Optex AX-350DH MK3 Handleiding

Optex Niet gecategoriseerd AX-350DH MK3

Lees hieronder de 📖 handleiding in het Nederlandse voor Optex AX-350DH MK3 (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 42 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

AX-350DH MK III

AX-650DH MK III

AX-350DH TS

AX-350DH BT

No.59-1073-0 0406-04

FEATURES

CONTENTS

·Multiple beam installation of up to 4 sets

·Simple optical alignment

·High waterproofing property; jet-proof : IP65

·Wide optical alignment range:

±90 degrees horizontally; ±20degrees vertically

*AX-350DH BT:

±60 degrees horizontally; ±45 degrees vertically

·Reduced possibility of false alarms caused by flying

objects

1. INSTALLATION GOOD PRACTICE

2. PARTS IDENTIFICATION

3. NOTES ON INSTALLATION

4. INSTALLATION METHOD

5. TERMINAL CONNECTIONS

6. WIRING

7. OPTICAL ALIGNMENT

8. BEAM INTERRUPTION TIME ADJUSTMENT

9. RE-TRANSMISSION FUNCTION

10. WALK TEST

11. HEATER UNIT HU-2

12. BACK COVER BC-1

13. DIMENSIONS

14. TROUBLESHOOTING

15. SPECIFICATIONS

-1-

INSTALLATION

INSTRUCTIONS

top/bottom unit AND/OR selectable

maximum detection range: 350ft.(100m)

PHOTOELECTRIC DETECTOR

·Digital communication function

·Cross talk prevention function

·Peak Finder Interface (P.F.I ) of Dual Alignment

Level Indicator

·Mode-specific indicator allowing simple and

accurate optical alignment

·Simple beam alignment without the “Beam

Blocking Tool”

·Minimization of light disturbance

·ATPC ( Auto Transmit Power Control )

to optimize the power of beam

Thank you for purchasing our product.Be sure to read the

following installation instructions carefully before beginning

installation.Make sure that the person in charge of system

management stores this manual carefully for maintenance

and management.

model for beam tower, upper and lower unit unit AND/OR selectable

maximum detection range: 350ft.(100m)

maximum detection range: 650ft.(200m)

Downloaded from manuals search enginewww.Manualslib.com

-3-

28-39inch(0.7-1m)

23.5 inch(60cm)

39 inch(1m)

2. PARTS IDENTIFICATION

Mounting Plate

Wall Mounting Screw

Holes & Waterproof

Plug (x 4)

Vertical Alignment Dial

Terminals

See 5. “TERMINAL” on PAGE6.

Horizontal Alignment Dial

View Finder

Cover Lock Screw

Cover

Unit Base

Mounting Screw

(x 4)

Wiring Hole (x 2)

Monitor Jack

Alignment Level Indicator

Unit Base Pole Mounting

Screw Holes &

W a t e r p r o o f

Plug (x 4)

Rubber

Bushing

Rubber Bush Slot

Pole Mounting

Screw Holes &

Waterproof Plug

(x 4)

Hood

Switch Section

Transmitter

Receiver

Clears the registered address (see 14. “TROUBLESHOOTING” on Page15).

Indicates the registered address by the flickering of the six indicator LEDs for about 10

seconds (see 14. “TROUBLESHOOTING” on Page15).

Switches between high and low the level of infrared beam reception output to the monitor

jack.

Use this switch for multi-level installation (see 7-2. “Master/slave selector switch setting” on

Page8).

Switches the interruption time between the four settings (see 8. “BEAM INTERRUPTION TIME

ADJUSTMENT” on Page11).

This switches the detection time for the top unit when AX-350DH TS / BT in the OR mode.

Switch to the AND mode for detection of simultaneous interruption for the top and the bottom

units and to the OR mode for detection of interruption for either unit (see 7-3. “AND/OR

selector switch setting” on Page8).

Turning the switch to ON in the OR mode fixes the interruption time for the bottom unit to one

second (see 8. “BEAM INTERRUPTION TIME ADJUSTMENT” on Page11).

ADDRESS CLEAR:

ADDRESS CHECK:

MONITOR JACK switch:

MASTER/SLAVE switch:

INTERRUPTION TIME switch:

AND/OR switch:

(AX-350DH TS / BT only)

Resets the registered address to the factory settings

(see 14. “TROUBLESHOOTING” on Page15).

Indicates the registered address by the flickering of the six indicator LEDs for about 10 seconds

(see 14. “TROUBLESHOOTING” on Page15).

Switches between high and low the level of infrared beam reception output to the monitor jack.

Use this switch for multiple beam installation (see 7-2. “Master/slave selector switch setting” on Page8).

When more than one detector with the same address is on the alarm line, switches one of them

to prevent malfunction caused by cross talk (see 14. “TROUBLESHOOTING” on Page15).

Switch to the AND mode for detection of simultaneous interruption for the top and the bottom

units and to the OR mode for detection of interruption for either unit (see 7-3. “AND/OR selector

switch setting” on Page8).

