Ozito TBS-2000 Handleiding

Ozito Zaagmachine TBS-2000

Lees hieronder de 📖 handleiding in het Nederlandse voor Ozito TBS-2000 (10 pagina's) in de categorie Zaagmachine. Deze handleiding was nuttig voor 34 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/10
ONLINE MANUAL
Scan this QR Code with
your mobile device to take
you to the online manual.
A A
R R
L L
1. Rear Table Extension
2. Rubber Feet x 4
3. Riving Knife
4. Blade Guard
5. Side Table Extensions x 2
6. Height Adjustment Handle
7. Bevel Adjustment Dial
8. Cross Struts x 4
9. Right Table Struts x 2
10. Rear Table Struts x 2
11. Left Table Struts x 2
12. Table Legs x 4
13. Stabilising Brackets
PARTS
FASTENERS
TBS-2000
14. Spanner (10/12mm)
15. Pin Spanner (10mm)
16. Spring Washers x 16
17. Large Washers x 8
18. Small Washers x 32
19. Hex Nuts x 32
20. Round Head Bolts x 16
21. Long Bolts x 8
22. Short Bolts (washers pre-
assembled) x 16
2
12 8 7 6 5 4 313 11 10 9
1
14
22 21 20 19 18 17 16 15
1. Separate the di󰀨erent nuts and bolts
into groups of same components and
check you have the correct quantities.
Note: The spring washers and washers
pre-assembled on the short bolts are not
included in the fastener list count.
2. Remove the screw from the height/
bevel rod and slide the bevel
adjustment dial onto the rod ensuring
the teeth on cogs align.
3. Slide the height adjustment handle
onto the rod by aligning the at
section and secure in place using the
screw that was previously removed.
4. Ensure the blade height is wound fully
down and then turn the table saw upside
down on the oor.
5. Remove any cardboard boxes from
behind the motor; it can be easily
accessed by tilting the blade using the
bevel adjustment dial.
6. Place a large washer onto each long
bolt. Insert the 4 table legs into the
bottom of the table saw and loosely
attach using the long bolts and large
washers from the outside of each leg.
Note: These bolts will need to be
removed later, so only attach loosely.
7. Attach the 4 cross struts by aligning
the holes on the strut and on the leg
(ensure the lip is facing the table saw).
Secure each end using 2 round head
bolt, washer, spring washer and nut
assemblies.
8. Attach the 2 stabilising brackets to the rear legs. Place a short
bolt through the bracket and table
leg, slide a washer onto the bolt and
then secure it with a hex nut. Repeat
for the other mounting point and
stabilising bracket.
9. Mount the rubber feet onto the bottom
of the legs.
1. ASSEMBLING THE FRAME
8x 16x 16x
22.5°
15°
30°
45°
WARNING! BEFORE ASSEMBLING YOUR TABLE
SAW OR REPLACING BLADES, ENSURE THAT THE
MOTOR IS OFF AND THE TOOL IS DISCONNECTED
FROM THE POWER SUPPLY TO PREVENT
ACCIDENTAL STARTING.
TABLE SAW
2000W 254mm
ASSEMBLY MANUAL
0920
TBS-2000
1. Flip the table saw upright onto its
feet, raise the blade to its highest
setting and remove the table
insert by loosening the 2 screws
holding it down.
2. Loosen the riving knife securing
bolt using the supplied spanner.
Ensure the bolt does not come
completely out as this bolt may be
di󰀩cult to ret.
3. Insert the riving knife between the
mounting plate and the securing
bolt so that there is a 3-5mm gap
between the blade and the riving
knife. Tighten the securing bolt
using the supplied spanner.
4 Ret the table insert by sliding it around the blade from the front
of the unit towards the back. Ensure the plastic tab on the table
insert is properly slotted into the groove in the table top. The table
insert should be ush with the surface of the table saw.
5. Secure with its 2 screws.
WARNING! THE BLADE GUARD MUST ALWAYS BE
LOWERED OVER THE WORK PIECE BEFORE YOU
BEGIN TO CUT.
The table saw is supplied with 1
rear table extension and 2 side table
extensions.
For ease of assembly, place the
table saw upside down on a at
surface with space for the table
extensions.
1. Align the bolt holes of the rear
extension with the back edge of
the table saw. Use the bolt holes
and front ruler edge of the table to
align the side extensions.
2. Insert a pre-assembled short bolt
through a bolt hole in the table
saw and extension table, place
a washer onto it and secure with
a hex nut. Repeat this for the
other 5 bolt holes to attach the
extensions tables.
Note: There are 3 pairs of table struts.
The shortest pair (inscribed with ‘R’)
is meant for the right extension table,
the longest (marked ‘L’) for the left
extension; the letter ‘A’ is inscribed on
the rear table struts.
3. Insert a pre-assembled short
bolt through a bolt hole on
the outer edge of the table
extension and then the bolt
hole in one end of the table
strut. Place a washer onto the
short bolt and secure it with
a hex nut. Repeat this for the
other 5 table struts.
4. To attach the table strut to the bottom
of the table saw, you will rst need
to remove the bolt and washer that
connects the leg to the table saw.
Ensure that it is supported by one
other bolt before attaching a strut.
Note: Each table leg and table strut
share the same xing hole.
5. Once all the table
struts have been
attached, tighten
all the nuts on the
base frame and table
extensions to ensure
steadiness. Use the
supplied spanners
where required, but
be careful not to over
tighten as this may
result in damage to
the base frame or the
screw threads.
3. FITTING THE BLADE GUARD2. ATTACHING TABLE EXTENSIONS
3 - 5mm
A A
LEFT
RIGHT
REAR
TABLE STRUTS
R R
L L
TABLE SAW
2000W 254mm
INSTRUCTION MANUAL
SPECIFICATIONS
Motor: 2000W (S6 40%) 1800W (S1)
Input: 230-240V ~ 50Hz
No Load Speed: 4,250/min
Blade: Ø254mm x 30 x 2.4mmØ
Blade Teeth: 24 TCT
Bevel Angle: 0 -45° leftº
Blade Height Adj: 0-80mm
Max. Cutting Capacity:
Bevel 90°: 80mm
Bevel 45°: 55mm
Table Size: 555 x 580mm
With Side Ext.: 855 x 580mm
Rear Extension: 390 x 185mm
Dust Port: Ø36mm
Weight: 26.0kg
TBS-2000
STANDARD EQUIPMENT
IN ORDER TO MAKE A CLAIM UNDER THIS
WARRANTY YOU MUST RETURN THE PRODUCT
TO YOUR NEAREST BUNNINGS WAREHOUSE WITH
YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO
RETURNING YOUR PRODUCT FOR WARRANTY
PLEASE TELEPHONE OUR CUSTOMER SERVICE
HELPLINE:
Australia 1800 069 486
New Zealand 0508 069 486
3 YEAR REPLACEMENT WARRANTY
Your product is guaranteed for a period of 36 months from
the original date of purchase. If a product is defective it will
be replaced in accordance with the terms of this warranty.
Warranty excludes consumable parts, for example: blade,push stick,
spanners, bearings & carbon brushes.
WARNING
The following actions will result in the warranty being void.
• If the tool has been operated on a supply voltage other
than that specified on the tool.
• If the tool shows signs of damage or defects caused
by or resulting from abuse, accidents or alterations.
• Failure to perform maintenance as set out within the
instruction manual.
• If the tool is disassembled or tampered with in any way.
• Professional, industrial or high frequency use.
WARRANTY
TO ENSURE A SPEEDY RESPONSE PLEASE
HAVE THE MODEL NUMBER AND DATE OF
PURCHASE AVAILABLE. A CUSTOMER SERVICE
REPRESENTATIVE WILL TAKE YOUR CALL
AND ANSWER ANY QUESTIONS YOU MAY
HAVE RELATING TO THE WARRANTY POLICY
OR PROCEDURE.
OZITO Australia/New Zealand (Head Office) 1-23 Letcon Drive, Bangholme, Victoria, Australia 3175.
The benefits provided under this warranty are in addition
to other rights and remedies which are available to you at law.
Our goods come with guarantees that cannot be excluded
at law. You are entitled to a replacement or refund for a major
failure and for compensation for any other reasonably foreseeable
loss or damage. You are also entitled to have the goods repaired
or replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure.
Generally you will be responsible for all costs associated with
a claim under this warranty, however, where you have suffered
any additional direct loss as a result of a defective product you
may be able to claim such expenses by contacting our customer
service helpline above.
ozito.com.au
0920
Base Frame Components
Push Stick, Blade Guard & Riving
Knife
Sliding Mitre
Gauge
Cutting Blades x 3
Table Extensions x 3
Assembly Fasteners
Rip Fence
A A
L L
R R

