Owon CP024 Handleiding

Owon Meetapparatuur CP024

Lees hieronder de 📖 handleiding in het Nederlandse voor Owon CP024 (4 pagina's) in de categorie Meetapparatuur. Deze handleiding was nuttig voor 45 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

MODEL: CP024

AC/DC CLAMP CURRENT PROBE

1、

、

、、INTRODUCTION

The is a mini size clamp current probe. It can convert the test current into a

voltage output. As an adapter of the oscilloscope, it is very convenient to use

this probe to test AC or DC current in any conductor.All ranges are selected by

toggle switch, easy to operate.It is an ideal tester for maintenance and

inspection work on all types of electrical equipment.

2、

、

、、SAFETY INTRODUCTIONS

Please according to the method of using this manual before operating

equipment, in case the instrument damage.

To maintain the instrument use safety, please do not test beyond the

prescribed current.

Do not use a broken probe signal output line.

When testing working voltage higher than 60 VDC or 30 vac line, please be

careful to use.

Operating environment condition:

1. Secondary safety insulation

2. Secondary pollution

3. Suitable for indoor use

4. Relative humidity below 70%RH

5. Operating temperature: 0C to 40C

Maintenance Essentials:The inspection and maintenance detailed in this

manual shall be handled by professionally qualified maintenance personnel.

Essentials of cleaning:Clean with dry cloth, do not use stain remover, solvent

clean this probe.

Safety symbols description:

Caution, risk of danger (refer to this manual for

specific Warning or Caution information)

Equipment protected throughout by double

insulation or reinforced insulation

Conforms to European Union directives

3、

、

、、Specification

3.1 GENERAL Specification

RANGE：

：

：：4A，40A，400A

Minimum resolution：

：

：：10mA

Band wide up to 200KHz（-3dB）

Error by earth magnetic: ± 30mA max

Remanence(±100A



0A)：

：

：： ± 30mA max

Jaw size: 23mm (Max)

Auto Zero at power on

Low battery/return to zero indicator: When the battery voltage is lower

than the operating voltage, the indicator lights up; When press

the return to zero key, the output automatically return to zero, at

the same time the indicator light on, after the end of the return to

zero yellow and green indicator light automatically out.

Power Supply: 9V 6F22 Battery

Power Consumption:280mW (typical)

Operating temperature and humidity:

0C to 40C ,relative humidity below 70%RH

Store temperature and humidity:

-10C to 60C ,relative humidity below 70%RH

Size: 180mm(L)x 44mm(W)x 30mm(H)

Weight: Approx. 200g

Accessories: Manual,Battery

3.2ELECTRICAL SPECIFICATIONS

Accuracy are (%rdg + Number of current) at 23C5C below 70%RH;

DC CURRENT:

Range

Accuracy

Sensitivity

±1.5%rdg±5d

1 mV/10 m A

40A

±1.5%rdg±5d

1 mV/ 0.1A

300A

±1.5%rdg±5d

1 mV/ 1A

300A~400A

±3.5%rdg±5d

1 mV/ 1A

AC CURRENT:

Range

Accuracy

Sensitivity

±2.0%rdg±5d

1 mV/10mA

40A

±2.0%rdg±5d

1 mV/0.1A

300A

±2.0%rdg±5d

1 mV/ 1A

300A~400A

±3.5%rdg±5d

1 mV/ 1A

4、

、

、、Panel Description

1. Probe jaw

2. Tong head machine

3. Gear switch

4. Power indicator

5. ZERO Key

6. Indicator panel

7. Output socket

8. Low battery/return to zero indicator

Figure 1

5、

、

、、Operating Instruction

5.1 DC current measurement

5.1.1 Choose the right gear 4A,40A or 400A.

（：）Note Turn on and wait about 5 seconds.

5.1.2 Connect the clamp current probe and an apparatus (Fig. 2).

5.1.3 Make sure that the connection wire of the pliers meter is securely

connected to the input end of the oscilloscope.

5.1.4 Before measuring, please press the ZERO back to Zero button until the

oscilloscope read value is zero.

（

（（Note：

：

：：It is normal to read 0~ 1.0mV after pressing the back to zero

button in DC 4A gear.）

）

））

5.1.5 Press the board machine to open the clamp and clamp a wire to be

tested.Confirm that there is no gap between movable and fixed.

5.1.6 Read the current value on LCD.

5.2 AC current measurement

5.2.1 Choose the right gear 4A,40A or 400A.

（：）Note Turn on and wait about 5 seconds.

5.2.2 Connect the clamp current probe and an apparatus (Fig. 2).

5.2.3 Make sure that the connection wire of the pliers meter is securely

connected to the input end of the oscilloscope.

5.2.4 Press the board machine to open the clamp and clamp a wire to be

Product specificaties

Merk:	Owon
Categorie:	Meetapparatuur
Model:	CP024

Heb je hulp nodig?

Als je hulp nodig hebt met Owon CP024 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Meetapparatuur Owon

Owon ORF5060 Handleiding

22 Augustus 2024

Owon HSA015 Handleiding

22 Augustus 2024

Owon HSA1016 Handleiding

5 Mei 2024

Owon DGE3000 Handleiding

4 Mei 2024

Owon CP024 Handleiding

4 Mei 2024

Owon XDS3000 Handleiding

3 Mei 2024

Owon HDS200 Handleiding

3 Mei 2024

Owon AS201 Handleiding

3 Mei 2024

Owon SDS1102 Handleiding

27 Maart 2024

Owon XDM1241 Handleiding

27 Maart 2024

Handleiding Meetapparatuur

Nieuwste handleidingen voor Meetapparatuur

TFA 40.1001 Handleiding

21 December 2024

Ansmann Comfort Check Handleiding

20 December 2024

PCE Instruments PCE-PST 1 X Handleiding

16 December 2024

Steinberg SBS-LF-147 Handleiding

15 December 2024

Steinberg SBS-SM-135C Handleiding

15 December 2024

Steinberg SBS-MT-100 Handleiding

15 December 2024

Steinberg SBS-SM-130C Handleiding

15 December 2024

Steinberg SBS-DT-999 Handleiding

15 December 2024

Steinberg SBS-DL-123D Handleiding

15 December 2024

Steinberg SBS-LF-141 Handleiding

15 December 2024