ADDRESS CLEAR:

ADDRESS CHECK:

MONITOR JACK switch:

MASTER/SLAVE switch:

FORCED ADDRESS switch:

AND/OR switch:

(AX-350DH TS / BT only)

BOTTOM UNIT INTERRUPTION TIME switch:

(AX-350DH TS / BT only)

3. NOTES ON INSTALLATION

[2] Alignment angle[1] Detection range and installation height [3] Pole mounting

·Pole size should be diameter

1.9inch(48mm).

·The length of the wiring cable out of

the pole should be within 23.5

inch(60cm).

Without AX-350DH BT

180 degrees (± 90 degrees) 40 degrees (± 20 degrees)

AX-350DH BT

120 degrees (± 60 degrees) 90 degrees (± 45 degrees)

distances between the Receiver and

the Transmitter are listed below:

Horizontally Vertically

35-350ft.(10-100m) : AX-350DH MK III, AX-350DH TS,

AX-350DH BT

65-650ft. (20-200m) : AX-650DH MK III

Normally, the installation height should

be 0.7 – 1.0m. When OR mode is used,

the installation height of lower beam

should be 15cm from the ground.

For best performance, avoid aligning

detectors at 45 degree angles except

AX-350DH BT.

Note

Downloaded from manuals search enginewww.Manualslib.com

-12-

*AX-350DH TS and AX-350DH BT has

alarm output for lower detector.

10. WALK TEST

Make sure that the “Alarm condition”

LED is OFF. If it is illuminated even

when the beams are not blocked,

make optical alignment again.

If the “Alarm condition” LED is

turned ON when the beam is

blocked, installation is complete.

Be sure to conduct a walk test (to

block the infrared beam) at the

following three points:

1. In front of the Transmitter

2. In front of the Receiver

3. At the middle point between the

Transmitter and the Receiver

If the “Alarm condition” LED is not illuminated even if the beam is blocked, follow the instructions in “14.

TROUBLESHOOTING” on Page15 and solve any problem.

Alarm condition

Note

Receiver

Transmitter

Alarm condition

11. HEATER UNIT HU-2 (Option)

11-1. Mounting method

- Feature -

The heat release effect makes the unit less prone to frost.

When connecting the heater unit leads to the wiring, solder the wires or use the

connectors provided with the heater unit and securely connect the wires one by

one.Put the connector on the wires and crimp with pliers, etc.

Remove the cap from the wiring hole and pull the wire through the hole. Then

thread the wiring packing down to about 6 inch from the end of the wire and

securely tighten the cap.

Remove the release paper on the rear of the heater unit and paste the unit in line

with the guide of the mounting plate for both the top and the bottom levels.

Power supply of 24 VAC/DC is required to use the heater unit.

Use separate wiring from that of the detector because the current

draw of the heater unit can be as large as 430 mA each.

Be sure to mount the heater unit for both the top and the bottom

levels. Otherwise the effectiveness may be reduced.

Note

WIRING DISTANCE

AWG18 (0.83mm2)500'(150 )ｍ

AWG16 (1.31mm2)850'(250ｍ)

AWG14 (2.09mm2)1300'(400ｍ)

WIRE SIZE

11-2. Wiring distance between power supply and detector

·Ensure that the wiring distance from the power supply is within the range shown

in the table on the right.

·When using two or more units on one wire, the maximum length is obtained by

dividing the wire length listed below by the number of units used.

*AX-350DH TS and AX-350DH BT has

alarm output for lower detector.

Downloaded from manuals search enginewww.Manualslib.com

Product specificaties

Merk:	Optex
Categorie:	Niet gecategoriseerd
Model:	AX-350DH MK3

Heb je hulp nodig?

Als je hulp nodig hebt met Optex AX-350DH MK3 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Optex

Optex QXI-DT-X5 Handleiding

21 December 2024

Optex SL-650QDP Handleiding

5 December 2024

Optex FTN-AM Handleiding

5 December 2024

Optex AX-100TFR Handleiding

5 December 2024

Optex SIP-5030-IP-BOX Handleiding

5 December 2024

Optex VXS-AM Handleiding

5 December 2024

Optex WXI-R Handleiding

5 December 2024

Optex AP2-20N Handleiding

23 September 2024

Optex CW-G2 Handleiding

5 Augustus 2024

Optex WXS-RDAM Handleiding

17 Mei 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Philips Quick Clean Pot QCP10 Handleiding

24 December 2024

Philips Senseo HD7002 Handleiding

24 December 2024

D-Link DUB-C2 Handleiding

24 December 2024

Nec MultiPresenter Stick DS1-MP10RX1 Handleiding

24 December 2024

Nec DS1-TM01 Handleiding

24 December 2024

Profoto RFi Softbox Octa Handleiding

24 December 2024

Koenic KAP 2523 Handleiding

24 December 2024

Philips HD9921 Handleiding

24 December 2024

Philips Senseo HD7008 Handleiding

24 December 2024

Onkyo IRK1804C Handleiding

24 December 2024