NUVO Castillo 60/382 Handleiding

NUVO Lamp Castillo 60/382

Lees hieronder de 📖 handleiding in het Nederlandse voor NUVO Castillo 60/382 (1 pagina's) in de categorie Lamp. Deze handleiding was nuttig voor 11 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/1

INSTALLATION AND SAFETY INSTRUCTIONS

FOR YOUR SAFETY

WARNING: BE SURE THE ELECTRICITY TO THE WIRES

YOU ARE WORKING ON IS SHUT OFF; EITHER THE FUSE

IS REMOVED OR THE CIRCUIT BREAKER IS SHUT OFF.

GENERAL

You don’t need special tools to install this fixture. Be sure to

follow the steps in the order given. Under no circumstances

should a fixture be hung on house electrical wires, nor should a

swag type fixture be installed on a ceiling, which contains a

radiant type heating system. Read instructions carefully. If you

are unclear as to how to proceed, consult a qualified electrician.

NOTE: Proper wiring is essential for the safe operation of this

fixture.

FIXTURE ASSEMBLY

Carefully removed the fixture from the carton and check that all

parts are included as shown in figure. Be careful not to misplace

any of the screws or parts, which are needed to install this

fixture.

STEP 1: Using two pairs of pliers to open one link on the end of

the chains (I) and attach the link to the loops (J),

repeat this step for the fixture loops (H).

INSTALLATION

IMPORTANT: Do not attach fixture directly to outlet box.

STEP 1: Secure the mounting bar (A) to outlet box with the

outlet box screws (B).Thread the nut (D) onto the

nipple (E) so that five threads are exposed above the

nut (D). Insert the lock washer (C) and thread the

nipple (E) into the mounting bar (A), then secure with

the nut (D).

BE SURE TO CLOSE ALL CHAIN LINKS COMPLETELY.

STEP 2: Lace wires up through chain (I) and pass wires through

holes in loop (H). We recommend lacing wire up

through every other link of chain (I).

GROUNDING INSTRUCTIONS

STEP 1: Insert the green grounding screw into the hole with two

raised dimples on the mounting bar. Wrap the ground

wire from the fixture (if supplied) around the green

grounding screw, then connect it to ground wire from

the outlet box (if not fixed on the outlet box) using a

wire connector (not supplied). If ground wire from the

fixture is not supplied, wrap the ground wire (if not

fixed on the outlet box) from the outlet box around the

green grounding screw and tighten it.

NEVER CONNECT GROUND WIRE TO BLACK OR WHITE

POWER SUPPLY WIRES.

STEP 2: Take note of the color of the wire(s) on your fixture.

Identify which group your fixture wire(s) falls into and

connect the wires according to the directions below:

GROUP A: Connect to Black

House Wire

GROUP B: Connect to White

House Wire

BLACK WHITE

*PARALLEL WIRE (round &

smooth)

*PARALLEL WIRE (square &

ridged)

WHITE OR GREY WITH

TRACER

WHITE OR GREY WITHOUT

TRACER

BROWN GOLD OR BLACK

WITHOUT TRACER

BROWN, GOLD OR BLACK

WITH TRACER

*NOTE: When parallel wire (SPT-I & SPT-2) is used, the tracer

wire is square shaped or ridged and the less tracer wire is round

in shape or smooth (seen best when viewed from wire end.)

STEP 3: Take your fixture wire(s) from group A and place

evenly against the black wire from the outlet box. Do

NOT twist wires together before using wire connectors.

STEP 4: Fit a wire connector over the wires and screw the

connector clockwise until you feel a firmness.

STEP 5: Try gently to pull the connector off the wires. If you can

pull the connector off, carefully re-do steps 3 and 4, as

above, and check again for a firm connection.

STEP 6: Connect the fixture wire from group B to the white wire

from the outlet box in the same manner. Make sure no

bare wires can be seen outside wire connectors.

FINAL ASSEMBLY

STEP 1: After wires are connected, tuck them carefully inside

outlet box, Raise the canopy (F) and secure the

canopy (F) to mounting bar (A) with the nipple (E) and

the ball nut (G).

STEP 2: Place the glasses (L) and the caps (M) over the

sockets (K) and secure with the retaining rings (N).

STEP 3: Install lamps. (Please do not exceed the maximum

capacity recommended on the socket.)

CLEANING

To clean, wipe fixture with a soft cloth. Clean glass with a mild

soap. Do not use abrasive materials such as scouring pads or

ITEM: 60/382

Product specificaties

Merk:	NUVO
Categorie:	Lamp
Model:	Castillo 60/382

Heb je hulp nodig?

Als je hulp nodig hebt met NUVO Castillo 60/382 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Lamp NUVO

NUVO Harlow 60/4630 Handleiding

11 September 2024

NUVO Laguna 60/5925 Handleiding

11 September 2024

NUVO Ballerina 60/181 Handleiding

11 September 2024

NUVO Ballerina 60/188 Handleiding

11 September 2024

NUVO Gemini 60/4759 Handleiding

11 September 2024

NUVO Fusion 60/4689 Handleiding

11 September 2024

NUVO Bridgeview 60/1703 Handleiding

5 September 2024

NUVO Dupont 60/1822 Handleiding

5 September 2024

NUVO Dupont 60/1842 Handleiding

5 September 2024

NUVO Dupont 60/1823 Handleiding

5 September 2024

Handleiding Lamp

Nieuwste handleidingen voor Lamp

Nicols BSW 200 LED Handleiding

22 November 2024

Nicols BSW 10R Handleiding

22 November 2024

Lucide Xentrix 23955/24/30 Handleiding

22 November 2024

Lucide Xantra 23956/05/31 Handleiding

22 November 2024

Lucide Xantra 23956/10/31 Handleiding

22 November 2024

Lucide Xantra 23956/20/31 Handleiding

22 November 2024

Lucide Vario led 24656/10/30 Handleiding

22 November 2024

Lucide Practico 24657/10/30 Handleiding

22 November 2024

Lucide Stian 25400/38/65 Handleiding

22 November 2024

Lucide Timius 25403/40/30 Handleiding

22 November 2024