Netgear GS116 Handleiding


Lees hieronder de πŸ“– handleiding in het Nederlandse voor Netgear GS116 (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 63 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
)NSTALLATIONξ€€'UIDE
NETGEAR 16-port Gigabit Switch Model GS116
Estimated Time: 5–10 minutes
Unpack the Box and Verify the Contents
When you open the box, verify that you received everything. The package includes:
β€’ NETGEAR 16-port Gigabit Switch Model GS116
β€’ AC power adapter
β€’ Wall-mounting screws
β€’ GS116 Installation Guide (this document)
β€’ Warranty/support information card
If you do not have everything listed above, see the support information card for contact
information. If you are missing the support information card, get contact information at
http://www.NETGEAR.com in the Technical Support section.
Prepare to Install the Switch
Decide where you want to place the switch. Find a flat horizontal surface such as a table,
desk or shelf. The switch comes with wall-mounting screws. You can use the screws if you
want to hang the switch in an open space on a wall.
Make sure the selected location is:
β€’ Not in direct sunlight or near a heater or heating vent.
β€’ Not cluttered or crowded. There should be at least 2 inches (5 cm) of clear space on
all sides of the switch.
β€’ Well ventilated (especially if it is in a closet).
Also, you will need one Category 5 (Cat 5) Ethernet cable with RJ-45 connectors for each
device you want to connect to the switch. Each Ethernet cable must be less than 328 feet
(100 meters).
Install the Switch and Connect the Other Devices
1. Place the switch on a flat surface or hook onto the screws.
2. For each device, insert one end of an Ethernet cable into the port in the device and
insert the other end into one of the Ethernet ports on the switch.
3. Connect the power adapter cord into the back of the switch and then plug the adapter
into a power source (such as a wall socket or power strip).
The Power light should light up.
4. Check the LEDs to confirm that all connections are correct.
LED Activity
Power β€’ On: 16-port Gigabit Switch has power.
β€’Off: No power.
RJ-45 ports β€’ Right LED on: 10 Mbps connection to a powered device.
β€’Left LED on: 100 Mbps connection to a powered device.
β€’Both LEDs on: 1000 Mbps connection to a powered device.
β€’Blink: Activity on this port.
072

!UTO
5PLINK
-BPSξ€€'IGABITξ€€3WITCHξ€€
'3
 ξ€€ ξ€€ ξ€€ ξ€€ ξ€€ ξ€– ξ€€ ξ€€ ξ€€ ξ€€ ξ€€ ξ€— ξ€€ ξ€€ ξ€€ ξ€€ ξ€€ ξ€˜ ξ€™ξ€€ξ€€ξ€€ξ€€ξ€€  
/N,INK
"LINK!CT
"OTH-
--
6 $#ξ€€ξ€‘ξ€Žξ€’ !
ξ€˜ ξ€— ξ€–  ξ€”  ξ€’ 
,/#!,
-
).4%2.%4
/&& /.
072

