Ozito PXCCSS-0182 Handleiding

Ozito Zaagmachine PXCCSS-0182

Lees hieronder de 📖 handleiding in het Nederlandse voor Ozito PXCCSS-0182 (8 pagina's) in de categorie Zaagmachine. Deze handleiding was nuttig voor 54 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/8
SPECIFICATIONS
Input: 2 x 18V
Bar Length: 356mm (14”)
Max. Cutting Length: 330mm
Max. Chain Speed: 15m/s
Chain Pitch: 9.53mm (3/8”)
Chain Gauge: 1.1mm (0.043”)
Oil Tank Capacity: 225ml
Weight (Tool Only): 4.1kg
STANDARD EQUIPMENT
Brushless Chainsaw
BRUSHLESS
CHAINSAW
INSTRUCTION MANUAL
ozito.com.au
Guide Bar Cover
Guide Bar
Chain
PXCCSS-0182
IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY YOU
MUST RETURN THE PRODUCT TO YOUR NEAREST BUNNINGS
WAREHOUSE WITH YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO
RETURNING YOUR PRODUCT FOR WARRANTY PLEASE TELEPHONE
OUR CUSTOMER SERVICE HELPLINE:
Australia 1800 069 486
New Zealand 0508 069 486
WARRANTY
TO ENSURE A SPEEDY RESPONSE PLEASE HAVE THE MODEL
NUMBER AND DATE OF PURCHASE AVAILABLE. A CUSTOMER
SERVICE REPRESENTATIVE WILL TAKE YOUR CALL AND
ANSWER ANY QUESTIONS YOU MAY HAVE RELATING TO THE
WARRANTY POLICY OR PROCEDURE.
OZITO Australia/New Zealand (Head Ofce) 1-23 Letcon Drive, Bangholme, Victoria, Australia 3175.
The benets provided under this warranty are in addition to other rights and
remedies which are available to you at law.
Our goods come with guarantees that cannot be excluded at law. You are entitled to
a replacement or refund for a major failure and for compensation for any other
reasonably foreseeable loss or damage. You are also entitled to have the goods
repaired or replaced if the goods fail to be of acceptable quality and the failure
does not amount to a major failure.
Generally you will be responsible for all costs associated with a claim under this
warranty, however, where you have suffered any additional direct loss as a result of
a defective product you may be able to claim such expenses by contacting our
customer service helpline above.
0918
WARNING
The following actions will result in the warranty being
void.
• If the tool has been operated on a supply voltage other
than that specied on the tool.
• If the tool shows signs of damage or defects caused
by or resulting from abuse, accidents or alterations.
• Failure to perform maintenance as set out within the instruction manual.
• If the tool is disassembled or tampered with in any way.
• Professional, industrial or high frequency use.
5 YEAR REPLACEMENT WARRANTY
Your Product is guaranteed for a period of 60 months from the original date of
purchase and is intended for DIY (Do It Yourself) use only. If a product is defective it
will be replaced in accordance with the terms of this warranty. Lithium Ion
batteries and chargers are covered by a 36 month
warranty Warranty excludes consumable parts, for example: guide bar, chain
and included accessories.
356
mm
3/8” LP
52
14
in
14
in
356
mm
3/8” LP
52
CAUTION: ALWAYS WEAR GLOVES WHEN
HANDLING THE CHAIN AS IT IS VERY SHARP AND
CAN CUT YOU WHEN IT IS NOT MOVING.
WARNING! ENSURE THE TOOL IS SWITCHED OFF
AND BATTERIES ARE DISCONNECTED BEFORE
PERFORMING ANY OF THE FOLLOWING TASKS.
14
in
356
mm
3/8” LP
52
KNOW YOUR PRODUCT SETUP & PREPARATION
1. ASSEMBLY
1. Rear Handle
2. Trigger Switch
3. Battery Seating
4. Front Handle
5. Guide Bar Lock Knob
6. Chain Brake
7. Chain Oil Tank Cap
8. Guide Bar
9. Chain
10. Bucking Spikes
11. Oil Level Window
12. Side Cover
13. Chain Tension Adjustment Dial
14. Motor Cover
15. Lock-Off Button
BRUSHLESS CHAINSAW
1 2 3 4 5 6 7 8
BATTERY & CHARGER
This tool is compatible with all battery and chargers from the Ozito
Power X Change Range.
ONLINE MANUAL
Scan this QR Code with your
mobile device to take you to the
online manual.
ACCESSORIES
16. Guide Bar Cover
15
16
10 11 12 13 14
9
14
in
356
mm
3/8” LP
52
AB
14
in
356
mm
3/8” LP
52
Fitting the chain and bar
1. Completely unscrew the guide bar
lock knob, in a counter clockwise
direction.
2. Remove the side cover
3. Fit the chain over the guide bar,
making sure that the cutters are
facing in the direction of rotation.
IMPORTANT: IF THE CHAIN IS INSTALLED BACKWARDS
(CHAIN CUTTERS ARE FACING IN THE OPPOSITE
DIRECTION OF ROTATION) THE CHAINSAW WILL VIBRATE
EXCESSIVELY AND NOT CUT.
14
in
356
mm
3/8” LP
52
4. Place the guide bar and
chain in position, ensuring
that the chain is around
sprocket wheel (A). Also
ensure that the threaded
pin (B) ts into the guide
bar tension dial.
If it does not t, it
can be adjusted
slightly by turning
the dial.
5. Attach the side cover and secure it with the
side cover lock. Do not fully tighten the guide
bar lock knob until after adjusting the chain
tension.
CAUTION: IF YOU TRY TO ROTATE THE CHAIN TENSIONING
ADJUSTMENT DIAL WHILST THE CHAIN COVER LOCK IS
TIGHT, IT WILL RESULT IN THE CHAIN NOT LOOSENING
AND POSSIBLE DAMAGE TO THE MECHANISM.
2. OIL
3/8” LP
52
Note: Chain bar oil may leak if the tool is left for long periods. This is
normal. If the tool is to be left unused for an extended time, drain
the oil from the tool. Rell before use.
5. To check the lubricating system,
switch on the chainsaw and hold
it with the guide bar and chain
above some light coloured paper
such as newspaper. A steadily
increasing stain caused by oil
spray shows the lubricating
system is working.
2. Fill the tank with chain bar oil.
The capacity of the chain oil
tank is 225ml. Do not over ll.
4. Always ll the oil tank when the
oil level is below the minimum
mark on the oil level window.
WARNING!: NEVER START WORK UNLESS THE
CHAIN AND BAR ARE LUBRICATED
1. Remove the chain bar oil cap.
3. Ret cap and clean any oil
spillage.
IMPORTANT: ONLY USE OIL THAT IS EXPRESSLY LABELLED
“CHAIN BAR OIL”.
356
mm
3/8” LP
52
14
in
Adjusting the chain tension
1. Loosen the guide bar lock knob
slightly, by rotating it in an anti
clockwise direction.
2. Adjust the chain tension with
the chain tensioning adjustment
dial. Turning the dial CLOCKWISE
increases the chain tension,
turning it COUNTER-CLOCKWISE
decreases the chain tension.
For the correct chain tension,
rmly pull up on the chain at
the middle of the top of the
exposed guide bar. When
the chain is pulled up to its
highest point, the bottom tip
of the links should only just
stay in the track [middle of the
guide bar]
3. After the chain has been accurately
tensioned, lock the guide bar in
place with the guide bar lock knob.
IMPORTANT: IT IS VITAL FOR THE PROPER AND SAFE
OPERATION OF THE CHAINSAW THAT THE CHAIN IS
TENSIONED CORRECTLY.

Product specificaties

Merk: Ozito
Categorie: Zaagmachine
Model: PXCCSS-0182

Heb je hulp nodig?

Als je hulp nodig hebt met Ozito PXCCSS-0182 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Zaagmachine Ozito

Ozito

Ozito PXCCSK-4182 Handleiding

23 Augustus 2024
Ozito

Ozito PXBPCK-1825 Handleiding

23 Augustus 2024
Ozito

Ozito PXTCSK-2520 Handleiding

23 Augustus 2024
Ozito

Ozito PXPRSS-018 Handleiding

30 Juli 2024
Ozito

Ozito PXBPCS-1815 Handleiding

30 Juli 2024
Ozito

Ozito JSW-6100U Handleiding

9 Juli 2023
Ozito

Ozito RSW-5200 Handleiding

26 Juni 2023
Ozito

Ozito JSW-4000U Handleiding

24 Juni 2023
Ozito

Ozito JSW-8100U Handleiding

20 Juni 2023
Ozito

Ozito RSW-5200U Handleiding

18 Juni 2023

Handleiding Zaagmachine

Nieuwste handleidingen voor Zaagmachine

Anova

Anova E60CS Handleiding

20 December 2024
Silverline

Silverline 447132 Handleiding

19 December 2024
Silverline

Silverline 427644 Handleiding

19 December 2024
Herkules

Herkules KS 210 Profi Handleiding

17 December 2024
Total

Total TS730301 Handleiding

16 December 2024
Total

Total TJSLI8501 Handleiding

16 December 2024
Turbo-Silent

Turbo-Silent EKS 2040/1 Handleiding

16 December 2024
Bavaria

Bavaria BJS 400 Handleiding

5 December 2024
Bavaria

Bavaria BCS 64/1 Handleiding

5 December 2024
Bavaria

Bavaria BEC 2040 TC Handleiding

5 December 2024