Ozito HPW-2030 Handleiding

Ozito Hogedrukreiniger HPW-2030

Lees hieronder de 📖 handleiding in het Nederlandse voor Ozito HPW-2030 (8 pagina's) in de categorie Hogedrukreiniger. Deze handleiding was nuttig voor 27 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/8
HIGH PRESSURE
WASHER
2030psi 1800W
INSTRUCTION MANUAL
SPECIFICATIONS
Input Voltage: 220–240V ~ 50Hz
Wattage: 1800W
Permissible Pressure: 14MPa (2030psi)
Rated Pressure: 10MPa (1450psi)
Rated Flow: 6.0 L/min
Max. Flow: 7.0 L/min
Water Inlet Pressure: 1.2MPa (174psi) Max.
Water Inlet Temp.: 50 C Max.°
Noise Rating: 90dB
IP Rating: IPX5
Tool Weight: 5.7kg
HPW-2030
STANDARD EQUIPMENT
IN ORDER TO MAKE A CLAIM UNDER THIS
WARRANTY YOU MUST RETURN THE PRODUCT
TO YOUR NEAREST BUNNINGS WAREHOUSE WITH
YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO
RETURNING YOUR PRODUCT FOR WARRANTY
PLEASE TELEPHONE OUR CUSTOMER SERVICE
HELPLINE:
Australia 1800 069 486
New Zealand 0508 069 486
3 YEAR REPLACEMENT WARRANTY
Your product is guaranteed for a period of 36 months from
the original date of purchase. If a product is defective it will
be replaced in accordance with the terms of this warranty.
Warranty excludes consumable parts, for example: O-rings,
bearings and accessories.
WARNING
The following actions will result in the warranty being void.
• If the tool has been operated on a supply voltage other
than that specified on the tool.
• If the tool shows signs of damage or defects caused
by or resulting from abuse, accidents or alterations.
• Failure to perform maintenance as set out within the
instruction manual.
• If the tool is disassembled or tampered with in any way.
• Professional, industrial or high frequency use.
WARRANTY
TO ENSURE A SPEEDY RESPONSE PLEASE
HAVE THE MODEL NUMBER AND DATE OF
PURCHASE AVAILABLE. A CUSTOMER SERVICE
REPRESENTATIVE WILL TAKE YOUR CALL
AND ANSWER ANY QUESTIONS YOU MAY
HAVE RELATING TO THE WARRANTY POLICY
OR PROCEDURE.
OZITO Australia/New Zealand (Head Office) 1-23 Letcon Drive, Bangholme, Victoria, Australia 3175.
The benefits provided under this warranty are in addition
to other rights and remedies which are available to you at law.
Our goods come with guarantees that cannot be excluded
at law. You are entitled to a replacement or refund for a major
failure and for compensation for any other reasonably foreseeable
loss or damage. You are also entitled to have the goods repaired
or replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure.
Generally you will be responsible for all costs associated with
a claim under this warranty, however, where you have suffered
any additional direct loss as a result of a defective product you
may be able to claim such expenses by contacting our customer
service helpline above.
ozito.com.au
High Pressure Washer &
Transport Wheels
5m High Pressure Hose, Spray
Gun & Extension Lance
Handle, Spray Gun Holder,
4 x Screws, Accessories Holder
Adjustable Spray Nozzle, Hose
Adaptor, Cleaning Needle
0920
ONLINE MANUAL
Scan this QR Code with
your mobile device to take
you to the online manual.
Attaching the Transport Handle
1. Slide the base of the
handle into the tabs on the
top of the unit.
2. Insert two of the screws
(supplied) through the tabs
and into the handle.
3. Using a Phillips head
screwdriver, tighten the
screws into place.
1. Transport Handle
2. Power Cord Hook
3. Spray Gun Holder
4. Pressure Washer Housing
5. On/O Dial
6. Hose Quick-Release
7. Water Outlet Port
8. Transport Wheels
HIGH PRESSURE WASHER
ACCESSORIES
KNOW YOUR PRODUCT
1. ASSEMBLY
SETUP & PREPARATION
9. Pressure Hose
10. Adjustable Spray Nozzle
11. Spray Gun
12. Hose Adaptor
13. Cleaning Needle
14. Extension Lance
11 12 1310
2
3
4
1
5
6
7
8
9 14
WARNING! ENSURE THE TOOL IS TURNED OFF
AND DISCONNECTED FROM THE POWER SUPPLY
BEFORE PERFORMING ANY OF THE FOLLOWING
OPERATIONS.
Attaching the Spray Gun Holder
1. Slide the Spray Gun holder
into position on the transport
handle.
Attaching the Accessory Holder
1. Slide the accessory holder
into the tabs on the rear of
the unit.
2. Insert the remaining two
screws (supplied) through
the holder and into the
tabs.
3. Using a Phillips head
screwdriver, tighten the
screws into place.
2. PREPARATION
Attaching the Transport Wheels
1. Align the transport wheels
with the mounting holes on
each side of the unit.
2. Push each wheel into
place so they click in
position and can spin
freely.
Attaching the Hose Adaptor
1. Remove plastic protective
cap from water inlet port
and discard.
2. Screw supplied hose
adaptor onto water inlet
port.
Note: The hose adaptor is
tted with a mesh inlet lter.
This lter must be in place
to prevent impurities in the
water source from entering
the unit and damaging the pump.
Connecting the Water Supply
This pressure washer requires a pressurised water
source with a maximum pressure of 1.2MPa (174psi). It is
recommended that a reinforced garden hose (with minimum
diameter of 12mm) is used for the inlet connection. It cannot
be used with a bucket and siphon.
1. Run water through your
garden hose to remove
any foreign matter before
attaching to the pump.
2. Attach garden hose
(min.Ø 1/2”) to the hose
adaptor on the water inlet
port of the unit. Always
use a reinforced hose
with a standard coupling
for water inlet. The hose
length can not be greater
than 8m in length for proper operation.
Note: A lter is tted to the hose adaptor preventing any
debris from entering the pump. Inspect and clean the lter
before use as insufcient water supply could damage the
pump.
3. Pull gently on the hose to ensure the connection is secure.
Connecting the High Pressure Hose
1. Push one end of the
5m pressure hose into
the water outlet port on
the front of the pressure
washer until it clicks into
place.
2. Gently tug on the high
pressure hose to check
that the connection is
secure.
Note: To disconnect the high
pressure hose, slide and
hold the quick-release to the
unlock position while pulling
the hose out.
WARNING! PRESSURISED WATER. SHUT OF WATER
SUPPLY, TURN OFF UNIT AND SQUEEZE THE SPRAY
GUN TRIGGER TO RELIEVE THE PRESSURE BEFORE
DISCONNECTING THE HIGH PRESSURE HOSE.

