Nelson 1000 Series On/Off Valves Handleiding

Nelson Besproeiingsbesturing 1000 Series On/Off Valves

Lees hieronder de 📖 handleiding in het Nederlandse voor Nelson 1000 Series On/Off Valves (2 pagina's) in de categorie Besproeiingsbesturing. Deze handleiding was nuttig voor 68 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
Nelson Irrigation Corporation — 848 Airport Road, Walla Walla, WA 99362 USA
Tel: 509 525 7660 — Fax: 509 525 7907 — www.nelsonirrigation.com — info@nelsonirrigation.com
Nelson Irrigation Corporation — 848 Airport Road, Walla Walla, WA 99362 USA
Tel: 509 525 7660 — Fax: 509 525 7907 — www.nelsonirrigation.com — info@nelsonirrigation.com
Nelson Irrigation Corporation — 848 Airport Road, Walla Walla, WA 99362 USA
Tel: 509 525 7660 — Fax: 509 525 7907 — www.nelsonirrigation.com — info@nelsonirrigation.com
WINDOW+
Controller
USERS GUIDE
Features
This battery operated controller irrigates in cycles that will repeat during a window of time
according to a program setup by the user. The wet and off cycles can be very frequent
(over 100 per day) if wanted. It is very useful for evaporative cooling of fruit and dust
suppression when irrigated for short wet/dry interval times. Cycle irrigation is also useful for
normal sequential rotation of irrigation ow between eld zones.
Operates in cycles during programmed window
Battery powered; no need for electrical hookup
Easy installation
Waterproof and weather resistant
Easy programming
Parts Identication
1. Top Cover 2. Controller Display
3. Controller 4. Program keys 5. Solenoid
Getting Started
Basic Controller Functions
This section gives a brief description of the Controller program key buttons. This gure
shows the layout and the function is described below.
Quick presses of the button turn the controller off, or on. Longer presses of MODE
the button put the controller in programming mode. MODE
Press the button to set a function and proceed. SET
Use these buttons to increase and decrease schedule functions.
Installation
The controller and solenoid will normally be installed on the valve at the factory.
Occasionally the latching solenoid valve opens in transit. To ensure that the valve is closed
before you turn on water pressure, rst make sure that the controller is not set to OFF (If
it is set to OFF, press briey on the MODE SET button to turn it on.) Then press + and
simultaneously to open, and press - and simultaneously to close. You are now ready SET
to program the Window+ controller. Caution note: Unique to latch solenoids is the potential
to fail in either OFF or ON! Before installation make certain that the irrigation system has the
proper pressure relief and some protection against damage if solenoid failure occurs.
3W
N.O.
12 VDC
LATCH
1
2
5
3
4
MOD E
SET
Fig. 1
Fig. 1a
MO DE
SE T
Controller on 2” 800 Series valve
Programming the Window (continued)
Setting the OFF Time (Interval)
The following screen shown in Fig 8 will appear:
On this screen the numbers refer to the interval between irrigations within the cycle
(measured in minutes and hours). ‘OFFashes on the screen, alternating with the
numbers.
1. Use the + - buttons to adjust the minutesor
2. Press SET to continue
3. Use the + - buttons to adjust the hours.or
4. Press SET to continue.
Setting the Days
The following screen shown in Fig 9 will appear:
You must select the days you wish the irrigation ‘WINDOW’ to
operate. Each day selected will operate with the irrigation
schedule you setup in Figures 6-8.
1. Press SET to reach the day you wish to irrigate. The number
(corresponding to the day of the week) will ash.
2. Press + to select that day (the square which appears indicates day is selected).
3. Press - to deselect a day (the square will disappear).
4. Press SET until all days are programed as desired. Current day continues ashing.
5. Press SET to complete programming.
Example summary: The program has been set for a 10 hour Window (8:00 to 18:00)
having ‘On’ time duration of 1 hour 30 minutes 9 seconds and ‘OFF’ time interval of 3
hours 30 minutes. This cycle will repeat twice during the 10 hour Window each day
that is selected.
Note: The Window End time takes control over the schedule and turns off the valve even if the
cycle is not complete.
Warranty and Disclaimer: Nelson Window+ controllers are warranted for one year from date of original sale to be free of
defective materials and workmanship when used within the working specications for which the product was designed
and under normal use and service. The manufacturer assumes no responsibility for installation, removal or unauthorized
repair. The manufacturers liability under this warranty is limited solely to replacement or repair of defective parts, and
the manufacturer will not be liable for any crop or other consequential damages resulting from any defects in design or
breach of warranty. This warranty is expressly in lieu of all other warranties, express or implied, including the warranties
of merchantability and tness for particular purposes and of all other obligations or liabilities of manufacturer. No agent,
employee, or representative of the manufacturer has authority to waive, alter or add to the provisions of this warranty,
