Nexa AN-180 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Nexa AN-180 (3 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 194 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/3
AN-180
Plug-in mottagare relÀ/
Plug-in receiver relay
Svenska
AN-180 Àr en liten Z-Wave plug-in relÀmottagare som enkelet ansluts mellan
lasten och eluttaget. Den kan styras av Nexa Bridge eller annan kontroller
som Ă€r Z-Wavecertierad. AN-180 har en knapp för att kunna slĂ„s av och pĂ„
utan fjÀrrkontroll.
SĂ€kerhet
LÀs igenom hela instruktionen först.
Anlita fackman vid behov. Nexa kan ej hÄllas ansvarig om den anvÀndas till
annat Àn den Àr designad för eller om instruktionen inte följs. Anslut aldrig
lampor eller utrustning som överskrider mottagarens maximala belast-
ning. Det kan leda till fel, kortslutning eller brand. Försök inte att reparera
produkten. Den innehÄller inga reparerbara delar. Produkten Àr inte vattentÀt.
Se till att den alltid Àr torr. AnvÀnd inte kemikalier, lösningsmedel eller starka
rengöringsmedel. UtsÀtt inte produkten för stark vÀrme eller kyla.
Teknisk information
InspÀnning 230 V ~50 Hz
Last 1500 W resistiv last
Frekvens Z-Wave (868,42 MHz)
RĂ€ckvidd Upp till 30 m
Dimensioner Ø52 x 78 mm
ArbetstemperatursomrÄde -10°C - 40°C
IP klassicering IP20
Installation
Stoppa i plug-in mottagaren i vÀgguttaget. Stoppa i lastens kontakt i plug-in
mottgaren.
AN-180 kommer ihÄg sitt tillstÄnd om strömmen bryts och sedan kommer
tillbaka (t.ex. vid strömavbrott). Detta kan Àndras i Z-Wave-kontrollenheten.
Inkludering i Z-Wave nÀtverk
PĂ„ enheten nns en knapp [Link Key] som anvĂ€nds för att inkludera, exklu-
dera, och ÄterstÀlla. Se vidare i manualen för Z-Wavekontrollern hur enheten
inkluderas eller exkluderas.
NĂ€r inget nod-id nns lagrat blinkar LED:en i 0,5 Hz.
Autoinkludering
Om enheten inte har har ett nod-id och spÀnningssÀtts sÄ sÀtts den automa-
tiskt i inkluderingslÀge i 4 minuter.
Inkludera Tryck 3 gÄnger pÄ [Link Key] inom 1,5 sekunder.
Exkludera Tryck 3 gÄnger pÄ [Link Key] inom 1,5 sekunder.
ÅterstĂ€llning Tryck 3 gĂ„nger pĂ„ [Link Key] inom 1,5 sekunder.
Tryck, inom 1 sekund, och hÄll [Link Key] nedtryckt
tills dess att LED slocknar.
Enheten Àr nu ÄterstÀlld och stÀller sig i autoinklu-
deringslÀge.
För information angÄnde programmering av Z-Wave modulen, se baksidan.
AnvÀndning
Styrning med Z-Wavekontroller
Se manualen till din Z-Wavekontroller för information hur du styr din motta-
gare.
Styrning med knappen [Link key]
Tryck en gÄng för att tÀnda. Tryck igen för att slÀcka.
mer information pÄ:
www.nexa.se/zwave
English
AN-180 is a small Z-Wave plug-in relay receiver that easly is connected
between wall socket and load. It can be controlled by Nexa Bridge or other
Z-Wave controller. AN-180 has a button for control without a remote.
Safety
Read the instructions rst.
Call in professional as needed. Nexa can not be held responsible if it is used
for other purposes than it is designed for, or if instructions are not followed.
Never connect the lights or equipment that exceeds the recipient’s maximum
load. It can lead to failure, short circuit or re. Do not attempt to repair the
product. It contains no serviceable parts. The product is not waterproof.
Make sure it is completely dry. Do not use chemicals, solvents or harsh
detergents. Do not expose to extreme heat or cold.
Technical information
Power supply 230 V ~50 Hz
Load 1500 W resistive load
Frequency Z-Wave (868,42 MHz)
Range Up to 30 m
Dimensions Ø52 x 78 mm
Environment temp. range -10°C - 35°C
IP classication IP20
Installation
Put the plug-in receiver in the wall socket. Put the loads plug in the receiver.
AN-180 is able to remember the status of the relay when power is cut o
(such as power black-out). When power is supplied again, the unit will resu-
me the last status of the relay (on or o) automatically. This can be changed
in the Z-Wave controller.
Adding to a Z-Wave network
The button marked [Link Key] on the unit is used to include, exclude and
reset the unit.
See Z-Wave controller manual how inclusion/exclusion is done.
The Led ashes 0.5 Hz when no Node ID is stored.
Auto inclusion
If the unit has no Node ID and is powered it enters auto inclusion mode for
4 minutes.
Include Press [Link Key] 3 times within 1,5 seconds.
Exclude Press [Link Key] 3 times within 1,5 seconds.
Reset Press [Link Key] 3 times within 1,5 seconds. Then,
within 1 seconds, press and hold [Link Key] until
LED turns o.
The unit is now reset and enters auto inclusion
mode.
For more information regarding how to program the Z-wave unit, see the
other side.
Operation
Operation with Z-Wave controller
See Z-Wave controller’s manual.
Operation with the button [Link key]
Push once to turn on light, push once again to turn o.
more information at:
www.nexa.se/zwave
an180_86803_manual_002 | 1
Z-Wave Group Support
The unit supports two association groups with 1 node support for Grouping 1 and 4 nodes
support for Grouping 2. This has the eect that when the unit is operating, all devices
associated with the unit will receive the relevant reports.
‱ When the unit is powered up and is already a part of a Z-Wave network, the unit will send
a Notication Report to the node in Group 1.
‱ When setting the unit or changing the unit’s status, the unit will send a Multilevel Switch
Report to the node of Group 1.
‱ When performing Reset the unit will send Device Reset Locally Notication to the node
of Group1.
‱ The minimum interval time between two reports sent from this unit to the node of Group 1
is 3 seconds. Refer to Conguration parameter 2 for more information.
‱ When the button on the unit or the wall switch (S1) is pressed, the unit will send a Basic
Set command to the nodes of Group 2. When the unit is OFF, Basic Set Value = 0x00.
When the unit is ON, Basic Set Value = 0xFF.
Z-Wave Plus Info
Role Type Node Type Installer Icon User Icon
Slave Always On Z-Wave Plus node Light Dimmer Switch Light Dimmer Switch
Version
Protocol Library 3 (Slave_Enhance_232_Library)
Protocol Version 3.95 ( 6.51.02)
Manufacturer
Manufacturer ID Product Type Product ID
0x0060 0x0004 0x0007
AGI (Association Group Information) Table
Group Prole Command Class & Command (List)
N bytes
Group Name(UTF-8)
1General:NA Binary Switch Report,
Notication Report,
Device Reset Locally Notication
Lifeline
2 Basic SetControl:Key1 On/O control
(Button1)
Basic
‱ Basic Get: Inquire about the status of the device.
‱ Basic Report: Report the status of the device.
‱ Basic Set: Set the status of the device.
Basic Set Value Description
0x00 Device OFF
0x01 ~ 0x63 Device ON, output Level as the specied Value.
0xFF Device ON, output Level as the last memorized Level.
Notication
The device will send notications (Notication Type =0x08, Event = 0x01) upon being
powered on.
Conguration
The congurable values are as following:
Basic Set Command value:
Parameter Number DefaultSize Range
120~99 , 255(0xFF) 255 (0xFF)
The delaying time to report to Group 1:
Parameter Number DefaultSize Range
2 1 33 - 25 (seconds)
Remember the last status:
Parameter Number DefaultSize Range
311/0 1: remember
(0: do not remember)
Command Classes
The module supports Command Classes including

