Nitek WB5362 Handleiding

Nitek Wifi-repeater WB5362

Lees hieronder de 📖 handleiding in het Nederlandse voor Nitek WB5362 (6 pagina's) in de categorie Wifi-repeater. Deze handleiding was nuttig voor 63 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/6
WB5326
Wireless Bridge
Quick Start Guide
01/09/12
2
Quick Start Guide
WB5326 Outdoor Wireless Bridge
Items Included in Kit
(1) WB5326 RADIO
(1) PoE (48V, 1A)
(1) Mounting Hardware Accessories
(1) Quick Start Guide
(1) Product CD
Hardware Installation
1. Put an Ethernet cable with RJ-45 connector through the water-tight joint. Make the RJ-45 connector as a 568B
wiring configuration:
2. Using the hardware provided mount the Bridge unit in position. Make sure that the Ethernet connection is
facing down. Keep in mind that the unit has a built-in antenna and must have line of sight between units. Refer
to separate mounting guide sheet for illustrations of hardware assembly.
3. Plug water-tight joint side of the Ethernet cable into the Bridge unit. Connect the other end of the cable to the
power injector supplied with the unit. Also connect a standard RJ-45 network cable for the power injector to a
hub or a terminal.
4. There is a ground connection on enna port. The ground connection should the Bridge unit located near the ant
be connected to a proper earth ground point.
5. The antenna of the Bridge unit is behind the plastic face of the unit and must face the other Bridge unit. Make
sure you have line of site to the opposite unit and that they face each other.
Warning Do not mount Bridge unit near electric power lines, electric
lights or near strong electric power signals
6. Power the unit using the supplied PoE inserter.
12345678
568B
21 4
3
Terminal Wire
1 Orange/White
2 Orange
3 Green/White
4 Blue
5 Blue/White
6 Green
7 Brown/White
8 Brown
3
These instructions are designed for configuring this system to be a network Bridge.
1. Power up each Bridge unit for 30 seconds, then RESET it by pressing the Reset button for 10 seconds.
2. On the PC you will be using to setup the Bridge units, select “Network Connections” in the control Panel. You
can get to it by Start>Settings>Control Panel>Network Connections. Locate the “Local Area Connection”
and right click to select “ ”. When in that tab select “Properties Internet Protocol (TCP/IP)”.
3. Set up a computer with a network IP address of:
IP address 192.168.1.100
Subnet 255.255.255.0
Gateway 192.168.1.254
4. Select and note an IP address for each Bridge unit along with an ID name and password for each unit (see
Example 1). You will also need to select a Channel from 1-11 for all units. Bridge units are designed to work as a
pair. Both units of the pair must operate on the same channel. Different sets should use different channels. For
maximum data speed separate sets by 4 channels or more (i.e., 1, 6, 11).
* Each pair of units must operate on the same channel (1 - 11). Different pairs should use different channels.
Example 1
Unit Your IP Address
For each unit Password Unit ID Channel*
1 xxx.xxx.xxx.1 Build 1 Building One 1
2 xxx.xxx.xxx.2 Build 2 Building Two 1
3
4
5
6

Product specificaties

Merk: Nitek
Categorie: Wifi-repeater
Model: WB5362

Heb je hulp nodig?

Als je hulp nodig hebt met Nitek WB5362 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Wifi-repeater Nitek

Nitek

Nitek WB5362 Handleiding

6 Mei 2023

Handleiding Wifi-repeater

Nieuwste handleidingen voor Wifi-repeater

TP Link

TP Link RE3000X Handleiding

15 November 2024
Medion

Medion P85032 (MD 87070) Handleiding

15 November 2024
HELGI

HELGI HLG0372 Handleiding

10 November 2024
Mercusys

Mercusys Halo H1200G Handleiding

5 November 2024
D-Link

D-Link DMG-112A Handleiding

2 November 2024
Xiaomi

Xiaomi RA75 Handleiding

27 September 2024
Cudy

Cudy RE3000 Handleiding

3 September 2024
Cudy

Cudy RE1200 Handleiding

3 September 2024
Netgear

Netgear EX6170 Handleiding

22 Augustus 2024
Extron

Extron FOX 3G HD-SDI SM Handleiding

15 Augustus 2024