Netgear APS135W Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Netgear APS135W (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 252 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
)NSTALLATION'UIDE
July 2009e
ProSafe Auxiliary Power Supply APS135W
The ProSafe Auxiliary Power Supply APS135W provides a replaceable power supply for the
GSM73xxSv2 series gigabit switches. You can make use of an RPS (Redundant Power
Supply) while replacing the power supply. Refer to the switch Hardware Installation Guide
for additional information. When an RPS is used, the power supply can be replaced without
stopping the switch or requiring a reboot.
Replacing an APS135W Power Supply
Note: The power module has a “hot swap” capability. It is not necessary to remove the AC
power cord from the power supply module when removing the power supply module.
Removing an APS135W Power Supply
To remove the APS135W power module, follow these steps:
1. Loosen the two captive screws on the power module.
2. Remove the power module from the power module slot by pulling on the extraction
handle.
RPS Co nnecto r
Installing an APS135W Power Supply
To install an APS135W power module, follow these steps:
Warning: When inserting a power module into the switches, do not use unnecessary force.
Doing so can damage the connectors on the rear of the supply and on the midplane.
1. Insert the new power supply module into the power module slot, and gently push the
module into the slot.
2. Align the two captive screws with the screw holes in the switch’s back panel.
3. Using a screwdriver, gently tighten the captive screws.
4. If not connected, insert the AC power cord into the power module and connect the
power cord to an AC outlet.
Specifications
Specications
Dimensions (HxWxD) 8.40” x 7.64” x 1.66”
(216mm x 194mm x 42.4 mm)
Weight 2.87 lb (1.3kg)
Operating Temperature 32 to 122 ÂșF (0 to 50 ÂșC)
Storage Temperature -49 to 185 ÂșF (-45 to 85 ÂșC)
Operative relative humidity 10 to 90% and non condensing
MTBF 2,237,887 Hours (~255 years) @ 25 ÂșC
July 2009
This symbol was placed in accordance with the European Union Directive 2002/96 on the Waste
Electrical and Electronic Equipment (the WEEE Directive). If disposed of within the European Union,
this product should be treated and recycled in accordance with the laws of your jurisdiction implementing
the WEEE Directive.
© 2009 by NETGEAR, Inc. All rights reserved. NETGEAR and the NETGEAR logo are registered trademarks of
NETGEAR, Inc. in the United States and/or other countries. Other brand and product names are trademarks or
registered trademarks of their respective holders. Information is subject to change without notice.
July 2009
Technical Support
Thank you for selecting NETGEAR products.
After installing your device, locate the serial number on the label of your product and use it
to register your product at . Registration is required http://www.NETGEAR.com/register
before you can use our telephone support service. Registration via our web site is strongly
recommended.
Go to for product updates and Web supporthttp://kbserver.netgear.com . For Warranty and
Regional Customer Support information, see the that came with your Warranty Card
product.


Product specificaties

Merk: Netgear
Categorie: Niet gecategoriseerd
Model: APS135W

Heb je hulp nodig?

Als je hulp nodig hebt met Netgear APS135W stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Netgear

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd