Nonin GO2 Achieve Handleiding

Nonin Diversen GO2 Achieve

Lees hieronder de 📖 handleiding in het Nederlandse voor Nonin GO2 Achieve (2 pagina's) in de categorie Diversen. Deze handleiding was nuttig voor 11 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Achieve

User Guide

Introduction

Thank you for buying the GO2 Achieve Fingertip Pulse Oximeter.

This small, portable device will give you important information

about your oxygen saturation (the amount of oxygen in your

blood) and pulse rate at your fingertip! The GO2 Achieve is easy

to use and needs no routine maintenance except battery

replacement. This User Guide explains how to use and care for

your GO2 Achieve.

Contents of Package

•GO

Achieve

• One AAA Alkaline Battery

• User Guide

Intended Use

GO2 Achieve is intended to measure blood oxygen saturation

(%SpO2) (the amount of oxygen in your blood) and pulse rate

of both adults and children. It is designed for fingers (not the

thumb) between 0.3 and 1.0 inch (0.8 – 2.5 cm) thick. The index

finger (pointer finger) is most recommended.

Warnings

• Keep the oximeter away from young children. Small items

such as the battery door, battery, and lanyard are choking

hazards.

• Certain activities may pose a risk of injury, including

strangulation, if the lanyard should become wrapped around

your neck. Use the lanyard with caution.

• Before changing batteries, make sure the GO2 Achieve is off

and is not applied to a digit.

Cautions

• The GO2 Achieve might misinterpret excessive movement as

good pulse strength. Limit finger movement as much as

possible when using the device.

• The GO2 Achieve must be able to measure your pulse

properly to give you an accurate reading. Do not put the

device on the same hand/arm when using a blood pressure

cuff or monitor.

• The GO2 Achieve has no alarms. It will not sound if the

amount of oxygen in your blood is low or if your pulse rate is

too high or too low.

• Do not sterilize, autoclave, or place the GO2 Achieve in liquid

or clean it with agents containing ammonium chloride,

isopropyl alcohol, or products that are not listed in this User’s

Guide. Do not pour or spray any liquids onto the GO2

Achieve.

• Any of the following conditions may reduce the performance

of the GO

Achieve:

- flickering or very bright light;

- weak pulse quality (low perfusion);

- low hemoglobin;

- arterial catheters;

- nail polish, and/or artificial nails; and

- any tests recently performed on you that required an

injection of intravascular dyes.

• The GO2 Achieve may not work if you have poor circulation.

Rub your finger to increase circulation, or place the device on

another finger.

• The GO2 Achieve measures oxygen saturation of functional

hemoglobin. High levels of dysfunctional hemoglobin

(caused by sickle cell anemia, carbon monoxide, etc.) could

affect the accuracy of the measurements.

• Batteries can leak or explode if used or disposed of

improperly. Remove the battery if the GO2 Achieve will be

stored for more than 30 days.

• Do not use the GO2 Achieve in a combustible environment

(oxygen enriched environment).

• Do not use the GO2 Achieve outside the specified operating

and storage temperature ranges.

• Do not use the GO2 Achieve for more than 30 minutes without

relocating the device to another finger.

• The GO2 Achieve needs to be used according to information

provided in the User Guide.

• Do not tamper with, or hang lanyard from the flexible circuit.

• When using the GO2 Achieve in the home, avoid exposing the

GO2 Achieve to lint and dust.

• Field strengths from fixed transmitters, such as base stations

for radio (cellular/cordless) telephones and land mobile

radios, amateur radio, AM and FM radio broadcast towers

and TV broadcast towers may affect accuracy.

• Use in emergency vehicles with communication systems

may affect accuracy.

• Functional tester cannot be used to assess the accuracy of

this pulse oximeter.

• Follow local disposal and recycling laws for the GO2 Achieve

and its components, including the battery.

• The GO2 Achieve is a precision electronic instrument and

must be repaired by Nonin Technical Service.

