OSD Audio GLS8 Handleiding


Lees hieronder de đź“– handleiding in het Nederlandse voor OSD Audio GLS8 (4 pagina's) in de categorie Subwoofer. Deze handleiding was nuttig voor 25 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
GLS8
IN-GROUND SUBWOOFER INSTALL GUIDE
GLS 8 INSTALL GUIDE
Tools Needed
Pre Installation
Speaker Wire
Step 1
Step 2
- Trench Spade/Shovel
- Wire Cutter
- Measuring Tape
- Direct Burial Cables
- Silicon Cable Connectors (Optional)
- Outdoor Volume Control (Optional)
Designate the general area where the subwoofer would be most ideal. The
subwoofer should be placed with in 20 feet of the general listening area for
optimum performance. (See Diagram1) The shape and nish would blend
particularly well in your landscape if it is placed near landscape lighting, water
fountain, open planter or swimming pool.
Measure the distance from the designated speaker location
to your stereo receiver. Try to minimize your distance without
compromising on your overall appeal and safety concern.
Once the route is determined, use your spade and trench
to dig the hole for the subwoofer and a wire route between
8”-12” deep once the trench route is completed, lay the cable
in the route. If using the PVC pipe, cut the pipe to length,
ensure all electrical connections are watertight with silicone
burial connectors. Once the cable layout is done, connect the
subwoofer & rell the trench & subwoofer hole.
(See Diagram 2)
- Where is the best place to install the speakers?
- Where will the speakers sound the best?
- Place the speakers in a location where they
will blend in best with their surroundings.
To determine the length and the gauge of speaker wire, you will
need to measure the distance between your receiver/amplier
and the speakers.
- Always buy more than you think you would need.
- Equal wire lengths should always be used to maintain an equal
balance in sound volume.
- Sound quality is lost when using thin wire gauge over a long
distance.
18 AWG minimum - for distances up to ….……………………. . 10 ft
16-2 AWG - from ……………………………………………. 10 to 50 ft
14-4 AWG - from …………………………………………… 50 to 100ft
12-2 AWG - from …………………………………………… 50 to 100ft
Diagram 2
Diagram 1
?
? ?
EARTH
17 inch
8-6 inch
15-17 inch
System Diagrams
Step 3
Connect to a Mono Subwoofer Amplier such as the OSD SMP250. Please note, the red lead indicates positive signal (+) and the
black indicates negative signal (-). Connecting the positive and negative leads incorrectly will cause it to be out of phase and will result
in weaker bass response. (See Diagram 3) Remove 2”- 3” of the outer layer of the speaker wire. Carefully strip ½” of the insulation
covering the speaker conductors within the outer layer and connect to the speaker outputs on the amplier.
For optimum performance combine the GLS8 with our LS2 landscape satellite speakers. Create an unobtrusive stealthy outdoor
sound system with the following system diagrams. Additional system congurations can be created for up to 8 pairs of speakers using
multichannel ampliers and or series parallel wiring.
Note: Please consult your electronics manual for Impedance and Power Rating before wiring a multi speaker system.
GLS 8 INSTALL GUIDE
SMP250 AMPLIFIER
SMP250 (Mono)
SMP250 (Mono)
AMP/RECEIVER
AMP/RECEIVER
Diagram 3


Product specificaties

Merk: OSD Audio
Categorie: Subwoofer
Model: GLS8

Heb je hulp nodig?

Als je hulp nodig hebt met OSD Audio GLS8 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Subwoofer OSD Audio

Handleiding Subwoofer

Nieuwste handleidingen voor Subwoofer