Onfloor Technologies OF20SH Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Onfloor Technologies OF20SH (23 pagina's) in de categorie Boenmachine. Deze handleiding was nuttig voor 64 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/23
1
Operation Manual & Parts List
OF20SH & OF20SL Multi-Purpose Floor Machine
S T IAVE HESE NSTRUCTIONS
Address: 777 South Street, Newburgh, New York 12550-0606
TEL: 877.356.6703 / 845.565.6623
Internet Address: www.onfloor.com / sales@onfloor.com
2
Table of Contents
General Instructions .............................................................................................................. 3
Silica Vacuum Warning .......................................................................................................... 4
Important Safety Instructions ................................................................................................ 5
Electrical Connections ............................................................................................................ 6
Operating Instructions ........................................................................................................... 7
Installation & Changing of Accessory Tools 8............................................................................
Changing and Installation of Attachments ........................................................................... 8
Belt Changing Instructions .................................................................................................. 9
Inner Bowl Removal Instructions ...................................................................................... 10
Inner Bowl Bearing Replacement ...................................................................................... 11
Pulley Bearing Replacement ............................................................................................. 14
General Safety Precautions .................................................................................................. 17
Machine Maintenance ...................................................................................................... 17
OF20SL Handle & Base Assembly Drawing & Parts List ......................................................... 18
OF20SH Handle & Base Assembly Drawing & Parts List ........................................................ 19
OF20SL & SH Outer Bowl Drawing & Parts List ..................................................................... 20
OF20SL & SH Inner Bowl Drawing & Parts List ...................................................................... 21
Troubleshooting Guide ........................................................................................................ 22
Warranty Information ......................................................................................................... 23
3
General Instructions
READ & FOLLOW ALL INSTRUCTIONS BEFORE USING THIS FLOOR
MACHINE
This floor machine will afford you many years of trouble-free operating satisfaction i it i given proper f s
care. l parts have passed rigid quality contro standards befor being assembled to produce the Al l e
finished product. Prior to packaging, units again inspected for assurance of flawless operation.are
This floo machine s protectively packed to preven damag i shipment Wr wa t e n . e recommend that upon
delivery, remov e unit from its carton d carefully inspect it r y possible dam e in transit. A e th an fo an ag
warranty card i affixed to the handle. It is your responsibility to fill it out d send it to r offic to s an ou e
register your purchase and start your warranty. Failure to send us this card in one week upon receipt of the
machine may void e warranty. th
If damage is discovered, immediately notify the transportation compan that delivered your floor y
machine. As shipper, w unable to a e e ar act upon any claim for concealed damage. Yo mus originatu t e any
claim within 5 day of delivery.s
These instructions for your protection and informationare . PLEASE READ
CAREFUL
L
Y! Failure to
follow these precautions could result in injury or discomfort.
Treat this floor machine you would any other high-grade precision-made product Throwing, as .
dropping, unreasonable bumping across thresholds and other misuse may result a damaged unit and in
invalidate the warranty.
[This section intentionally left blank]
13
15
practical using 2 pieces of 2 x 4 lumber or 2 pieces of equal thickness steel. When pressing the old
bearings out it is acceptable to use almost any device as a pushing tool as long as it will fit through the
center opening without touching the pulley. This means a piece of metal tubing or rod or even a piece of
wood that will fit through a 1.29” diameter hole. The same 15/16 socket used to remove the nuts works
well for this. We do not need to be cautious about damaging the old bearings to remove. (see
illustration page 16)
When installing the new bearings, first clean the surface of the opening where the bearings are to enter.
If your pulley has the 4 drive pins installed, I suggest removing them for this process. You will need a
7/16 deep well socket for this. Stand the pulley in the press resting on its front face. Use a pusher device
that will contact the OUTER RACE. It is important that you do NOT press on the inner race to install the
bearings. This will damage the bearings and shorten their life. The best choice for a pushing tool is a
round rod/pipe or piece of wood that is 1-1/2” diameter that will pass through the 1.57” opening in the
pulley. (see illustration on page 16) Many people use a large socket that makes contact with the outer
race but fits through the opening. The first bearing must be pressed all the way down to the bottom of
the cavity, followed by the spacer ring (you don’t want to forget this) then, finally the last bearing. Be
careful not to over press especially if you left the drive pins in the pulley. When properly installed the
last bearing will be below the retaining ring groove and the retaining ring should go in easily.
Installation without a Press
When using this method, use a short piece of wood (or 15/16 socket) and a mallet/hammer to drive the
old bearings from the cast inner bowl. Support the pulley on a piece of wood to prevent damaging it.
We don’t have to be cautious about damaging the old bearings. When installing the new bearings, first
clean the surface of the opening where the bearings are to enter. Turn the pulley over and rest its front
face (or drive pins if present) on the piece of wood. Place the first bearing in the center opening and
place a flat piece of wood or steel across the top of the bearing. It is important that you drive the
bearing in straight AND that you do this by applying force to the outer race. It is OK that the flat steel or
wood is contacting the inner race as long as the outer race is also in contact. Tap the wood/steel plate
with the hammer and slowly drive the bearing until it is flush with the top of the pulley. Now there are 2
ways to proceed. One is to find a round object (large socket, steel tube, steel rod, etc.) that will contact
the outer race and also fit through the opening in the pulley and use this object to further tap the
bearing to the bottom of the cavity. The other way is to use a short wooden dowel ½ or ¾” in diameter
and to tap the outer race with small taps as you work the dowel around the perimeter of the outer race
as you gradually drive the bearing down to the bottom. When the first bearing is installed, follow with
the spacer ring (you don’t want to forget this) then; repeat the same process with the top bearing. Then
install the retaining ring.
Reinstall drive pins, pulley, belts, keeper plates, dust cover in reverse order of removal.
19
OF20SH Handle & Base Assembly Drawing & Parts List
ITEM
DESCRIPTION
QTY
PART
NO.
ITEM
DESCRIPTION
PART
NO.
1
HANDLE ASSY 230 VOLT HI SPEED
1
296732
14
GROMMET
490199
2
QUICK RELEASE PIN W/CABLE
1
456896
15
SCREW, #10-24 X 1
335169
3
SWITCH COVER PLATE
1
221767
16
SWITCH BOX PLATE
281903
4
STRAIN RELIEF
1
285420
17
SCREW, #8-32 X 1/2
385387
5
50 FT POWER CORD
1
493163
18
BRONZE BUSHING
491055
6
MOTOR CORD W/FEMALE PLUG
1
490229
19
SHOULDER BOLT .37-16 X 1/2
491063
7
SCREW, #6-32 X .37, TRS PHLP
2
377155
20
WHEEL BASE ASSY
296570
8
TERMINAL, SPADE, INSUL 14-16 GA
4
490245
21
6 X 2 WHEEL
490903
9
PLUG, 30 AMP MALE (5 HP MOTOR)
1
468800
22
PALNUT
490881
10
TERMINAL, RING XXX
1
429015
23
NUT, STAR WASHER #10
331201
11
TOGGLE SWITCH
1
479187
24
WIRE RETAINER ASSY
479152
12
RUBBER HANDLE GRIP
2
490180
25
SCREW, ALLEN HD 1/4-20 X 5/8
457310
13
WASHER, TOOTH LOCK, #8
4
380709
26
LOCK WASHER 1/4
342858


Product specificaties

Merk: Onfloor Technologies
Categorie: Boenmachine
Model: OF20SH

Heb je hulp nodig?

Als je hulp nodig hebt met Onfloor Technologies OF20SH stel dan hieronder een vraag en andere gebruikers zullen je antwoorden