nor to make representations or warranty not contained herein
Fig. 8
Fig. 9
5
Window+Controller Guide.indd May08
Battery Installation
Replace the battery at the start of each irrigation
season and when the low battery symbol appears.
1. Using a Phillips screwdriver, remove the
four battery cover screws.
2. Remove the battery cover and seal.
3. Replace the battery.
4. After reattaching the seal, put the cover back,
and secure with the four screws.
Maintenance and
Troubleshooting
Seal
Battery cover
Screws
When replacing
seal, push seal tabs
into slots.
Fig. 10
6
Manual Operation
To manually open the valve, make sure that the Controller is not set to OFF (If it is set
to OFF, press briey on the MODE SET button), then press + and simultaneously. The
irrigation will continue until the interval dened in the program has passed. If the irrigation
duration has been set to zero, the valve will close after one minute.
To stop irrigating, press - and simultaneously.SET
Programming the Controller
Meaning of Controller Icons
NOTE: MODE Quick presses of the button turns the
Controller off, or on. Longer presses of the MODE
button put the Controller in programming mode.
1. Irrigating days of the week
2. Cycle start (shows that the time is
within the window cycle has started)
3. Irrigation (valve has been opened)
4. Timing or clock
5. Low battery
6. Time adjustment
NOTE: You cannot program the Controller if it is set to manual operation or if it is set to OFF . To
release from manual operation press - and SET simultaneously. To release from OFF press briey on
the button.MODE
1
3
64
2
5
MODE
SE T
SE T
SE T
Current
Time
Clock
Days of
the week
Setting the Clock
If the screen is blank, press MODE to activate.
To set the program you must be in operating mode.
Before programming the Controller
you must set the clock.
1. Press MODE until the adjustment icon
appears (the minutes will be ashing).
2. Use the + - to adjust the minutesor
3. Press SET
4. Use the + - to adjust the hoursor
5. Press SET
6. Use the + or - to select the current day
7. Press SET to return to operating mode.
Fig. 3
Fig. 2
2
Understanding the ‘WINDOW
The Window is the time between the Start and End of irrigation. The cycle consist of the
‘On’ time (actual irrigation time), and the ‘OFF’ time (interval between irrigation shut off and
the time until the next irrigation begins). The cycle repeatedly recurs during the Window.
NOTE: During programming, the screen will revert to operating mode if left inactive for 30
seconds.
Programming the Window
Setting Window Start Time
1. Press the MODE button until the clock settings screen appears, then press MODE again
until this screen appears (the minutes will be ashing.) On this screen, the clock numbers
refer to the time you wish the Window to begin. ‘Str’ ashes on the screen, alternating with
the numbers.
2. Use the buttons + -or
to adjust the minutes
3. Press SET to continue.
4. Use the buttons + -or
to adjust the hours.
5. Press SET to continue.
Setting the Window End Time
1. The screen in Fig. 5 will appear. On this screen, the clock numbers refer to the time
you wish the irrigation Window to end. ‘End’ ashes on the screen, alternating with the
numbers.
2. Use the buttons+ -or
to adjust the minutes.
3. Press SET to continue.
4. Use the buttons+ -or
to adjust the hours.
5. Press SET to continue.
Example above shows a window Start time of 8:00 and End of 18:00 (a 10 hour Window).
Fig. 4
Fig. 5
3
Programming the Window (continued)
Setting the ON Time (duration)
The following screen shown in Fig. 6 will appear: First the seconds are set then the
hour and minute screen shown in Fig. 7 appears.
On Fig. 6 screen the numbers
refer to the amount of time
(in seconds) the irrigation will
be on each time it activates
within the cycle. The seconds
number ashes and ‘On’
alternately ashes on the screen.
1. Use the buttons to adjust the seconds.+ -or
2. Press SET to continue.
3. For this screen
the ‘On’ time numbers
are measured in hours and minutes.
Use the buttons to adjust the minutes .+ -or
4. Press SET to continue.
5. Use the buttons to adjust the hours.+ -or
6. Press SET to continue.
Fig. 7 example
shows watering duration for each cycle set to 1 hour 30 minutes and 09 seconds.
SET
SET
SET
Fig. 6
Fig. 7
4
Nelson Irrigation Corporation — 848 Airport Road, Walla Walla, WA 99362 USA
Tel: 509 525 7660 — Fax: 509 525 7907 — www.nelsonirrigation.com — info@nelsonirrigation.com
Nelson Irrigation Corporation — 848 Airport Road, Walla Walla, WA 99362 USA
Tel: 509 525 7660 — Fax: 509 525 7907 — www.nelsonirrigation.com — info@nelsonirrigation.com
Nelson Irrigation Corporation — 848 Airport Road, Walla Walla, WA 99362 USA
Tel: 509 525 7660 — Fax: 509 525 7907 — www.nelsonirrigation.com — info@nelsonirrigation.com


Product specificaties

Merk: Nelson
Categorie: Besproeiingsbesturing
Model: 1000 Series On/Off Valves

Heb je hulp nodig?

Als je hulp nodig hebt met Nelson 1000 Series On/Off Valves stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Besproeiingsbesturing Nelson

Handleiding Besproeiingsbesturing

Nieuwste handleidingen voor Besproeiingsbesturing