Netgear FS309T Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Netgear FS309T (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 246 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
1 2 3 4 5 6 7 8 9
GREE N = FDX , YELLOW = CO L
GREE N = 100M, YELLO W = 10M, BLINKING = AC T
1000M
Ethe rnet
P WR
MODELFS309T
Fast Ethernet Switch
with Gigabit Port
10/100Mbps
Front Panel of the Model FS309T Switch
Rear Panel of the Model FS309T Switch
9462FA
Power
LED FDX LED
Collision LED
10M/100M
Link, Activity LED
1000M
Link, Activity LED
100-2 40V C , 50-60Hz
8765 321
Gigabit Port 10/100M Port Power Socket
Model FS309T
Fast Ethernet Switch
Power code
(for switch)
Installation Guide,
Warranty & Registration Card
and Support Information Card
Installation Hardware
100-240VAC, 50-60Hz
9 7 5 3 2 1
1000 Mbps
100 Mbps
10 Mbps
Key
Model FS309T Switch
Server with Model GA302T
Gigabit Card
9607FA
100-240VAC, 50-60Hz
9 8 7 5 3 2 1
1000 Mbps
100 Mbps
10 Mbps
Key
9608FA
Model DS516
Dual Speed Hub
Model FE508
Fast Ethernet Hub
Model FS309T Switch
Server with Model GA302T
Gigabit Card
Introduction
The NETGEAR®Model FS309T Fast Ethernet Switch provides you
with a low-cost, high-performance network solution and is designed
to support power workgroups operating at either 10 megabits per
second (Mbps) or 100 Mbps, and can relieve server and backbone
bottlenecks with one copper Gigabit Ethernet port.
Verify Package Contents
Product Illustration
Auto Uplink™
The Auto Uplink technology that NETGEAR has included in this
product will automatically sense whether the straight-through cable
plugged into any port should have a ‘normal’ connection, e.g.
connecting to a PC; or an ‘uplink’ connection, e.g. connecting to a
router, switch, or hub. That port will then configure itself to the correct
configuration. This feature also eliminates the need to worry about
crossover cables, as Auto Uplink will accommodate either type of
cable to make the right connection.
Note: Auto Uplink will compensate for setting uplink
connections, and crossover or straight-through cables.
Using Auto Uplink to create multiple paths between any
two network devices will disable your network.
LEDs
This table describes the activity of the Model FS309T switch LEDs.
Label Activity Description Color
PWR On The Switch is receiving power Green
Off The Switch is NOT receiving power
100M/10M On Indicates Link or Activity at 10 Mbps
or 100 Mbps
100 Mbps speed Link GREEN
100 Mbps speed Activity GREEN-Blinking
10 Mbps speed Link YELLOW
10 Mbps speed Activity YELLOW-Blinking
1000M On Indicates Link or Activity at
1000 Mbps
1000 Mbps speed Link GREEN
1000 Mbps speed Activity GREEN-Blinking
FDX/COL On Full Duplex GREEN
Collision YELLOW-Blinking
Applications
Desktop Switching
The Model FS309T switch, used as a desktop switch to build a small
network that enables users to have Gigabit (1000 Mbps) access to a
server.
Segment Switching
The Model FS309T switch can segment a network into multiple
connected pieces, increasing overall bandwidth and throughput. The
Model FS309T switch segmenting networks that are built with a
NETGEAR Model FE508 Fast Ethernet Hub and a NETGEAR Model
DS516 Dual Speed Hub.
Preparing the Site
Before you begin installing your switch, prepare the installation site.
Make sure that your operating environment meets the operating
environment requirements of the equipment.
Characteristic Requirement
Temperature Ambient temperature between 0 and 40 C
(32 and 104 F). No nearby heat sources such as
direct sunlight, warm air exhausts, or heaters.
Operating humidity Maximum relative humidity of 90%,
noncondensing.
Ventilation Minimum 2 inches (5.08 cm) on all sides for
cooling. Adequate airflow in room or wiring closet.
Operating conditions At least 6 feet (1.83 m) to nearest
source of electromagnetic noise (such as
photocopy machine).
Power Adequate power source within 6 feet (1.83 m).
Installing the Switch
Set the switch up on a flat surface; you do not need any special tools.
Be sure the switch is positioned with at least 2 inches of space on all
sides for ventilation.
Connecting Devices
To connect devices to the switch:
1. Connect the devices to the 10/100 Mbps ports on the switch,
using Category 5 UTP cable and an RJ-45 plug.
Note: Ethernet specifications limit the cable length
between your PC or server and the switch to 328 feet
(100 meters)
2. Connect one end of the Category 5 UTP cable to the Gigabit
port and the other end to the linking server or network device.
3. Connect one end of the AC power cord to the power receptacle
on the rear panel of the switch and the other end of the AC
power cord to the wall outlet.
Verifying Installation
When power has been applied to the switch:
• The green Pwr (power) LED on the front panel is on.
When the switch is connected and operating, refer to the table in
“LEDs” for information about the LEDs and their activity.
Troubleshooting Information
Symptom Cause Solution
Power LED No power is Check the power cord connections
is off. received at for the switch and the connected
the hub. device.
Check for a defective adapter card,
cable, or port by testing them in an
alternate environment where all
products are functioning.
Make sure all cables used are
correct and comply with Ethernet
specifications.
Either 10M, Port connection Check the crimp on the RJ-45
100M, or 1000M is not connectors, and make sure that the
Link LED is off functioning. plug is properly inserted and locked
into the port at both the switch and
the connecting device.
Make sure all cables used are
correct and comply with Ethernet
specifications.
One or more Not all system Test the components in an
components are components are alternate environment where all
malfunctioning. properly installed. other components are functioning
properly.
A segment or One or more Verify that the cabling is correct.
device is not devices are not Be sure all cable connectors are
recognized as properly securely positioned in the required
part of the connected or ports. Straight-through cables
network. cabling does not should be used for all standard
meet Ethernet twisted pair connections.
guidelines. Make sure all devices are
connected to the network.
Equipment may have been
accidentally disconnected.
Technical Specifications
Type Specification
Standards ISO/IEC 802-3 (ANSI/IEEE 802.3i) 10BASE-T
Compatibility Ethernet
IEEE 802.3u,100BASE-TX Fast Ethernet
IEEE 802.3ab, 1000BASE-T Gigabit Ethernet
compatible with major network software, including
Windows®networking, NetWare, and Linux
Data Rate 100 Mbps with 4B/5B encoding and MLT-3
physical interface for 100BASE-TX
10 or 100 or 1000 Mbps half-duplex
20 or 200 or 2000 Mbps full-duplex
Network Interface RJ-45 connector for 10BASE-T or 100BASE-TX
or 1000BASE-T Ethernet interface
Power 3.7 w max
Physical Specifications
Dimensions:25.3 x 3.5 x 18.0 cm
Weight:2.86 lb; 1.30 kg
Environmental Specifications
Operating 0 to 40° C (32 to 104° F)
temperature:
Operating 90% maximum relative humidity,
humidity: noncondensing
Electromagnetic CE mark, commercial; FCC Part 15, Class A;
Compliance EN 55 022 (CISPR 22), C-Tick, VCCI A
Safety Agency CE mark, Commercial
Approvals for UL listed (UL 1950)
the Power Adapter
Performance Specifications
Frame filter rate: 14,800 frames/sec max for 10M port
148,000 frames/sec max for 100M port
1,480,000 frames/sec max for 1000M port
Frame forward 14,800 frames/sec max for 10M port
rate: 148,000 frames/sec max for 100M port
1,480,000 frames/sec max for 1000M port
Network latency 100 Mbps to 100 Mbps: 9.5 µs max
(using 64-byte 100 Mbps to 1000 Mbps: 8.5 µs max
packets): 1000 Mbps to 100 Mbps: 3.2 µs max
Address 4000 MAC addresses
database size:
Addressing: 48-bit MAC address
Queue buffer: 128 kilobytes
1
2
3
4
© 2001 by NETGEAR, Inc. All rights reserved.
Trademarks
NETGEAR is a registered trademarks of NETGEAR, Inc. in the United States and in
other countries. Microsoft, Windows, and Windows NT are registered trademarks of
Microsoft Corporation. All other trademarks and registered trademarks are the properties
of their respective owners. All rights reserved. Information subject to change without
notice.
Statement of Conditions
