Ozito AWG-964 Handleiding
Ozito
Lasapparaat
AWG-964
Lees hieronder de 📖 handleiding in het Nederlandse voor Ozito AWG-964 (6 pagina's) in de categorie Lasapparaat. Deze handleiding was nuttig voor 49 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/6
ONOVERLOAD
OFF
ONOV ERLO AD
OFF
ARC
WELDER
140 Amp
INSTRUCTION MANUAL
SPECIFICATIONS
Input Voltage: 240V ~ 50Hz
Current Range: 55 - 130A
Peak Current: 140A
Duty Cycle: 25% @ 80 amp
Electrode Size: Ø2.0 - 3.2mm
AWG-964
WHAT’S IN THE BOX
Arc Welder
Earth Clamp
Wire Brush / Chipping
Hammer
Welding Mask
Arc Electrode Holder
ozito.com.au
IN ORDER TO MAKE A CLAIM UNDER THIS
WARRANTY YOU MUST RETURN THE PRODUCT
TO YOUR NEAREST BUNNINGS WAREHOUSE WITH
YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO
RETURNING YOUR PRODUCT FOR WARRANTY
PLEASE TELEPHONE OUR CUSTOMER SERVICE
HELPLINE:
Australia 1800 069 486
New Zealand 0508 069 486
3 YEAR REPLACEMENT WARRANTY
Your product is guaranteed for a period of 36 months from
the original date of purchase. If a product is defective it will
be replaced in accordance with the terms of this warranty.
Warranty excludes consumable parts, for example: welding masks
and combination wire brush/chipping hammers.
WARNING
The following actions will result in the warranty being void.
• If the tool has been operated on a supply voltage other
than that specified on the tool.
• If the tool shows signs of damage or defects caused
by or resulting from abuse, accidents or alterations.
• Failure to perform maintenance as set out within the
instruction manual.
• If the tool is disassembled or tampered with in any way.
• Professional, industrial or high frequency use.
WARRANTY
TO ENSURE A SPEEDY RESPONSE PLEASE
HAVE THE MODEL NUMBER AND DATE OF
PURCHASE AVAILABLE. A CUSTOMER SERVICE
REPRESENTATIVE WILL TAKE YOUR CALL
AND ANSWER ANY QUESTIONS YOU MAY
HAVE RELATING TO THE WARRANTY POLICY
OR PROCEDURE.
OZITO Australia/New Zealand (Head Office) 1-23 Letcon Drive, Bangholme, Victoria, Australia 3175.
The benefits provided under this warranty are in addition
to other rights and remedies which are available to you at law.
Our goods come with guarantees that cannot be excluded
at law. You are entitled to a replacement or refund for a major
failure and for compensation for any other reasonably foreseeable
loss or damage. You are also entitled to have the goods repaired
or replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure.
Generally you will be responsible for all costs associated with
a claim under this warranty, however, where you have suffered
any additional direct loss as a result of a defective product you
may be able to claim such expenses by contacting our customer
service helpline above.
1118
ONLINE MANUAL
Scan this QR Code with your
mobile device to take you to
the online manual.
ARC WELDER
ACCESSORIES
1 Carry Handle
2 Internal Cooling Fan
3 Overload LED
4 Current Setting Gauge
5 On/OSwitch
6 Current Regulator Knob
7 Electrode Holder
8 Earth Clamp
9 Wire Brush / Chipping
Hammer
10 Welding Mask
KNOW YOUR PRODUCT
1. ASSEMBLY
1 Install thin (uncoated)
end of Electrode into the
arc electrode holder.
2 Attach the Earth Clamp
to the work piece
ensuring area is free
from paint or dirt so that
there is a good electrical
connection.
SETUP & PREPARATION
3 Connect the Arc Welder power
cord into a power outlet.
Before starting you will require a suitable Electrode according to the
specicmaterialtypeandthickness.
1
2
3
4
8
6
5
9 10
7
WARNING: ENSURE THE TOOL IS SWITCHED OFF AND
DISCONNECTED FROM THE POWER SUPPLY BEFORE
PERFORMING ANY OF THE FOLLOWING STEPS.
WARNING: DO NOT TOUCH THE ELECTRODE WHILE
THE WELDER IS ON.
NOTE: AVOID THE USE OF EXTENSION CORDS.
2. CONTROLS 3. ARC WELDING
Slag
Slag is refuse left around the weld
after welding, this should only be
removed after the weld has cooled
down and is no longer glowing.
