Ozito PXAGS-500 Handleiding
Ozito
Haakse slijpmachines
PXAGS-500
Lees hieronder de 📖 handleiding in het Nederlandse voor Ozito PXAGS-500 (6 pagina's) in de categorie Haakse slijpmachines. Deze handleiding was nuttig voor 37 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/6
SPECIFICATIONS
Voltage: 18V
Rated Speed: 8,500/min
Disc Diameter: 115mm (41/2”)
Spindle: M14
Weight: 1.8kg
115MM
ANGLE GRINDER
INSTRUCTION MANUAL
ozito.com.au
PXAGS-500
STANDARD EQUIPMENT
Angle Grinder
Side Handle
Safety Guard
Pin Wrench
Grinding Disc
IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY YOU
MUST RETURN THE PRODUCT TO YOUR NEAREST BUNNINGS
WAREHOUSE WITH YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO
RETURNING YOUR PRODUCT FOR WARRANTY PLEASE TELEPHONE
OUR CUSTOMER SERVICE HELPLINE:
Australia 1800 069 486
New Zealand 0508 069 486
WARRANTY
TO ENSURE A SPEEDY RESPONSE PLEASE HAVE THE MODEL
NUMBER AND DATE OF PURCHASE AVAILABLE. A CUSTOMER
SERVICE REPRESENTATIVE WILL TAKE YOUR CALL AND
ANSWER ANY QUESTIONS YOU MAY HAVE RELATING TO THE
WARRANTY POLICY OR PROCEDURE.
OZITO Australia/New Zealand (Head Ofce) 1-23 Letcon Drive, Bangholme, Victoria, Australia 3175.
The benets provided under this warranty are in addition to other rights and
remedies which are available to you at law.
Our goods come with guarantees that cannot be excluded at law. You are entitled to
a replacement or refund for a major failure and for compensation for any other
reasonably foreseeable loss or damage. You are also entitled to have the goods
repaired or replaced if the goods fail to be of acceptable quality and the failure
does not amount to a major failure.
Generally you will be responsible for all costs associated with a claim under this
warranty, however, where you have suffered any additional direct loss as a result of
a defective product you may be able to claim such expenses by contacting our
customer service helpline above.
0219
WARNING
The following actions will result in the warranty being
void.
• If the tool has been operated on a supply voltage other than that specied
on the tool.
• If the tool shows signs of damage or defects caused by or resulting from
abuse, accidents or alterations.
• Failure to perform maintenance as set out within the instruction manual.
• If the tool is disassembled or tampered with in any way.
5 YEAR REPLACEMENT WARRANTY
Your Product is guaranteed for a period of 60 months from the original date of
purchase and is intended for DIY (Do It Yourself) use only. If a product is defective it
will be replaced in accordance with the terms of this warranty. Lithium Ion
batteries and chargers are covered by a 36 month
warranty and are excluded from the warranty extension. Warranty excludes
consumable parts.
KNOW YOUR PRODUCT SETUP & PREPARATION
1. ASSEMBLY
CORDLESS ANGLE GRINDER
1 2 3 4 5 6
1 Spindle Lock
2 Guard Locking Screw
3 Side Handle
4 Lock On Slide Switch
5 Sure Grip Handle
6 Battery Seating
7 Pin Wrench
1 Loosen the safety guard locking
screw to allow the guard to spin.
The safety guard is pre-tted to the angle grinder ready for use. The position
of the guard can be adjusted following the steps below using a Phillips head
screwdriver (not supplied).
3 Tighten the safety guard locking
screw to secure in position.
1 To t, screw the side handle
clockwise into 1 of 3 handle
positions.
2 Rotate the guard into the desired
position.
2 To remove, screw the handle
anti-clockwise.
Fitting and Removing the Side Handle
Safety Guard
WARNING! ENSURE THE TOOL IS SWITCHED OFF AND
THE BATTERY IS REMOVED BEFORE PERFORMING ANY
OF THE FOLLOWING TASKS.
WARNING! DO NOT OPERATE THE ANGLE GRINDER
WITHOUT THE SAFETY GUARD FITTED AS POSSIBLE
INJURIES COULD OCCUR.
7
ONLINE MANUAL
Scan this QR Code with your
mobile device to take you to the
online manual.
BATTERY & CHARGER
This tool is compatible with all battery and chargers from the Ozito
Power X Change Range.
For optimal performance, we recommend the use of a 3.0Ah battery or
higher to operate this Power X Change Angle Grinder.
3. REPLACING A GRINDING DISC2. FITTING THE BATTERY
Inserting & Removing the Battery
1 Align the ribs of the battery with
the recess at the back of the
angle grinder & push in until it
clicks into place.
2 To remove, press and hold the
battery release tab and then
slide out.
2 Using the pin wrench loosen
the ange by rotating it anti
-clockwise.
4 Screw the ange back onto the spindle and tighten using the pin wrench
while holding the spindle lock down.
1 Depress and hold the
spindle lock to prevent
the spindle spinning.
3 Remove the ange and
replace the grinding disc
on the spindle.
Product specificaties
| Merk: | Ozito |
| Categorie: | Haakse slijpmachines |
| Model: | PXAGS-500 |
Heb je hulp nodig?
Als je hulp nodig hebt met Ozito PXAGS-500 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Haakse slijpmachines Ozito
4 Oktober 2022
Handleiding Haakse slijpmachines
- Haakse slijpmachines Bosch
- Haakse slijpmachines AEG
- Haakse slijpmachines Bort
- Haakse slijpmachines Einhell
- Haakse slijpmachines Ferm
- Haakse slijpmachines Flex
- Haakse slijpmachines Hikoki
- Haakse slijpmachines Hitachi
- Haakse slijpmachines Kawasaki
- Haakse slijpmachines Makita
- Haakse slijpmachines Metabo
- Haakse slijpmachines Milwaukee
- Haakse slijpmachines Parkside
- Haakse slijpmachines Skil
- Haakse slijpmachines Sparky
- Haakse slijpmachines Trotec
- Haakse slijpmachines Black And Decker
- Haakse slijpmachines Meec Tools
- Haakse slijpmachines Stayer
- Haakse slijpmachines Tacklife
- Haakse slijpmachines Denzel
Nieuwste handleidingen voor Haakse slijpmachines
4 Oktober 2022
4 Oktober 2022
4 Oktober 2022
4 Oktober 2022
4 Oktober 2022
4 Oktober 2022
4 Oktober 2022
4 Oktober 2022
4 Oktober 2022
4 Oktober 2022