‱ COMMAND_CLASS_ZWAVEPLUS_INFO_V2
‱ COMMAND_CLASS_VERSION_V2
‱ COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2
‱ COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1
‱ COMMAND_CLASS_ASSOCIATION_V2
‱ COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1
‱ COMMAND_CLASS_POWERLEVEL_V1
‱ COMMAND_CLASS_BASIC_V1
‱ COMMAND_CLASS_NOTIFICATION_V4
‱ COMMAND_CLASS_CONFIGURATION_V1
‱ COMMAND_CLASS_SWITCH_BINARY_V1
‱ COMMAND_CLASS_SWITCH_ALL_V1
‱ COMMAND_CLASS_FIRMWARE_UPDATE_MD_V2
Additional Command Classes Supported
‱ Power Level: For test purpose during product installation.
‱ Multilevel Switch: Refer to Basic.
‱ Switch All: The device turns on when receiving “Switch All On”, and turns o upon
receiving “Switch All O”.
‱ Firmware Update: For OTA function.
Programming
Is herewith conrmed to comply with the requirements set out in the Council
Directive on the Approximation of the Laws of the Member States relating to
Radio Equipment and Telecommunications Terminal Equipment (RED) Directive
2014/54/EU, Low-voltage Directive (2014/35/EU). For the evaluation regarding the
Directives, the following standards were applied:
EN301489-1 V1.9.2
EN301489-3 V1.6.1
EN300220-1 V2.4.1
EN300220-2 V2.4.1
EN61058-1: 2002/A2: 2008
DIN VDE 0620-2-1: 2013
Company Name: Nexa Trading AB
Adress: Karl Johansgatan 152, 40242, Göteborg, Sweden
Signatur: _ __
Name: Erik Hjelmström
Title: Vice President
Date, Place: 17 May 2016, Göteborg
DECLARATION OF CONFORMITY
an180_86803_manual_002 | 2


Product specificaties

Merk: Nexa
Categorie: Niet gecategoriseerd
Model: AN-180
Kleur van het product: Wit
Diepte: 41 mm
Diameter: 52 mm
Aantal: 1
Maximaal vermogen: 1500 W
Maximum indoorbereik: 30 m
AC-ingangsspanning: 220 - 240 V
AC-ingangsfrequentie: 50 Hz
Connector 1 vormfactor: Recht
Connector 2 vormfactor: Recht
Type stekkeraansluiting: Type C (Europlug)
RF-zendfrequentie: 868.42 MHz
Type stopcontactaansluiting: Type C (Europlug)

Heb je hulp nodig?

Als je hulp nodig hebt met Nexa AN-180 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Nexa

Nexa

Nexa Bridge X Handleiding

23 September 2024
Nexa

Nexa MGDR-3500/SET Handleiding

23 September 2024
Nexa

Nexa MWTT-2 Handleiding

23 September 2024
Nexa

Nexa MWTE-1 Handleiding

23 September 2024
Nexa

Nexa LDR-075 Handleiding

26 Maart 2024
Nexa

Nexa MYCR-2 Handleiding

26 Maart 2024
Nexa

Nexa WT-1 Handleiding

26 Maart 2024
Nexa

Nexa WTE-2 Handleiding

26 Maart 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd