF)OFF

Setting condition 5

Comparative output 1 set to: (Hysteresis mode), orHYS

WCMP (Window comparator mode)

Comparative output 2 set to: (EASY mode)EASY

Setting condition 6

Comparative output 1 set to: (Hysteresis mode), orHYS

WCMP (Window comparator mode)

Comparative output 2 set to: (Hysteresis mode), orHYS

WCMP (Window comparator mode)

MODE

Automatic

MODE

Automatic

MODE

Automatic

MODE

Automatic

MODE

Automatic

Product specificaties

Merk:	Panasonic
Categorie:	Niet gecategoriseerd
Model:	DP-101ZL3-M-P-C

Heb je hulp nodig?

Als je hulp nodig hebt met Panasonic DP-101ZL3-M-P-C stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Panasonic

Panasonic DMW-YAGH Handleiding

11 December 2024

Panasonic ET-EMT750 Handleiding

7 December 2024

Panasonic ET-DLE020 Handleiding

7 December 2024

Panasonic ET-C1W400 Handleiding

7 December 2024

Panasonic ET-C1W300 Handleiding

7 December 2024

Panasonic ET-EMT850 Handleiding

7 December 2024

Panasonic MultiShape ER-CKN3 Handleiding

25 November 2024

Panasonic NB-W250 Handleiding

25 November 2024

Panasonic SC-XH100 Handleiding

24 November 2024

Panasonic DMW-AVC1 Handleiding

24 November 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Voltcraft MSW 3000-12-G Handleiding

30 December 2025

Voltcraft AL6000 Handleiding

30 December 2025

Voltcraft BC2500 Handleiding

30 December 2025

Voltcraft PSW 3000-12-G Handleiding

30 December 2025

Voltcraft PSW 1500-12-G Handleiding

30 December 2025

Voltcraft PSW 2000-12-G Handleiding

30 December 2025

Einhell WB 50 Handleiding

30 December 2025

Hisense HAF1800D Handleiding

30 December 2025

Eufy Outdoor / Indoor Siren Handleiding

30 December 2025

Lenco TTA-180TN Handleiding

30 December 2025