Symbols

The following symbols are associated with your GO

Achieve.

Installing the Battery

One 1.5 volt AAA-size (LR03) battery powers the GO2 Achieve

for approximately 2400 measurements. Nonin recommends

using alkaline batteries (one is included with each new GO2

Achieve). NOTE: You may use rechargeable batteries; however,

they may require more frequent replacement.

1. Remove the battery door located on the left side of the GO2

Achieve by sliding it towards you.

2. Insert one new 1.5 volt AAA-size battery. Follow the plus (+)

and minus (-) markings for battery direction (as shown inside

of the battery compartment).

3. Carefully reposition the battery door. NOTE: Do not force it

into place; it fits only when positioned correctly.

When battery is low, the battery indicator symbol on the display

will flash. Remove battery if the device will be stored for more

than 30 days. Replace low battery as soon as possible.

Applying the GO

Achieve to Your Finger

Hold the GO2 Achieve with the display facing toward you; slide

your finger into the opening at the bottom of the device, as shown

at right, until the fingertip touches the built-in stop guide. The

index (pointer) finger is recommended.

Have your forearm parallel to the floor when you use the GO2

Achieve. Make sure your finger is centered within the finger guide

and the GO2 Achieve is at heart or chest level.

NOTE: Correct positioning of the device on your finger is critical

for accurate measurements. While on the finger, do not press the

GO2 Achieve against any surface and do not squeeze or hold it

together. The internal spring provides the correct pressure;

additional pressure may cause inaccurate readings.

Verifying Operation

The GO2 Achieve LCD has an integrated backlight that turns on

automatically in low light conditions. This allows the display to be

visible in dark spaces.

If the GO2 Achieve does not turn on or if it shuts off unexpectedly,

remove the GO2 Achieve from your finger, remove the battery

and see the Troubleshooting section. Continually verify

operation.

Reading Your Results

When you put your finger in the GO2 Achieve, you’ll notice an

LCD display come on. The numbers you see show:

• the amount of oxygen in your blood, displayed as %SpO2;

and

• your Pulse Rate, displayed as a 2 or 3 digit number,

measuring the number of times your heart beats per minute.

The Pulse Quality indicator ( ) displays the strength of the pulse

rate signal. Bars will display after the , indicating pulse signal

strength ( ); the greater the number of bars indicates a greater

pulse quality signal strength.

If you are not getting a pulse rate reading and your pulse quality

indicator is weak, warm the finger or reposition to another finger.

While the GO2 Achieve is calculating its reading immediately

after activating the device, the sensor disconnect indicator ( )

will appear. The sensor disconnect indicator also appears when

you remove your finger to indicate the pulse signal is not

detected or when there is excessive motion. If this symbol does

not turn off while your finger is in the device, reposition your

finger or switch to a different finger.

The Battery indicator symbol shows the battery strength

(the less the symbol is filled – the less battery capacity is

available – see chart below). Replace the battery when this

symbol begins to flash.

Symbol Definition of Symbol

Follow Instructions for Use

Caution!

Type BF Applied Part (patient isolation from electrical

shock).

UL Mark for Canada and the United States with

respect to electric shock, fire, and mechanical

hazards only in accordance with:

- ANSI/AAMI ES60601-1:2005/(R)2012 and CAN/

CSA-C22.2 No. 60601-1:14

- ISO 80601-2-61:2011 and IEC 60601-1-11:2015

Battery

IP33

Protected against spraying water and against access

to hazardous parts with a tool, per IEC 60529.

Serial Number

Sensor disconnect; the pulse signal is not detected or

there is excessive motion

Temperature Limitation for storage/shipping

Keep dry

Activating the Device

The GO2 Achieve automatically turns on

when a finger is inserted. When a finger

is inserted, the GO2 Achieve performs a

brief self test, as shown at right. Verify

that all segments of the LCD (Liquid

Crystal Display) appear during the

startup sequence.

= full capacity = near empty,

replace

= half capacity (flashing) = empty,

replace

www.nonin.com

Care and Maintenance

The GO2 Achieve requires no calibration or periodic maintenance

other than battery replacement.

Wipe the device with a soft cloth dampened with a mild detergent

or 10% bleach solution. Do not use undiluted bleach or any

cleaning solution other than those recommended here, as

permanent damage could result. Dry with a soft cloth, or allow to

air dry.

Clean once per week or more frequently if handled by multiple

users.

Caution: Do not sterilize, autoclave, or place the GO2 Achieve

in liquid or clean it with agents containing ammonium chloride,

isopropyl alcohol, or products that are not listed in this User’s

Guide. Do not pour or spray any liquids onto the GO2 Achieve.

Troubleshooting

Parts and Accessories

WARNING: Certain activities may pose a risk of injury, including

strangulation, if the lanyard should become wrapped around your

neck. Use the lanyard with caution.

For more information about Nonin parts and accessories, contact

your distributor, or contact Nonin at (877) 577-2635 (USA and

Canada) or (763) 553-9968.

Specifications

Oxygen Saturation Display Range: 0% to 100%

Pulse Rate Display Range: 18 to 321 beats per minute (BPM)

Oxygen Saturation Declared Accuracy Range: 70% to 100%

SpO2 ±2 digits

Low Perfusion Oxygen Saturation Declared Accuracy Range

(Arms*): 70% to 100% SpO2 ±2 digits

Pulse Rate Declared Accuracy Range (Arms*): 20 to 250 BPM

±3 digits

Low Perfusion Pulse Rate Declared Accuracy Range

(Arms*): 40 to 240 BPM ±3 digits

Measurement Wavelengths and Output Power:

Red: 660 nanometers @ 0.8 mW Max. Average

Infrared: 910 nanometers @ 1.2 mW Max. Average

Temperature:

Operating: +41 °F to +104 °F (5 °C to +40 °C)

Storage/Transportation: -22 °F to +158 °F (-30 °C to +70 °C)

Time (from storage) for monitor to be ready for its intended

use:

7 minutes to warm from -30 °C to 5 °C

12 minutes to cool from 70 °C to 40 °C

Device temperature will not exceed 41 °C as measured during a

controlled environment test.

Humidity:

Operating: 10% to 90% relative humidity, non-condensing

Storage/Transportation: 10% to 95% relative humidity, non-

condensing

Operating Altitude: Up to 13,123 feet / 4,000 meters

Battery Life:

Continuous: Approximately 2400 spot checks based on ~21

hours of operation using one AAA-size alkaline battery,

calculated at 30 seconds per use.

Storage: 6 months minimum

Classifications per ANSI/AAMI ES60601-1 and CAN/CSA-

C22.2 No. 60601-1:

Degree of Protection: Type BF-Applied Part

Enclosure Degree of Ingress Protection: IP33

Mode of Operation: Continuous

This device is not made with natural rubber latex.

Testing Summary

GO2 Achieve accuracy and low perfusion testing were conducted

by Nonin Medical, Inc., as described below:

GO2 Achieve Accuracy Testing:

During no-motion conditions at an independent research

laboratory, SpO2 accuracy testing is conducted during induced

hypoxia studies on healthy, male and female, non-smoking, light-

to dark-skinned subjects that are 18 years of age and older. The

measured arterial hemoglobin saturation value (SpO2) of the

sensors is compared to arterial hemoglobin oxygen (SaO2)

value, determined from blood samples with a laboratory co-

oximeter. The accuracy of the sensors in comparison to the co-

oximeter samples measured over the SpO2 range of 70 - 100%.

Low Perfusion Testing:

This test uses a SpO2 Simulator to provide a simulated pulse

rate, with adjustable amplitude settings at various SpO2 levels for

the oximeter to read.