In the interest of improving internal design, operational function, and/or reliability,
NETGEAR reserves the right to make changes to the product described in this document
without notice.
NETGEAR does not assume any liability that may occur due to the use or application of
the product(s) or circuit layout(s) described herein.
Certificate of the Manufacturer/Importer
It is hereby certified that the NETGEAR Model FS309T Fast Ethernet Switch has been
suppressed in accordance with the conditions set out in the BMPT-AmtsblVfg 243/1991
and Vfg 46/1992. The operation of some equipment (for example, test transmitters) in
accordance with the regulations may, however, be subject to certain restrictions. Please
refer to the notes in the operating instructions.
Federal Office for Telecommunications Approvals has been notified of the placing of this
equipment on the market and has been granted the right to test the series for compliance
with the regulations.
VCCI Statement
This equipment is in the Class A category (information equipment to be used in a
residential area or an adjacent area thereto) and conforms to the standards set by the
Voluntary Control Council for Interference by Data Processing Equipment and Electronic
Office Machines aimed at preventing radio interference in such residential areas.
When used near a radio or TV receiver, it may become the cause of radio interference.
Read instructions for correct handling.
Federal Communications Commission (FCC) Compliance Notice:
Radio Frequency Notice
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions:
This device may not cause harmful interference.
• This device must accept any interference received, including interference that may cause
undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commerical environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
EN 55 024 Declaration of Conformance
This is to certify that the NETGEAR Model FS309T Fast Ethernet Switch is shielded
against the generation of radio interference in accordance with the application of Council
Directive 89/336/EEC, Article 4a. Conformity is declared by the application of EN 55 024
Class A (CISPR 22).
Canadian Department of Communications Radio Interference Regulations
This digital apparatus (NETGEAR Model FS309T Fast Ethernet Switch) does not exceed
the Class A limits for radio-noise emissions from digital apparatus as set out in the Radio
Interference Regulations of the Canadian Department of Communications.
Règlement sur le brouillage radioélectrique du ministère des
Communications
Cet appareil numérique (NETGEAR Model FS309T Fast Ethernet Switch) respecte les
limites de bruits radioélectriques visant les appareils numériques de classe A prescrites
dans le Règlement sur le brouillage radioélectrique du ministère des Communications du
Canada.
10/100/1000 Mbps Fast Ethernet FS309T
Fast Ethernet Switch with Gigabit Port
Installation Guide
NETGEAR, Inc.
4500 Great America Parkway
Santa Clara, CA 95054
USA
Phone: 1-888-NETGEAR
E-mail: support@NETGEAR.com
www.NETGEAR.com
Support Information
See Support Information Card for phone numbers.
Internet / World Wide Web
Go to http://www.NETGEAR.com for the NETGEAR Web page.
Defective or damaged merchandise can be returned to your point-of-sale representative.
IMPORTANT!
Please register online. YOU MUST REGISTER TO OBTAIN TECHNICAL SUPPORT. PLEASE
RETAIN PROOF OF PURCHASE and this warranty information. To register your product, get product
support, or to obtain product information and NETGEAR product documentation, direct your Web
browser to the http://www.NETGEAR.com Web page. If you do not have access to the World Wide
Web, you can register your product using the enclosed registration card and mail it to NETGEAR
customer service.
November, 2001
M - F S 3 0 9 T N A - 0


Product specificaties

Merk: Netgear
Categorie: Niet gecategoriseerd
Model: FS309T

Heb je hulp nodig?

Als je hulp nodig hebt met Netgear FS309T stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Netgear

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd