Ozito PXCBLK-218 Handleiding
Ozito
Bladblazers
PXCBLK-218
Lees hieronder de 📖 handleiding in het Nederlandse voor Ozito PXCBLK-218 (6 pagina's) in de categorie Bladblazers. Deze handleiding was nuttig voor 38 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/6
CORDLESS
BLOWER KIT
INSTRUCTION MANUAL
SPECIFICATIONS
Voltage: 18V
Battery: 2.0Ah Li-ion
Charge Time: 2.5Hrs
No Load Speed: 12,000/min
Max. Air Speed: 210km/hr
Weight: 1.75kg
PXCBLK-218
WHAT’S IN THE BOX
Cordless Blower
2.0Ah Battery & Eco Charger
IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY YOU MUST
RETURN THE PRODUCT TO YOUR NEAREST BUNNINGS WAREHOUSE
WITH YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO RETURNING
YOUR PRODUCT FOR WARRANTY PLEASE TELEPHONE OUR CUSTOMER
SERVICE HELPLINE:
Australia 1800 069 486
New Zealand 0508 069 486
WARRANTY
TO ENSURE A SPEEDY RESPONSE PLEASE HAVE THE MODEL
NUMBER AND DATE OF PURCHASE AVAILABLE. A CUSTOMER
SERVICE REPRESENTATIVE WILL TAKE YOUR CALL
AND ANSWER ANY QUESTIONS YOU MAY
HAVE RELATING TO THE WARRANTY POLICY
OR PROCEDURE.
The benets provided under this warranty are in addition
OZITO Australia/New Zealand (Head Ofce) 1-23 Letcon Drive, Bangholme, Victoria, Australia 3175.
to other rights and remedies which are available to you at law.
Our goods come with guarantees that cannot be excluded
at law. You are entitled to a replacement or refund for a major failure and for
compensation for any other reasonably foreseeable loss or damage. You are also
entitled to have the goods repaired
or replaced if the goods fail to be of acceptable quality and the failure does not
amount to a major failure.
Generally you will be responsible for all costs associated with
a claim under this warranty, however, where you have suffered
any additional direct loss as a result of a defective product you
may be able to claim such expenses by contacting our customer service helpline
above.
ozito.com.au
0316
WARNING
The following actions will result in the warranty being
void.
• If the tool has been operated on a supply voltage other
than that specied on the tool.
• If the tool shows signs of damage or defects caused
by or resulting from abuse, accidents or alterations.
• Failure to perform maintenance as set out within the instruction manual.
• If the tool is disassembled or tampered with in any way.
5 YEAR REPLACEMENT WARRANTY
Your Product is guaranteed for a period of 60 months from the original date of
purchase and is intended for DIY (Do It Yourself) use only. If a product is defective it
will be replaced in accordance with the terms of this warranty. Lithium Ion
batteries and chargers are covered by a 36 month
warranty. Warranty excludes consumable parts, for example: blower tube.
Blower Tube
ONLINE MANUAL
Scan this QR Code with your mobile
device to take you to the online
manual.
6. Battery Release Tab
7. Battery Charge LED’s
8. Battery Charge Indicator Button
9. Charger LED’s
10. Charger LED’s
ACCESSORIES
CORDLESS BLOWER
KNOW YOUR PRODUCT
1
6
2
7
3
8
4
9
5
10
1. ASSEMBLY
SETUP & PREPARATION
1. Align the blower tube with the
outlet of the blower.
3. To remove the blower tube, press
the blower tube release tab
while pulling the tube away from
the housing.
2. Push the blower tube
onto the blower until it
clicks into place.
Fitting the Blower Tube
WARNING! ENSURE THE TOOL IS SWITCHED
OFF AND BATTERY DISCONNECTED BEFORE
PERFORMING ANY OF THE FOLLOWING TASKS.
