Nikon FSB-U1 Handleiding

Nikon Verrekijker FSB-U1

Lees hieronder de 📖 handleiding in het Nederlandse voor Nikon FSB-U1 (2 pagina's) in de categorie Verrekijker. Deze handleiding was nuttig voor 17 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

1. Compatible Digital Cameras (COOLPIX):

P series (excluding P80)

S series (excluding S10, S4 and cameras with folded optics)

L series (excluding L5 and L1)

2. Combination possible with:

Fieldscope + (MC Eyepiece +FSA-1&2) / (DS Eyepiece)

Spotting scope + (DS Eyepiece)

EZ-Micro

3. Dimensions (when folded):

(W)155 x (H)105 x (D) 95mm

4. Weight:

340g

5. Supplied accessories:

FSB cable release x1, non-skid pad x2, spare scratch-resistant sheet x1

1.Dependingonthetypeofcamera,itsposition,orzoomsetting,vignettingmay

occur.Carefullyadjustthecamerapositionsothatvignettingisminimized.

Vignettingmaynotcompletelydisappear.

2.Whenreplacingbatteriesorrecordingmedia,pleaseremovethecamerafrom

theconnectedequipment.Thenre-attachthecameraandconfirmalignment.

3. Do not carry or transport the bracket while it is mounted on equipment. This may result in it

falling.

4. Carrying or transporting the bracket while it is mounted may result in misalignment of the

camera's position. Re-attach the camera and confirm alignment.

5. There are many adjustable parts on this product. Before using it, thoroughly read about each

of the adjustment/fixing screws and functions to ensure correct use.

6. Do not carry when in viewing position. Switch to shooting position when carrying.

7. Because this product contains various movable metal parts, take care during use to avoid

pinching your fingers and advise children to take special care.

Nomenclature & Functions

① Body (Bracket) Attaches to the eyepieces or DS mount for EZ-Micro. (DS mount: mount for attaching a bracket to EZ-Micro.)

② Bracket fixing screw Two screws tightly fix the bracket to eyepieces or DS mount for EZ-Micro.

③ Mount socket Eyepiece or DS mount for EZ-Micro can be inserted.

④ Camera block fixing screw Fixes the shooting position.

⑤ Camera block handle Hold when moving the camera block for switching between shooting and viewing positions. CAUTION: Do not hold the camera while moving.

⑥ Cable release block fixing screw Fixes the movability and the height of the cable release block. Adjust the cable release position with ⑥ and ⑦ .

⑦ Cable release shaft Cable release can be attached.

⑧ Cable release shaft adjustment screw Place the cable release socket over the center of the shutter release button by sliding the shaft, then fix.

⑨ Cable release socket Screw the cable release in.

⑩ Camera mount Revolving mount for the camera.

⑪Camera fixing screw Adjusts the camera position. Fix it at your desired position.

⑫Camera mount fixing screw Screw for fixing the movability of the camera mount. When using a camera with a zoom lens, exercise caution when setting the zoom so that the lens does not hit against

eyepieces or DS mount.

⑬ Camera mount height adjustment screw Adjusts the height of the camera mount.

⑭ Camera mount height fixing screw Fixes the height of the camera.

Before using the bracket, thoroughly read about each function of the adjustment/fixing screws above to ensure correct use.

1. Attaching the bracket to an eyepiece or a DS mount. (Bracket fixing screw ② ) (Fig.1)

2. Screw the camera to the bracket temporarily. (Camera fixing screw ⑪ ) （Fig.2）

3. Keep the camera away from the bracket by rotating the camera mount ⑨ . (Camera mount fixing screw ⑫ ) (Fig.3)

4. Turn on the digital camera. By operating the zoom button, extend the zoom lens to its maximum length. (Fig.4) Please note that the appearance of the

zoom lens may differ from that shown in Fig.4, depending on the camera.

5. By rotating the camera mount ⑩ , fix the camera so that the end of the zoom lens is placed 5mm in front of the mount socket. (Camera mount fixing screw

⑫ ) Rotate the camera if necessary. (Camera fixing screw ⑪ ) (Fig.5)

Specifications

Attaching the FSB-U1 to a digital camera

Switching between the shooting position and viewing position

Operation Precautions

Shooting Precautions

1. Focus first using the controls on the scope you are using, then make fine adjustments with

the camera's AF function.

2. If you cannot focus on the subject, lock the AF by pressing the shutter release button

halfway, then set the focus while viewing the LCD monitor.

3. With high-magnification shooting, focal depth is low. Be sure to focus carefully.

4. With high-magnification shooting, you can prevent vibration by using a cable release, self-

timer or remote switch.

5. If you notice external light on the monitor or image (picture), use a shield such as a black

cloth to prevent light entering between the mount and lens of the camera.

6. Set in either "P" (Programmed) or "A" (Aperture-Priority) mode.

7. Camera position may become misaligned during camera operation. Before releasing the

shutter, adjust the camera if necessary.

Shooting position:

Screw the camera block fixing fixing

screw ④ tightly.

Viewing position:

Release the camera block fixing screw ④

to open the camera block by 90 degrees.

The camera block is prevented from being

opened wider than 90 degrees by a spring

stopper.

When moving the camera block, please

hold the camera block handle ⑤. Holding

the camera may result in misalignment of

the camera's position.

CAUTION:Dependingonthetypeofcamera,itsposition,orzoomsetting,vignettingmayoccur.Ifvignettingdoesoccur,carefullyadjustthebracket

position.Vignettingmaynotcompletelydisappear.

CAUTION:Whenreplacingbatteriesorrecordingmedia,pleaseremovethecamerafromtheconnectedequipment.Thenre-attachthecameraandconfirm

alignment.

Note: Please refer to the Nomenclature & Functions section above for the numbers, names and functions of the parts described below.

（Fig.1）（Fig.2）（Fig.3）（Fig.4）（Fig.5）

（Fig.6）（Fig.7）

①

⑥

⑬

⑤

⑦

⑪

②

⑧

③

⑨

⑫

⑭

⑩

④

⑧

⑭⑦

⑩

⑥

⑫

⑬

⑤

②

⑪

Spring stopper

④

⑤

④

（Fig.8）

6. Adjust the camera's position horizontally and fix it so that the lens aligns with the center of the camera mount. (Camera fixing screw ⑪ ) (Fig.6)

7. Adjust the camera mount ⑩ vertically (Camera mount height adjustment screw ⑬ ):

By rotating the camera mount height fixing screw ⑭ in a counterclockwise direction, the camera mount ⑩ can be adjusted. Position so that the lens aligns

with the center of the camera mount. Fix its position with the camera mount height fixing screw ⑭ . （Fig.7）

8. While watching the monitor display, adjust the horizontal level of the image by rotating the bracket. (Bracket fixing screw ② )

9. Check if vignetting occurs, across the entire zoom range:

While watching the monitor display, check if vignetting or shadow is visible at the four corners. If vignetting occurs, re-adjust the camera position (back

and forth/horizontally/vertically) (Camera fixing screw ⑪ ) (Camera mount fixing screw ⑫ ) (Camera mount height adjustment screw ⑬ ) (Camera mount

height fixing screw ⑭ ) so that;

・Vignetting and/or shadow are reduced or disappear.

・Vignetting and/or shadow are evened out at the four corners. Depending on the conditions, they may not be completely evened out.

・The closer the end of the lens moves to the eyepieces of the scope or lens of DS mount, the lesser vignetting and/or shadow will appear.

Make sure the end of the zoom lens does not hit against the eyepiece of the scope or lens of the DS mount during zoom adjustment.

10. Place the cable release over the center of the shutter-release button. （Fig.8）

a) Screw the cable release into the cable release socket ⑨ .

b) Adjust the cable release's vertical position. (Space between the cable release shaft and the shutter-release button should be approx. 5mm)

c) Adjust the cable release's horizontal position by rotating the cable release block and by sliding the cable release shaft ⑦ .

d) Fix it with the cable release block fixing screw ⑥ and cable release shaft adjustment screw ⑧ .

11. When shooting with vertical frames, adjust the camera horizontally first, then rotate it.

⑨

⑥

⑦⑧

The center of the

shutter-release button

Product specificaties

Merk:	Nikon
Categorie:	Verrekijker
Model:	FSB-U1

Heb je hulp nodig?

Als je hulp nodig hebt met Nikon FSB-U1 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Verrekijker Nikon

Nikon Travelite VI Handleiding

15 November 2024

Nikon EAGLEVIEW Zoom 8 Handleiding

3 Juni 2023

Nikon Prostaff P3 Handleiding

1 Juni 2023

Nikon Monarch 10x56DCF Handleiding

22 Mei 2023

Nikon Monarch HG 10x30 Handleiding

15 Mei 2023

Nikon Action EX 10x50 Handleiding

14 Mei 2023

Nikon Monarch 5 12x42 Handleiding

10 Mei 2023

Nikon Monarch 8x36DCF Handleiding

7 Mei 2023

Nikon 7x50IF HP WP Tropical Handleiding

7 Mei 2023

Nikon StabilEyes 16x32 Handleiding

3 Mei 2023

Handleiding Verrekijker

Nieuwste handleidingen voor Verrekijker

Bushnell LMSS2 Handleiding

20 December 2024

InfiRay TX60C Handleiding

18 December 2024

InfiRay AC37 Handleiding

18 December 2024

Rexing B1 Basic Handleiding

16 December 2024

Armasight PVS-14 Handleiding

16 December 2024

Opticron Natura BGA ED Handleiding

10 December 2024

Olympus Tracker 8-16x25 Zoom PC I Handleiding

8 December 2024

Olympus Roamer 8x21 DPC I Handleiding

8 December 2024

Minox NV 351 Handleiding

7 December 2024

Sharper Image 100X Ultrazoom Binoculars Handleiding

25 November 2024