Ozito GGM-010 Handleiding
Ozito
Lijmpistool
GGM-010
Lees hieronder de 📖 handleiding in het Nederlandse voor Ozito GGM-010 (2 pagina's) in de categorie Lijmpistool. Deze handleiding was nuttig voor 57 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/2
WARNING! Read all safety warnings and all instructions. Failure to follow
the warnings and instructions may result in electric shock, re and/or serious
injury.
Save all warnings and instructions for future reference. The term “power tool”
in the warnings refers to your mains-operated (corded) power tool or battery-
operated (cordless) power tool.
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b. Do not operate power tools in explosive atmospheres, such as in the
presence of ammable liquids, gases or dust. Power tools create sparks which
may ignite the dust or fumes.
c. Keep children and bystanders away while operating a power tool.
Distractions can cause you to lose control.
2. Electrical safety
a. Power tool plugs must match the outlet. Never modify the plug in any
way. Do not use any adapter plugs with earthed (grounded) power tools.
Unmodied plugs and matching outlets will reduce risk of electric shock.
b. Avoid body contact with earthed or grounded surfaces, such as pipes,
radiators, ranges and refrigerators. There is an increased risk of electric shock
if your body is earthed or grounded.
c. Do not expose power tools to rain or wet conditions. Water entering a power
tool will increase the risk of electric shock.
d. Do not abuse the cord. Never use the cord for carrying, pulling or
unplugging the power tool. Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase the risk of electric shock.
e. When operating a power tool outdoors, use an extension cord suitable for
outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric
shock.
f. If operating a power tool in a damp location is unavoidable, use a residual
current device (RCD) protected supply. Use of an RCD reduces the risk of
electric shock.
3. Personal safety
a. Stay alert, watch what you are doing and use common sense when
operating a power tool. Do not use a power tool while you are tired or under
the inuence of drugs, alcohol or medication. A moment of inattention while
operating power tools may result in serious personal injury.
b. Use personal protective equipment. Always wear eye protection. Protective
equipment such as dust mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will reduce personal injuries.
c. Prevent unintentional starting. Ensure the switch is in the off-position before
connecting to power source and/or battery pack, picking up or carrying the
tool. Carrying power tools with your nger on the switch or energising power tools
that have the switch on invites accidents.
d. Remove any adjusting key or wrench before turning the power tool on. A
wrench or a key left attached to a rotating part of the power tool may result in
personal injury.
e. Do not overreach. Keep proper footing and balance at all times. This enables
better control of the power tool in unexpected situations.
f. Dress properly. Do not wear loose clothing or jewellery. Keep your hair,
clothing and gloves away from moving parts. Loose clothes, jewellery or long
hair can be caught in moving parts.
g. If devices are provided for the connection of dust extraction and collection
facilities, ensure these are connected and properly used. Use of dust
collection can reduce dust-related hazards.
h. Do not let familiarity gained from frequent use of tools allow you to become
complacent and ignore tool safety principles. A careless action can cause
severe injury within a fraction of a second.
4. Power tool use and care
a. Do not force the power tool. Use the correct power tool for your application.
The correct power tool will do the job better and safer at the rate for which it was
designed.
b. Do not use the power tool if the switch does not turn it on and off. Any power
tool that cannot be controlled with the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source and/or the battery pack from
the power tool before making any adjustments, changing accessories, or
storing power tools. Such preventive safety measures reduce the risk of starting
the power tool accidentally.
d. Store idle power tools out of the reach of children and do not allow persons
unfamiliar with the power tool or these instructions to operate the power
tool. Power tools are dangerous in the hands of untrained users.
e. Maintain power tools. Check for misalignment or binding of moving parts,
breakage of parts and any other condition that may affect the power tool’s
operation. If damaged, have the power tool repaired before use. Many
accidents are caused by poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc. in accordance with these
instructions, taking into account the working conditions and the work to
be performed. Use of the power tool for operations different from those intended
could result in a hazardous situation.
h. Keep handles and grasping surfaces dry, clean and free from oil and grease.