1. Blow Tube
2. Blow Tube Release Tab
3. Handle
4. Trigger Switch
5. Battery Seating
2. BATTERY & CHARGING
Charging your lithium ion battery - Eco Charger
The tools battery has been shipped in a low charge condition, and requires
charging prior to use. Allow several cycles of charging and discharging
(through use of the tool) for the battery to reach its optimum performance /
runtime.
CAUTION: THE CHARGER FOR THIS PRODUCT
SHOULD BE PROTECTED BY A RESIDUAL CURRENT
DEVICE (RATED AT 30MA OR LESS).
Battery Charge Indicator
The purchased battery is equipped with
a battery charge indicator to show the
state of the battery charge.
Press the charge indicator button and
look to see which LED lights.
Battery requires immediate charging
Low state of charge, requires charging soon.
Mid state of charge
Full state of charge.
Note: The battery needs to be removed from the tool to check the state of
charge.
Battery protection system
The tool is equipped with the battery protection system, which helps to ensure
a long service life.
The output power automatically cuts off during operation when the tool and/
or battery are placed under the following situations:
• When the tool is overloaded:
If this occurs, release the trigger switch and remove causes of overload,
then pull the switch trigger again to restart.
• When the remaining battery capacity becomes low:
Recharge the battery pack.
Note: The battery protection system does not in any way damage the tool.
Note: The indicated capacity may be lower than the actual level during use
or immediately after using the tool.
1. Connect the charger into a mains power outlet.
4. The charger LED will illuminate red signifying that the battery is
charging.
3. With the battery sitting on a at
surface, align the raised ribs on the
battery with the recess in the charger
and slide onto the battery ensuring a
rm connection.
2. The charger LED will ash green
showing power is being supplied
to the charger.
5. When removing the charger from the
battery, rst press the battery release
tab, then slide the charger from its
position.
Charger LED Indicator
LED Indicator Situation
GREEN (Flashing) Stand By (no battery pack is inserted)
RED (Illuminated) Battery is charging (low charge)
GREEN (Illuminated) Battery is fully charged
RED (Flashing) Battery or Charger fault
RED & GREEN (Flashing) Battery pack is too hot or too cold (remove battery from
charger and store at room temperature 20ºC. Insert
battery again when at correct charging temperature). If
this happens again, the battery is defective and needs
to be replaced.
Note: The battery will not develop a memory, it does not have to be fully
discharged before recharging.
CAUTION! IF THE BATTERY IS TOO HOT OR TOO
COLD WHEN INSERTED INTO THE CHARGER,
THE LED WILL FLASH RED AND GREEN. REMOVE
BATTERY FROM CHARGER AND STORE AT ROOM
TEMPERATURE 20 C BEFORE CHARGING.º
Product specificaties
| Merk: | Ozito |
| Categorie: | Bladblazers |
| Model: | PXCBLK-218 |
Heb je hulp nodig?
Als je hulp nodig hebt met Ozito PXCBLK-218 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Bladblazers Ozito
4 Oktober 2022
4 Oktober 2022
4 Oktober 2022
Handleiding Bladblazers
- Bladblazers Bosch
- Bladblazers Dolmar
- Bladblazers Eurom
- Bladblazers Ferm
- Bladblazers Florabest
- Bladblazers Grizzly
- Bladblazers Hikoki
- Bladblazers Hitachi
- Bladblazers Hyundai
- Bladblazers Makita
- Bladblazers Metabo
- Bladblazers Shindaiwa
- Bladblazers Skil
- Bladblazers Stihl
- Bladblazers Vonroc
- Bladblazers Worx
- Bladblazers Black And Decker
- Bladblazers Ronix
- Bladblazers Meec Tools
- Bladblazers Yard Force
- Bladblazers Cramer
- Bladblazers Poulan
Nieuwste handleidingen voor Bladblazers
4 Oktober 2022
4 Oktober 2022
4 Oktober 2022
4 Oktober 2022
4 Oktober 2022
4 Oktober 2022
4 Oktober 2022
4 Oktober 2022
4 Oktober 2022
4 Oktober 2022