Face shield must be worn during
removal of slag.
Welding Current Control
The welding current can be increased or decreased by turning the
welding current control knob. The welding current should be set
accordingtothespecicapplicationandmaterial.
OPERATION
Preparation
Before welding ensure that:
• You have read and understand the safety section of this manual.
• Thereissucientventilation,particularlyatthefrontandrearof
the unit.
• Youhaveanadequatere-ghtingdevicesonhand.
Electrodes & Welding Current
The welding current must be regulated in accordance with the diameter
of the electrode and the thickness of the steel being used.
This will vary with the type of electrodes and material you are using.
Below is a guide suggesting suitable currents & thickness for welding
steel.
Electrode Diameter Welding Current Amps) Thickness of Steel (
¯2.0mm 55 - 75 1.5 - 2mm
¯2.5mm 80 - 105 3 - 5mm
¯3.2mm 105 - 130 4 - 6mm
Striking the Arc
Lower the electrode slowly and proceed to strike the electrode tip
against the desired join area on the work piece as if you are striking
a match. As soon as you have the arc, try to maintain a distance from
the work piece equal to the diameter of the electrode being used, eg
Ø2.0mm electrode, 2.0mm gap.
WARNING: ENSURE ALL OIL, PETROL AND FLAMMABLE
CONTAINERS HAVE BEEN REMOVED FROM WELDING
AREA.
WARNING: ENSURE APPROVED PROTECTIVE
CLOTHING AND WELDING HELMET/MASK IS WORN AT
ALL TIMES TO PROTECT YOUR FACE AND EYES FROM
ARC UV RADIATION AND SPARKS.
1 To increase the welding
current turn the current
regulating knob in a clockwise
direction.
2 To decrease the welding
current turn the current
regulatingknobinaanti-
clockwise direction.
OFF
OFF
On/O Switch
Thermal Overload LED
To turn the welder on press the
on/oswitchtotheOnposition
("I").
To turn the welder of press the on/
oswitchtotheOposition("0").
When illuminated, wait for
the LED to extinguish before
resuming welding.
Note: The cooling fan will only
operate when the welder is
switched On ("I").
Note: This can occur in heavy use
and does not indicate a fault.
ON
OFF
OVERLOAD
WARNING: THE POWER SUPPLY FOR THIS PRODUCT
SHOULD BE PROTECTED BY A RESIDUAL CURRENT
DEVICE (RATED AT 30MA OR LESS). A RESIDUAL
CURRENT DEVICE REDUCES THE RISK OF ELECTRIC
SHOCK.
70-80º
Strike
Keep Consistant
Height
2.0mm
Welding Direction
Product specificaties
| Merk: | Ozito |
| Categorie: | Lasapparaat |
| Model: | AWG-964 |
Heb je hulp nodig?
Als je hulp nodig hebt met Ozito AWG-964 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Lasapparaat Ozito
16 Maart 2024
30 Juni 2023
30 Juni 2023
18 Juni 2023
27 April 2023
22 Maart 2023
15 Oktober 2022
Handleiding Lasapparaat
- Lasapparaat Bavaria
- Lasapparaat Duro
- Lasapparaat Einhell
- Lasapparaat Ferm
- Lasapparaat Gude
- Lasapparaat Gys
- Lasapparaat Holzmann
- Lasapparaat Hyundai
- Lasapparaat Kemppi
- Lasapparaat Kibani
- Lasapparaat Parkside
- Lasapparaat Powerplus
- Lasapparaat Scheppach
- Lasapparaat Silverline
- Lasapparaat Stanley
- Lasapparaat Taurus
- Lasapparaat Telwin
- Lasapparaat Topcraft
- Lasapparaat Weller
- Lasapparaat Workzone
- Lasapparaat Miller
- Lasapparaat Hilti
- Lasapparaat Herkules
- Lasapparaat MSW
- Lasapparaat SainSmart
- Lasapparaat Anova
- Lasapparaat Lincoln Electric
- Lasapparaat Hyper Welding
- Lasapparaat Mag-Torch
- Lasapparaat UNIMIG
- Lasapparaat Amico Power
- Lasapparaat THUN
- Lasapparaat Esab
- Lasapparaat Topex
- Lasapparaat Stamos
Nieuwste handleidingen voor Lasapparaat
9 December 2024
9 December 2024
9 December 2024
9 December 2024
8 December 2024
4 December 2024
4 December 2024
1 December 2024
17 November 2024
16 November 2024