Slippery handles and grasping surfaces do not allow for safe handling and control
of the tool in unexpected situations.
5. Service
a. Have your power tool serviced by a qualied repair person using only
identical replacement parts. This will ensure that the safety of the power tool is
maintained.
GLUE GUN
10W
2 3 4 5 6 7
Glue Gun Safety Tips
• Do not touch hot glue.
• Do not remove the glue from skin in the event of accidental contact. Immediately
run cold water over and seek medical advice.
• Do not leave glue gun unattended while in use or directly after use.
• Do not touch the nozzle end of the gun while in use or directly after use.
• Do not inhale vapours generated while in use.
• Do not attempt to feed any other materials through the glue gun, eg. crayons,
sealants, candles etc.
POWER TOOL WARNINGS
ELECTRICAL SAFETY
WARNING! When using mains-powered tools, basic safety
precautions, including the following, should always be
followed to reduce risk of re, electric shock, personal injury
and material damage.
Read the whole manual carefully and make sure you know how to switch
the tool off in an emergency, before operating the tool.
Save these instructions and other documents supplied with this tool for
future reference.
The manufacturer cannot accept any liability for damage or accidents which
arise due to a failure to follow these instructions and the safety information.
Note: The supply of 230V and 240V on Ozito tools are interchangeable for
Australia and New Zealand.
If the supply cord is damaged, it must be replaced by the manufacturer, its
service agent or similarly qualied persons in order to avoid hazard.
Using an Extension Lead
Always use an approved extension lead suitable for the power input of this
tool. Before use, inspect the extension lead for signs of damage, wear and
ageing. Replace the extension lead if damaged or defective.
When using an extension lead on a reel, always unwind the lead completely.
Use of an extension lead not suitable for the power input of the tool or which
is damaged or defective may result in a risk of re and electric shock.
To reduce the risk of electric shock, we recommend the use of a residual
current device (rated 30mA or less).
This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience
and knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.
Young children should be supervised to ensure that they do not play with
the appliance.
GGM-010
INSTRUCTION MANUAL
SPECIFICATIONS
Input: 230-240V ~50Hz
Output: 10W
Flow Rate: 6-8g/min
Glue Stick Diameter: 7.2mm
Glue Stick Length: 100mm
Dual Heat Temperatures: 170° - 190°C
Weight: 0.45kg
1 Glues Sticks x 2
2 Protective Nozzle Cover
3 Metal Stand
4 Flow Control Trigger
5 Glue Display
6 Glue Stick Entry
7 Power Cord
ozito.com.au
1
GGM-010
1. LOADING A GLUE STICK
2. OPERATION
WARRANTY
IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY
YOU MUST RETURN THE PRODUCT TO YOUR NEAREST
BUNNINGS WAREHOUSE WITH YOUR BUNNINGS
REGISTER RECEIPT. PRIOR TO RETURNING YOUR
PRODUCT FOR WARRANTY PLEASE TELEPHONE OUR
CUSTOMER SERVICE HELPLINE:
Australia 1800 069 486
New Zealand 0508 069 486
TO ENSURE A SPEEDY RESPONSE PLEASE HAVE
THE MODEL NUMBER AND DATE OF PURCHASE
AVAILABLE. A CUSTOMER SERVICE REPRESENTATIVE
WILL TAKE YOUR CALL AND ANSWER ANY
QUESTIONS YOU MAY HAVE RELATING TO THE
WARRANTY POLICY OR PROCEDURE.
The benefits provided under this warranty are in addition to other rights and
remedies which are available to you at law.
Our goods come with guarantees that cannot be excluded at law. You are
entitled to a replacement or refund for a major failure and for compensation
for any other reasonably foreseeable loss or damage. You are also entitled
to have the goods repaired or replaced if the goods fail to be of acceptable
quality and the failure does not amount to a major failure.
Generally you will be responsible for all costs associated with a claim under
this warranty, however, where you have suffered any additional direct loss as
a result of a defective product you may be able to claim such expenses by
contacting our customer service helpline above.