Product specificaties

Merk: Ozito
Categorie: Zaagmachine
Model: TBS-2000

Heb je hulp nodig?

Als je hulp nodig hebt met Ozito TBS-2000 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Zaagmachine Ozito

Ozito

Ozito PXCCSK-4182 Handleiding

23 Augustus 2024
Ozito

Ozito PXBPCK-1825 Handleiding

23 Augustus 2024
Ozito

Ozito PXTCSK-2520 Handleiding

23 Augustus 2024
Ozito

Ozito PXPRSS-018 Handleiding

30 Juli 2024
Ozito

Ozito PXBPCS-1815 Handleiding

30 Juli 2024
Ozito

Ozito JSW-6100U Handleiding

9 Juli 2023
Ozito

Ozito RSW-5200 Handleiding

26 Juni 2023
Ozito

Ozito JSW-4000U Handleiding

24 Juni 2023
Ozito

Ozito JSW-8100U Handleiding

20 Juni 2023
Ozito

Ozito RSW-5200U Handleiding

18 Juni 2023

Handleiding Zaagmachine

Nieuwste handleidingen voor Zaagmachine

Anova

Anova E60CS Handleiding

20 December 2024
Silverline

Silverline 447132 Handleiding

19 December 2024
Silverline

Silverline 427644 Handleiding

19 December 2024
Herkules

Herkules KS 210 Profi Handleiding

17 December 2024
Total

Total TS730301 Handleiding

16 December 2024
Total

Total TJSLI8501 Handleiding

16 December 2024
Turbo-Silent

Turbo-Silent EKS 2040/1 Handleiding

16 December 2024
Bavaria

Bavaria BJS 400 Handleiding

5 December 2024
Bavaria

Bavaria BCS 64/1 Handleiding

5 December 2024
Bavaria

Bavaria BEC 2040 TC Handleiding

5 December 2024