Product specificaties

Merk: Ozito
Categorie: Hogedrukreiniger
Model: HPW-2030

Heb je hulp nodig?

Als je hulp nodig hebt met Ozito HPW-2030 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Hogedrukreiniger Ozito

Ozito

Ozito PXPWK-2524 Handleiding

8 April 2024
Ozito

Ozito HPW-2030 Handleiding

12 Juni 2023
Ozito

Ozito PWE-1500U Handleiding

17 Mei 2023
Ozito

Ozito PWE-1300U Handleiding

9 Mei 2023
Ozito

Ozito HPW-1885K Handleiding

11 Maart 2023

Handleiding Hogedrukreiniger

Nieuwste handleidingen voor Hogedrukreiniger

Toolland

Toolland DT20016 Handleiding

7 December 2024
Nilfisk

Nilfisk MC 4M Handleiding

7 December 2024
Einhell

Einhell HR 200 Handleiding

4 December 2024
Einhell

Einhell BT-HP 1900 Handleiding

4 December 2024
Einhell

Einhell BT-HP 2100 Handleiding

4 December 2024
King Craft

King Craft KCHR 200 Handleiding

30 November 2024
Ryobi

Ryobi RY80589 Handleiding

26 November 2024
Prowork

Prowork PHR 100 Handleiding

19 November 2024
Kranzle

Kranzle HD 7/122 Handleiding

17 November 2024
Kranzle

Kranzle Quadro 11/140 TST Handleiding

17 November 2024