3 YEAR REPLACEMENT WARRANTY
Your product is guaranteed for a period of 36 months from the original
date of purchase and is intended for DIY (Do It Yourself) use only. If a
product is defective it will be replaced in accordance with the terms of this
warranty. Warranty excludes consumable parts.
WARNING
The following actions will result in the warranty being void.
• If the tool has been operated on a supply voltage other than that
specified on the tool.
• If the tool shows signs of damage or defects caused by or resulting from
abuse, accidents or alterations.
• Failure to perform maintenance as set out within the instruction manual.
• If the tool is disassembled or tampered with in any way.
OZITO Australia/New Zealand (Head Office)
1-23 Letcon Drive, Bangholme, Victoria, Australia 3175.
ONLINE MANUAL
Scan this QR Code with your
mobile device to take you to
the online manual.
Installing the Glue Stick
2 Squeeze the ow control
trigger multiple times to allow
the glue stick to be pushed
down.
1 Insert the glue
stick into the glue
stick entry and
slide down gently.
WARNING! ENSURE THE TOOL IS SWITCHED OFF AND
ALLOWED TO COOL DOWN BEFORE PERFORMING ANY
OF THE FOLLOWING TASKS.
3 Press the surfaces
to be glued
together within
15 seconds for a
strong bond.
2 Squeeze the trigger ow
control to release the glue.
4 To stop the ow of glue from
the gun, release the ow
control trigger.
Tip: Ensure the glue sticks are
heated fully to allow an even ow
of glue.
1 Plug the power cord into a
power point and switch on.
WARNING! DO NOT ALLOW HOT GLUE TO COME IN
CONTACT WITH PRODUCT HOUSING DURING USE.
DESCRIPTION OF SYMBOLS
V Volts Hz Hertz
~ Alternating current W Watts
°C Degrees Celsius Read instruction manual
Double insulated Regulator compliance mark
Product specificaties
| Merk: | Ozito |
| Categorie: | Lijmpistool |
| Model: | GGM-010 |
Heb je hulp nodig?
Als je hulp nodig hebt met Ozito GGM-010 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Lijmpistool Ozito
16 Maart 2024
22 Januari 2023
13 Oktober 2022
Handleiding Lijmpistool
- Lijmpistool Bosch
- Lijmpistool DeWalt
- Lijmpistool Dremel
- Lijmpistool Duro Pro
- Lijmpistool Einhell
- Lijmpistool Ferm
- Lijmpistool Hikoki
- Lijmpistool Kinzo
- Lijmpistool Maestro
- Lijmpistool Makita
- Lijmpistool Metabo
- Lijmpistool Milwaukee
- Lijmpistool Parkside
- Lijmpistool Powerplus
- Lijmpistool Proline
- Lijmpistool Ryobi
- Lijmpistool Silverline
- Lijmpistool Steinel
- Lijmpistool Toolcraft
- Lijmpistool Trotec
- Lijmpistool Vonroc
- Lijmpistool Westfalia
- Lijmpistool Clas Ohlson
- Lijmpistool Black And Decker
- Lijmpistool Steren
- Lijmpistool Cocraft
- Lijmpistool Meec Tools
- Lijmpistool Rapid
- Lijmpistool Tacklife
- Lijmpistool Fieldmann
- Lijmpistool Graphite
- Lijmpistool MSW
- Lijmpistool Craftsman
- Lijmpistool Alpha Tools
- Lijmpistool Hazet
- Lijmpistool Yato
- Lijmpistool Meister Craft
- Lijmpistool Neo
- Lijmpistool NEO Tools
- Lijmpistool Einhell Bavaria
- Lijmpistool Bavaria By Einhell
- Lijmpistool Fixpoint
Nieuwste handleidingen voor Lijmpistool
19 November 2024
15 November 2024
16 Oktober 2024
6 September 2024
10 Juli 2024
18 Juni 2024
18 Juni 2024
10 Juni 2024
27 Mei 2024
7 Mei 2024