Warranty

Nonin warrants to the purchaser, for 2 years from the date of

purchase, each GO2 Achieve exclusive of the battery. Nonin will

repair or replace any GO2 Achieve found to be defective in

accordance with this warranty, free of charge, for which Nonin

has been notified by the purchaser by serial number that there is

a defect, provided notification occurs within the applicable

warranty period. Nonin reserves the right to replace the device

with a suitable alternative.

This warranty excludes cost of delivery to and from Nonin. Nonin

reserves the right to charge a fee for a warranty repair request on

any GO2 Achieve found to be within specifications. GO2 Achieve

is a precision electronic instrument and must be repaired by

Nonin Technical Service. Any sign or evidence of opening the

GO2 Achieve, field service by non-Nonin personnel, tampering,

or any kind of misuse of the GO2 Achieve, shall void the warranty.

The GO2 Achieve is warranted for consumer use only. All non-

warranty work shall be done at Nonin’s standard rates and

charges in effect at the time of delivery to Nonin.

Please take a moment to find and record the 9-digit serial number

found on the back of your GO2 Achieve. You’ll need this number

if you have to contact Nonin with technical service issues or if you

have any questions regarding the use or performance of your

pulse oximeter. Nonin’s technical service department can be

reached at (877) 577-2635.

My Serial Number:_________________________________

Nonin Medical, Inc.

13700 1st Avenue North

Plymouth, MN 55441, USA

(763) 553-9968

(877) 577-2635

web site: www.nonin.com

email: info@nonin.com

111994-001-02

Problem Possible Cause Possible Solution

Display

lockup

Display does not

appear to change

(you should see a

change to the pulse

indicator if the

device is on the

finger).

Reposition finger or change

fingers.

Remove and replace battery.

If the problem persists,

contact Nonin Technical

Service.

Display

blank

Finger not properly

inserted.

Reposition finger to activate

the device.

Battery. Verify battery is correctly

inserted. Note: If battery is

installed backwards, the unit

will not function.

Dead battery. Replace

battery.

If the problem persists,

remove the battery and

contact Nonin Technical

Service.

Device may be too

cold to operate.

Allow device to sit at room

temperature for at least

10 minutes.

Missing

segments

on LCD

display

Faulty display. Contact Nonin Technical

Service.

No readings Low pulse quality

(no reading).

If the indicator is visible

and the pulse quality bar

graph does not show more

than 2 bars, try the following:

1. Reposition finger.

2. Warm finger by rubbing.

3. Select a different finger.

For more information, please

see Reading Your Results.

GO2CC

Black neoprene carrying case with belt

loop

GO2L Black 20” lanyard

GO2R Clip on retractable holder

Product specificaties

Merk:	Nonin
Categorie:	Diversen
Model:	GO2 Achieve

Heb je hulp nodig?

Als je hulp nodig hebt met Nonin GO2 Achieve stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Diversen Nonin

Nonin 8500 Handleiding

29 Augustus 2023

Nonin Onyx Vantage 9590 Handleiding

29 Augustus 2023

Nonin Onyx 3 - 9591 Handleiding

29 Augustus 2023

Nonin GO2 Achieve Handleiding

29 Augustus 2023

Nonin Avant 9600 Diversen Handleiding

7 Juni 2023

Handleiding Diversen

Nieuwste handleidingen voor Diversen

Fysic FHP-160 Handleiding

23 Oktober 2023

Fysic FC-18 Handleiding

23 Oktober 2023

Fysic FC35 Handleiding

23 Oktober 2023

Ideen Welt Led stekkerdoos verlichting 323043-G Handleiding

17 Oktober 2023

Ideen Welt Thermo koeltas Handleiding

17 Oktober 2023

Ideen Welt Massage MV-25 Handleiding

17 Oktober 2023

Ideen Welt LED sensor LX-LD-P300 Handleiding

17 Oktober 2023

Ideen Welt ZF6865 8 LED Camping lamp Handleiding

17 Oktober 2023

Ideen Welt Muis snoerloos Handleiding

17 Oktober 2023

Ideen Welt Koffer weegscaal Handleiding

17 Oktober 2023