!UTO
5PLINK
-BPSξ€€'IGABITξ€€3WITCHξ€€'3
 ξ€€ ξ€€ ξ€€ ξ€€ ξ€€ ξ€– ξ€€ ξ€€ ξ€€ ξ€€ ξ€€ ξ€— ξ€€ ξ€€ ξ€€ ξ€€ ξ€€ ξ€˜  
/N,INK
"LINK!CT
"OTH-
--
Power
Troubleshooting
Technical Support
Thank you for selecting NETGEAR products.
After completing the Smart Wizar e the serial number on the d configuration assistant, locat
bottom label of your product, and use it to register your product at
http://www.NETGEAR.com/register.
Registration on the website or over the phone is required before you can use our telephone
support service. The phone numbers for worldwide regional customer support centers are
on the Warranty and Support Information card that came with your product.
Go to http://kbserver.netgear.com for product updates and Web support.
Problem Action
Power light is not lit The switch has no power. Make sure that:
β€’ The power cord is properly connected to the switch.
β€’ The power adapter is properly connected to a functioning power
outlet. If it is in a power strip, make sure the power strip is turned
on. If the socket is controlled by a light switch, make sure the
switch is in the on position.
β€’ You are using the NETGEAR power adapter supplied with your
switch.
Port number light is
not lit for a connected
device, or stays on
continuously
There is a hardware connection problem.
β€’ Make sure the cable connectors are securely plugged in at the
switch and the device.
β€’ Make sure the connected device is turned on.
β€’ If the Ethernet cable is connected to a NIC or other Ethernet
adapter, make sure the card or adapter is installed correctly and
is working.
β€’ Make sure the cable is less than 328 feet (100 meters).
January 18, 2007
This symbol was placed in accordance with the European Union Directive
2002/96 on the Waste Electrical and Electronic Equipment (the WEEE
Directive). If disposed of within the European Union, this product should be
treated and recycled in accordance with the laws of your jurisdiction
implementing the WEEE Directive.
Β© 2007 by NETGEAR, Inc. All rights reserved. NETGEAR is a registered trademark of NETGEAR, Inc. in the
United States and/or other countries. Other brand and product names are trademarks or registered trademarks of
their respective holders. Information is subject to change without notice.
Technical Specifications
Standards compatibility IEEE 802.3i 10BASE-T Ethernet, IEEE 802.3u 100BASE-TX
Fast Ethernet, 1000BASE-T Gigabit Ethernet IEEE 802.3x Flow
Control; IEEE 802.1p and TOS priority, WRR queuing with four
queues. Jumbo Frame Support (up to 9.6 kilobytes/sec.)
Network interface RJ-45 connector for 10BASE-T, 100BASE-TX, or 1000BASE-T
Ethernet interface
Power 18 W max and 12V @ 1.5A DC input
Weight 1.19 kg (2.3 lbs)
Dimensions
(W x D x H)
285 mm (11.22 in) x 103 mm (4.06 in) x 27 mm (1.06 in)
Operating temperature 0 to 50Β° C (32 to 122Β° F)
Operating humidity 10% t0 90% relative humidity, non-condensing
Electromagnetic
compliance
CE mark, Commercial FCC Part 15, Class A EN 55 022 (CISPR
22), C-Tick, VCCI Class A
Power adapter safety
agency approvals
CE mark, Commercial UL listed (UL 1950), C-Tick
Performance Specifications
Frame filter rate 14,800 frames/sec max for 10M port / 148,800 frames/sec max
for 100M port/1,488,000 frames/sec for 1000M port
Frame forward rate 14,800 frames/sec max for 10M port / 148,800 frames/sec max
for 100M port / 1,488,000 frames/sec max for 1000M port
Network latency
(using 64-byte packets)
100 Mbps to 100 Mbps: 40 Β΅s max
1000 Mbps to 1000 Mbps: 10 Β΅s max
Address database size 8000 MAC addresses
Addressing 48-bit MAC address
Queue buffer 272 kilobytes
Regulatory Compliance
Statement of Conditions
In the interest of improving internal design, operational function, and/or reliability, NETGEAR
reserves the right to make changes to the product described in this document without notice.
NETGEAR does not assume any liability that may occur due to the use or application of the
product(s) or circuit layout(s) described herein.
Certificate of the Manufacturer/Importer
It is hereby certified that the NETGEAR Model GS116 Gigabit Ethernet Switch has been suppressed
in accordance with the conditions set out in the BMPT-AmtsblVfg 243/1991 and Vfg 46/1992. The
operation of some equipment (for example, test transmitters) in accordance with the regulations
may, however, be subject to certain restrictions. Please refer to the notes in the operating
instructions.
Federal Office for Telecommunications Approvals has been notified of the placing of this equipment
on the market and has been granted the right to test the series for compliance with the regulations.
Federal Communications Commission (FCC) Compliance Notice:
Radio Frequency Notice
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
β€’ This device may not cause harmful interference, and
β€’ This device must accept any interference received, including interference that may cause
undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
β€’ Reorient or relocate the receiving antenna.
β€’ Increase the separation between the equipment and receiver.
β€’ Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
β€’ Consult the dealer or an experienced radio/TV technician for help.
EN 55 022 Declaration of Conformance
This is to certify that the NETGEAR 16-port Gigabit Switch Model GS116 is shielded against the
generation of radio interference in accordance with the application of Council Directive 89/336/
EEC, Article 4a. Conformity is declared by the application of EN 55 022 Class A (CISPR 22).
Canadian Department of Communications Radio Interference Regulations
This digital apparatus (NETGEAR 16-port Gigabit Switch Model GS116) does not exceed the Class
A limits for radio-noise emissions from digital apparatus as set out in the Radio Interference
Regulations of the Canadian Department of Communications.
Règlement sur le brouillage radioélectrique du ministère des Communications
Cet appareil numΓ©rique (NETGEAR 16-port Gigabit Switch Model GS116) respecte les limites de
bruits radioélectriques visant les appareils numériques de classe A prescrites dans le Règlement sur
le brouillage radioélectrique du ministère des Communications du Canada.


Product specificaties

Merk: Netgear
Categorie: Niet gecategoriseerd
Model: GS116
Gewicht: 900 g
Stroomvoorziening: 5 V @ 5 A DC in
LED-indicatoren: Link, Power
Netwerkstandaard: IEEE 802.1p
Aansluitingen: 16 UTP
Veiligheid: CE Mark, Commercial UL listed (UL 1950), C-Tick
Minimale systeemeisen: Network software (Windows, Linux, Mac OS)
Max. overdrachtssnelheid: 1 Gbit/s
MAC-adrestabel: 8000 entries
Aantal basis-switching RJ-45 Ethernet-poorten: 16
Afmetingen (B x D x H): 285 x 103 x 27 mm
Overdrachtssnelheid: 1000 Mbit/s
Stroomverbruik (typisch): 25 W
Bedrijfstemperatuur (T-T): 0 - 40 Β°C
Relatieve vochtigheid in bedrijf (V-V): 10 - 90 procent
Datalink-protocollen: Ethernet
Latentie: 100 - 100 Mbps): 40 Β΅s; (1000 - 1000 Mbps): 10 Β΅s

Heb je hulp nodig?

Als je hulp nodig hebt met Netgear GS116 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Netgear

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd