Newco AK-2 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Newco AK-2 (5 pagina's) in de categorie Koffiezetapparaat. Deze handleiding was nuttig voor 39 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/5
Man Pt No 110402 Rev 20170214
ISS 0599
N E W C O E N T E R P R I S E S
INSTALLATION and OPERATION MANUAL
for AK SERIES BREWERS
BREWER SPECIFICATIONS
Model
No of
Warmers
Width
Length
Height*
US 120V
Amps**
Canada 120V
Amps**
AK-1
1
8- 1/2"
16 3/8"-
16 15/16-
12.5
11.2
AK-2
2
8- 1/2"
16 3/8"-
18 9/16-
13.3
10.8
AK-3
3
15 1/2"-
16 3/8"-
16 15/16-
14.2
11.7
AK- LD
N/A
8- 1/2"
16 3/8"-
21 3/16-
14.6
11.7
AK- TC
N/A
8- 1/2"
16 3/8"-
17 5/8-
14.6
11.7
AK AP-
N/A
8- 1/2"
16 3/8"-
22 15/16-
14.6
11.7
AK-D
N/A
8- 1/2"
17 3/8"-
27 3/8-
14.6
11.7
* Height with ABS base shown for Airpot/Dispenser models
** Other Wattages/Voltages available as special order
AK- LD
Note: Decanters and Dispensers not Included
AK-3AS
INSTALLATION / SETUP INSTRUCTIONS
WARNING: - Read and follow installation / setup instructions before plugging or wiring in machine to electrical
circuit. Warranty will be void if machine is connected to any voltage other than that specied on the name plate.
FILL BREWER TANK WITH WATER BEFORE CONNECTING TO POWER SUPPLY !
1) Place the decanter under brew basket, raise top evaporation cover and pour three decanters of water through
the top pour-in screen. Water should come through the brew basket as the third decanter of water drains out of
the pour in basin.
2) Brewer is shipped with thermostat turned on. Plug or wire in machine to appropriate voltage circuit as indicated
on serial tag.
3) Allow 10 to 15 minutes for water in tank to heat to brewing temperature. Additional water may drip from brew
basket on initial expansion of water in the tank. This will not occur thereafter.
4) After water has reached brewing temperature (thermostat will click o, heating noise will stop and green ready
light will be on) pour 1 decanter (60 oz.) of water through pour-in screen. More than 1 decanter of water will
ow into decanter below brew basket due to water expansion in the tank. Machine is now ready to use.
5) Pour 1 decanter of water through pour-in screen to check for the proper temperature setting with an accurate
thermometer. Take the temperature of this water at a point below the brew basket opening, at the start of the
brew cycle and when the decanter is half full. Recommended temperature of the water is approximately 195 F.
6) In higher altitude locations (5000 feet above sea level) the thermostat may have to be adjusted lower to prevent
boiling.
COFFEE PREPARATION PROCEDURES
1) Place lter into brew basket.
2) Put the proper amount of coee into the lter.
3) Slide the brew basket into holder.
4) Place the appropriate empty decanter into position below the brew basket. For airpots rst open lid and remove
pump stem unless it is of the brew thru design. For other dispensers without brew thru lids, remove the lid.
Turn lower warmer switch to the ON position for warmer units.
5) Raise the top evaporation cover and pour one decanter of cold water through the pour in screen into the basin.
Do not overll unit by pouring in more than one decanter of water at a time.
6) Hot water will be delivered through the sprayhead. This distributes the hot water evenly over the coee bed
within the brew basket. The coffee brew will drain from the brew basket into the decanter below.
7) TURN OFF WARMERS WHEN NOT IN USE. Red light in switch indicates when warmer is on.
8) To clean brew basket simply remove from brew rails and dump lter into waste basket. The brewing process,
as described above, can now be started again.
AUTOMATIC WARMER SAFETY SHUT OFF - OPTIONAL FEATURE
Warmer models may be equipped with an electronic control system which automatically monitors the
length of time the warmers are on, and shuts them off after they have been turned on for a preset length of time.
The model number on the serial tag of brewers equiped with this feature is appended by "AS". For example an
AK-3AS is a 3 warmer AK brewer with Automatic Shuto.
The warmer shuto control is initially set at the factory for two hours but the duration of on time for the
warmers may be adjusted anywhere between thirty minutes and four hours, depending on the needs of your
customer. To adjust the time, simply remove the access panel located on the right side of the brewer. Use a
screwdriver to turn the knob. Turning the knob clockwise will increase the on time and counter clockwise will
decrease the length of time the warmers will stay on.
The warmer control circuit will operate all warmers on for the same amount of time. The on time will
automatically be reset to the programmed time when any warmer is turned on. For example, if the customer has
turned on the lower warmer and then 30 minutes later turns on the second warmer, the on time for both warmers
will automatically be reset for the full programmed time of two hours, assuming the factory set time of two hours is
used. This feature eliminates individual warmers shutting o separately. A warmer may be turned o manually by
depressing the appropriate control switch. The red pilot light indicates that the warmer is on.
LIMING
To prevent liming problems in tank fittings remove sprayhead and insert deliming spring all the way into the
tank. When inserted into tank properly, no more than ten inches of the spring should be visible at the
sprayhead tting. Saw back and forth ve or six times. This will keep ttings open and clear of lime. In hard
water areas this should be done everyday. This process takes approximately one minute. In all areas the
sprayhead should be cleaned at least once a week. Where bad liming has already occurred, a new complete
tank assembly may be installed. The tank may be changed in approximately 5-10 minutes time.
WARRANTY
Applies to all equipment manufactured after 2/1/2017. This warranty supersedes
all other previous warranties that are currently in manuals.
Newco warrants equipment manufactured by it for 1 year parts and labor.
Accessories and Dispensers 1 Year parts only.
Electronic Circuit and Control Boards- 3 years parts, 1 year labor.
Equipment manufactured by others and distributed by Newco- please see original equipment
manufacturers warranty, Newco will follow.
These warranty periods run from the date of sale Newco warrants that the equipment manufactured by it
will be commercially free of defects in material and workmanship existing at the time of manufacture and
appearing within the applicable warranty period. This warranty does not apply to any equipment,
component or part that was not manufactured by Newco or that, in Newco’s judgment, has been affected
by misuse, neglect, alteration, improper installation or operation, location or reinstallation, improper re
maintenance or repair, incorrect voltage applied to the unit at any time, damage or casualty. This
warranty does not apply to any equipment failures related to poor water quality, excessive lime and
chlorine and non periodic cleaning and descaling. Warranty is null and void if muriatic or any other form
of hydrochloric acid is used for cleaning or deliming. In addition, this warranty does not apply to
replacement of items subject to normal use including but not limited to user replaceable parts such as
faucet seat cups, sight gauge tubes, washers, o-rings, tubing, seals and gaskets.
This warranty is conditioned on the Buyer 1) giving Newco prompt notice of any claim to be made under
this warranty by telephone at (800) 556-3926 or by writing to 3650 New Town Blvd, Saint Charles, MO
63301; 2) if requested by Newco, shipping the defective equipment prepaid to an authorized Newco
service location; and 3) receiving prior authorization from Newco that the defective equipment is under
warranty.
THE FOREGOING WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER WARRANTY, WRITTEN OR
ORAL, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF EITHER
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. The agents, dealers or employees of
Newco are not authorized to make modications to this warranty or to make additional warranties that are
binding on Newco. Accordingly, statements by such individuals, whether oral or written, do not constitute
warranties and should not be relied upon.
If Newco determines in its sole discretion that the equipment does not conform to the warranty, Newco, at
its exclusive option while the equipment is under warranty, shall either 1) provide at no charge
replacement parts and/or labor (during the applicable parts and labor warranty periods specied above) to
repair the defective components, provided that this repair is done by a Newco Authorized Service
Representative; or 2) shall replace the equipment or refund the purchase price for the equipment.
THE BUYER’S REMEDY AGAINST NEWCO FOR THE BREACH OF ANY OBLIGATION ARISING OUT OF
THE SALE OF THIS EQUIPMENT, WHETHER DERIVED FROM WARRANTY OR OTHERWISE, SHALL BE
LIMITED, AT NEWCO’S SOLE OPTION AS SPECIFIED HEREIN, TO REPAIR, REPLACEMENT OR REFUND.
In no event shall Newco be liable for any other damage or loss, including, but not limited to, lost prots,
lost sales, loss of use of equipment, claims of Buyer’s customers, cost of capital, cost of down time, cost
of substitute equipment, facilities or services, or any other special, incidental or consequential damages.


Product specificaties

Merk: Newco
Categorie: Koffiezetapparaat
Model: AK-2

Heb je hulp nodig?

Als je hulp nodig hebt met Newco AK-2 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Koffiezetapparaat Newco

Handleiding Koffiezetapparaat

Nieuwste handleidingen voor Koffiezetapparaat